Kubota B2620 Manual de usuario
Kubota B2320 Series ROPS Cab
** Plastic topped cab is shown with optional equipment
Kubota B2320 Series ROPS Cab
This ROPS cab is designed and built to fit the Kubota B2320, B2620, and B2920.
Designed and Built by:
Tektite Manufacturing Inc:
427 Buffalo Street
P.O. Box 639
Winkler, MB
R6W 4A8
Canada
PH: 204-331-3463
Fax: 204-331-4159
www.tektite.ca
One year standard product warranty provided by Tektite.
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
DO NOT PROCEED FURTHER UNTIL YOU HAVE READ THE INFORMATION BELOW
1) Always wear personal protective equipment
2) A minimum of two people is necessary to safely install the cab
3) This ROPS cab is heavy. A lift assist device such as an overhead
hoist or high lift forklift is required.
4) Ensure your work area is well ventilated. The installation
requires the starting of the tractor which will produce
dangerous carbon monoxide fumes.
5) Read through the entire installation manual first.
6) Follow the installation instructions in order.
7) Reading the operators manual prior to using the ROPS cab.
Tektite Manufacturing Incorporated thanks you for purchasing a Kubota B2320 series ROPS cab!
Tektite has worked very hard to design and build this ROPS product and we hope that it
provides you with many years of ROPS protection.
Tektite’s ROPS products are designed to provide safe and dependable service during operation
when they are properly maintained according to the instructions. Please read this installation
manual carefully before installing and using this ROPS product.
The photos/illustrations provided in this manual may not provide all the detail needed, and are
for reference only.
All directions provided are from the reference point of the tractor seat facing the steering
wheel. All left and right references are from this view point.
For reference, please fill in the information below. This will assist your dealer in providing
service for this ROPS. It is advisable that this information be provided to your insurance
company as well in the event that the tractor is lost or damaged.
Vehicle Model: _________________________________________________________
ROPS Serial Number: ___________________________________________________
Date of Purchase: _______________________________________________________
Dealer Name: ___________________________________________________________
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
Parts List Standard Cab:
Description
Qty
Bolt, Flange, 5/8”x 1 ½”, Gr. 8, YD (Loader only)
4
Nut, Flange, 5/8”, Gr. 8, YD (Loader only)
4
Front Brackets (Loader Configuration)
L&R
Bolt, Flange, 5/8” x 3”, Gr. 8, Yellow
4
Nut, Flange, 5/8”, Gr. 8, Yellow
4
Washer, Structural, ¼” Thick
4
Bolt, Flange, 5/16" x 3/4", YD
2
Nut, Flange, 5/16", YD
2
Under seat Shield (pre-upholstered)
1
Floormat, brake pedal
1
Floormat, left rear pedal
1
Floormat, right rear pedal
1
Push buttons, fasteners
8
Bolt, Hex, ½” x 4 ½”, Gr. 8
2
Wire Loop, 1/4”
2
Front Brackets (NO Loader)
L&R
Bolt, Flange, M12 x 35, YD, Gr. 10.9 (NO Loader)
8
Parts List Optional Components:
Heater
Description
Qty
HS-6 hose clamps
2
Zip Ties, Standard
6
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
Installation Instructions:
1. Remove upper hoop of the two-post ROPS from machine. Take care during installation as
there will be a lot of pressure on the entire assembly.
2. Mark the wires going to both seat switches first, and then disconnect the wiring harness from
both switches.
3.Remove the seat from the seat track assembly tilt. Retain all fastening hardware.
4. Remove the seat track assembly completely from the tractor. Retain all fastening hardware.
5. Remove the toolbox as well as two bolts underneath toolbox. Retain all fastening hardware.
6. Un-bolt the left and right seat belt mounts. Retain hardware for re-installation after cab is
installed. Remove the left side seat belt mechanism from the mount bracket.
7. Take the pre-upholstered under seat shield and roughly position it in the under seat area.
Slide the wiring harness through hole in shield. Slide the upholstery slots around and through
the levers in order to achieve a decent seal under the seat.
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
8. Fasten shield into place with factory hardware at the front first.
9. Re-install the seat track assembly. TIP: When installing M8 bolts, use a small nut (ie 10-24) as
a spacer between the driver socket and the bolt to make installation easier and allow you to put
more pressure down onto the bolt while installing it.
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
10. Re-install the seat onto the seat track assembly with factory hardware.
.
11.For tractors equipped with the LA304 front end loader, take the left front bracket and bolt
to the outside of the loader mount plate shown with the provided 5/8” x 1 ½” hex bolts and
flange nuts. Loosely fasten only. See next photo. Repeat for the right side.
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
12.For tractors equipped with the LA354 front end loader, take the left front bracket and bolt
to the inside of the loader mount plate shown with the provided 5/8” x 1 ½” hex bolts and
flange nuts provided. Loosely fasten only. See photo below. Repeat for the right side.
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
13.For tractors equipped with no loader, take the provided left mounting bracket and four of
M12 x 35 flange bolts and bolt onto the tractor in the bolt pattern shown below:
14.For tractors equipped with no loader, take the provided right mounting bracket and four of
M12 x 35 flange bolts and bolt onto the tractor in the bolt pattern on the right side of the
tractor.
15.Return to the cab to install lift brackets next. To remove the gas shock on the left cab door,
slide a flat screwdriver underneath the small clip on the end cap that must be pulled UP order
to pop the shock off of the ball stud. The shock will release very easily when this is
accomplished. Lift the door assembly straight up and off of the cab and put aside for now.
June 2021© Kubota B2320 Series ROPS Cab Steel Top Installation Manual
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Tractor de Kubota
Kubota
Kubota M108DC Manual de usuario
Kubota
Kubota M5N-091 Manual de usuario
Kubota
Kubota LA525 Manual de usuario
Kubota
Kubota L47TL Manual de usuario
Kubota
Kubota G21LD / G21HD Manual de instrucciones
Kubota
Kubota BX1860 Manual de instrucciones
Kubota
Kubota B1220 Manual de usuario
Kubota
Kubota M5640SU Manual de instrucciones
Kubota
Kubota BX1870 Manual de instrucciones
Kubota
Kubota B1620 Manual de usuario
Kubota
Kubota L4701 Manual de usuario
Kubota
Kubota M100X Manual de usuario
Kubota
Kubota L2501 Manual de usuario
Kubota
Kubota L45 Instrucciones originales
Kubota
Kubota WSM BX1860 Manual de instrucciones
Kubota
Kubota M6800S Manual de instrucciones
Kubota
Kubota Power Krawler M8540 NARROW Manual de instrucciones
Kubota
Kubota L3301 Manual de usuario
Kubota
Kubota WSM B2050 Manual de instrucciones
Kubota
Kubota M6060 Manual de usuario
