Kuryakyn 1796 Manual de usuario

TECH-CONNECT FAIRING MOUNT FOR VICTORY 1796

Page 1

This indication alerts you to the fact that ignoring the contents described herein may negatively affect product per-

formance and functionality or damage the product itself or the product to which it is being attached.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN

RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.

STEP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn

IGN OFF.

STEP 2 Remove the windshield; set it and the fasteners aside for now.

Cross Country Tour Models: Remove the two fasteners securing the clutch

-side windshield-mount to the bike; remove the mount; set it and the fasten-

ers aside for now.

STEP 3 Refer to PIC 1. Using warm, soapy water and a clean rag remove all dirt

and debris from the installation area; allow the area to dry completely.

STEP 4 Locate the included Device Holder, Bracket, Flat Washer, and Locknut.

Refer to PIC 2. Place the Bracket over the threaded stud end of the Device

Holder as shown. Secure the Bracket with the Locknut and Flat Washer.

ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:

1 Tech-Connect Device Holder

1 Fairing Mount Bracket

1 Hardware Kit, containing;

4 6” Cable Ties

1 ¼”-20 Thin Nylon Locknut

1 ¼” Flat Washer

YOU WILL ALSO NEED:

Set of Metric hex wrenches, set of open end wrenches, socket set and ratchet, warm, soapy water and a clean rag

Ensure proper adhesion of this product. Remove all grease,

oil, bugs, dirt, and other debris (including wax and polish)

from the installation area. Kuryakyn will not provide warranty

coverage on products or components lost or damaged due

to improper installation.

Do not attempt this installation in temperatures below 50°F

(10°C). Proper adhesive bonding ONLY occurs above 50°F

(10°C).

1796-12MC-1115

Thank You For Choosing Küryakyn!

Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices

regarding the installation, use, and care of this product.

CLEAN + DRY

PIC 1 CLUTCH-SIDE (LEFT)

PIC 2

It is the end user’s responsibility to ensure that all fasteners (including pre-assembled) are tightened before

operation of the motorcycle. Kuryakyn will not provide warranty coverage on products or components lost or

damaged due to improper installation or lack of maintenance. Periodic inspection and maintenance are

required on all fasteners.

Page 2

Refer to PIC 3. Use an open end wrench to hold the threaded

stud while the Locknut is tightened.

Apply the included Foam Pads to the Device Holder.

STEP 5 Refer to PIC 4. Position the Tech Connect Assembly as

shown; align the upper mounting hole.

Remove the Assembly; rub the adhesive backing with your

fingernail to activate the adhesive; remove and discard the

backing.

Again, align the mounting hole and press the Assembly into

place for 60 seconds.

STEP 6 Cross Country Tour Models: Reinstall the windshield mount in

the reverse order it was removed.

STEP 7 Reinstall the windshield in the reverse order it was removed.

Adjust the Device Holder by loosening the square plastic lock-

ing-nut on the backside of the Holder; adjust to desired posi-

tion and tighten the nut.

Open the Device Holder by turning each knob counterclock-

wise until the desired device fits in the claws.

Tighten the Holder by turning the knobs clockwise until they

are snug and the device is secure.

NOTE: Use the included Cable Ties to secure any cords

(charging, audio, etc) leading towards the device in the

Tech Connect.

PIC 3

PIC 4

BEFORE RIDING, ENSURE THAT THE INSTALLATION OF THIS PRODUCT DOES NOT INTERFERE WITH

THE PROPER OPERATION OF THE MOTORCYCLE.

PREVENT DISTRACTED RIDING! DO NOT OPERATE, REMOVE, OR ADJUST THE DEVICE OR HOLDER

WHILE RIDING. DISTRACTED RIDING CAN CAUSE LOSS OF CONTROL LEADING TO SERIOUS INJURY OR

DEATH.

Tabla de contenidos

Otros manuales de Accesorios para motocicletas de Kuryakyn

Kuryakyn

Kuryakyn 3181 Manual de usuario

Kuryakyn

Kuryakyn 8617 Manual de usuario

Kuryakyn

Kuryakyn 5062 Manual de usuario

Kuryakyn

Kuryakyn 7158 Manual de usuario

Kuryakyn

Kuryakyn 4162 Manual de usuario

Kuryakyn

Kuryakyn 1558 Manual de usuario

Kuryakyn

Kuryakyn 4767 Manual de usuario

Kuryakyn

Kuryakyn 6212 Manual de usuario

Kuryakyn

Kuryakyn 4139 Manual de usuario

Kuryakyn

Kuryakyn 1198 Manual de servicio

Kuryakyn

Kuryakyn 4445 Manual de usuario

Kuryakyn

Kuryakyn 1186 Manual de usuario

Kuryakyn

Kuryakyn Pakmaster 444168 Manual de usuario

Kuryakyn

Kuryakyn 9559 Manual de usuario

Kuryakyn

Kuryakyn 4247 Manual de usuario

Kuryakyn

Kuryakyn 7704 Manual de usuario

Kuryakyn

Kuryakyn 5496 Manual de usuario

Kuryakyn

Kuryakyn 3225 Manual de usuario

Kuryakyn

Kuryakyn ISO-SweptWing 4463 Manual de usuario

Kuryakyn

Kuryakyn 2257 Manual de usuario

Kuryakyn

Kuryakyn 7738 Manual de usuario

Kuryakyn

Kuryakyn 7151 Manual de usuario

Kuryakyn

Kuryakyn SADDLEBAG COOLER Manual de usuario

Kuryakyn

Kuryakyn 8446 Manual de usuario

Manuales populares de Accesorios para motocicletas de otras marcas

SRC

SRC B-TRK502-01-01-SL Manual de usuario

3M Speedglas 9100 MP Manual de usuario

hepco & becker

hepco & becker 6307520 00 01 Manual de usuario

HOMCOM

HOMCOM AA0-077 Manual de usuario

hepco & becker

hepco & becker 6307558 00 01 Manual de usuario

Wunderkind Custom

Wunderkind Custom 106503-F15 Guía del usuario

Dräger

Dräger HPS 3500 Manual de usuario

M-WAVE

M-WAVE SKI Manual de usuario

hepco & becker

hepco & becker 6507504 00 01 Manual de usuario

Tool it

Tool it PROMAX LCD 9.13G Manual de usuario

Custom Dynamics

Custom Dynamics TruWrapz Manual de usuario

Roof

Roof RO200 CARBON Manual de usuario

Kabuto

Kabuto Japan IBUKI Manual de usuario

PUIG

PUIG 5051 Manual de usuario

rizoma

rizoma ZTH050 Manual de usuario

Joubert

Joubert 10001711 Manual de usuario

Sperian

Sperian Optrel p420 Manual de usuario

SW-Motech

SW-Motech SBL.01.971.10000/B Manual de usuario