KTI Networks KFS-0540 Manual de usuario

-1-

KFS-0540 Ver.B

Industrial 5-Port Fast Ethernet Switch

Installation Guide

DOC.171103

-2-

or by any means or used to make any directive work (such as translation or transformation) without permission

from KTI Networks Inc.

KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to

time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change.

For more information, contact:

United States KTI Networks Inc.

P.O. BOX 631008

Houston, Texas 77263-1008

Phone: 713-2663891

Fax: 713-2663893

E-mail: [email protected]

URL: http://www.ktinet.com/

International Fax: 886-2-26983873

E-mail: [email protected].tw

URL: http://www.ktinet.com.tw/

-3-

The information contained in this document is subject to change without prior notice. Copyright (C) All Rights

Reserved.

TRADEMARKS

Ethernet is a registered trademark of Xerox Corp.

FCC NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) This device must accept any interference received,

including the interference that may cause undesired operation.

CE NOTICE

Marking by the symbol indicates compliance of this equipment to the EMC directive of the European

Community. Such marking is indicative that this equipment meets or exceeds the following technical

standards:

EMC Directive of 2014/30/EU

EN 61000-6-4

EN 55032 Class A

CISPR 32

EN 61000-3-2

EN 61000-3-3

EN 61000-6-2

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-8

IEC 61000-4-11

-4-

Table of Contents

1. Introduction...................................................................................................................................5

1.1 Features..............................................................................................................6

1.2 Product Panels....................................................................................................6

1.3 LED Indicators.....................................................................................................7

1.4 Specifications......................................................................................................7

2. Installation.....................................................................................................................................9

2.1 Unpacking...........................................................................................................9

2.2 Safety Cautions...................................................................................................9

2.3 Mounting the Switch to a Din-Rail......................................................................10

2.4 Mounting the Switch on a Panel........................................................................12

2.5 Applying Power.................................................................................................14

2.5.1 Using Terminal Blocks.................................................................................... 15

2.5.2 Using DC Power Jack ....................................................................................16

3. Making LAN Connections..........................................................................................................17

3.1 10/100 Copper Ports.........................................................................................17

3.2 LED Indication................................................................................................... 17

-5-

1. Introduction

The switch provides five 10/100Mbps copper ports for connections to Ethernet and Fast Ethernet devices. With

the featured auto-negotiation function, the switch can detect and configure the connection speed and duplex

automatically. The switch also provides auto MDI/MDI-X function, which can detect the connected cable and

switch the transmission wire pair and receiving pair automatically. This auto-crossover function can simplify

the type of network cables used.

For industrial environment, the device is designed with the following enhanced features exceeding that of

commercial Ethernet switches:

High and wide operating Temperature

Power input interface: Industrial screw terminal block and DC power jack for external commercial power

adapter as option

Screw panel and DIN rail mounting support for industrial enclosure

Industrial-rated Emission and Immunity performance

-6-

1.1 Features

Auto MDI/MDI-X crossover function on the copper port

Support IEEE 802.3x flow control for full-duplex operation

Support Back-pressure flow control for half-duplex operation

Wide operating temperature range for temperature critical environment

Support DIN-rail mounting and panel mounting

Provide two power input types to meet more application needs

Accept wide power input voltage range for application flexibility

Industrial-rated Emission and Immunity performance

1.2 Product Panels

The following figure illustrates the panels of the switch:

-7-

1.3 LED Indicators

LED Function

POWER Power status

1 - 5 Port 1 –Port 5

LINK Link and activity status (Port 1 - Port 5)

100M 100Mbps speed status (Port 1 - Port 5)

1.4 Specifications

10/100 Copper Ports

Compliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX

Connectors Shielded RJ-45 jacks

Pin assignments Auto MDI/MDI-X detection

Configuration Auto-negotiation or software control

Transmission rate 10Mbps, 100Mbps

Duplex support Full/Half duplex

Network cable Cat.5 UTP up to 100 meters

Switch Functions

Forwarding & filtering Non-blocking, full wire speed

Switching technology Store and forward

Maximum packet length 1536 bytes

MAC Addresses Table 2K entries

Port configuration Auto-negotiation for speed and duplex

Flow control IEEE 802.3x pause frame base for full duplex operation

Back pressure for half duplex operation

Storm control Broadcast packets are dropped when large consecutive broadcast packets are

received.

DC Power Input

Screwed terminal block 3P (Vin+, Vin-, Chassis Ground)

DC Jack Connector -D 6.3mm / + D 2.0mm

Operating Voltages +7 ~ +30VDC

Power Consumption 2.2W max.

Mechanical

Dimension (base) 40 x 80 x 95 mm (WxDxH)

Housing Enclosed metal with no fan

-8-

Mounting Din-rail mounting

Panel mounting (optional)

Environmental

Operating Temperature Typical -35oC ~ +70oC

Storage Temperature -40oC ~ +85oC

Relative Humidity 10% ~ 90% non-condensing

Electrical Approvals

FCC Part 15 rule Class B

CE EN 55032 Class A

EN 61000-6-4

CISPR 32

EN 61000-3-2

EN 61000-3-3

EN 61000-6-2

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-8

IEC 61000-4-11

VCCI Class A

Safety LVD, IEC60950-1

Mechanical Approvals

IEC 60068-2-64 Fh Vibration

IEC 60068-2-6 Fc Vibration 5~200Hz 1G

IEC 60068-2-27 Ea Shock 50G test,

IEC 60068-2-27 Ea Bump 25.5G test

-9-

2. Installation

2.1 Unpacking

The product package contains:

The switch unit for Din-rail mounting

One product CD-ROM

2.2 Safety Cautions

To reduce the risk of bodily injury, electrical shock, fire and damage to the product, observe the following

precautions.

Do not service any product except as explained in your system documentation.

Opening or removing covers may expose you to electrical shock.

Only a trained service technician should service components inside these compartments.

If any of the following conditions occur, unplug the product from the electrical outlet and replace the part

or contact your trained service provider:

- The power cable, extension cable, or plug is damaged.

- An object has fallen into the product.

- The product has been exposed to water.

- The product has been dropped or damaged.

- The product does not operate correctly when you follow the operating instructions.

Do not push any objects into the openings of your system. Doing so can cause fire or electric shock by

shorting out interior components.

Operate the product only from the type of external power source indicated on the electrical ratings label. If

you are not sure of the type of power source required, consult your service provider or local power

company.

-10-

2.3 Mounting the Switch to a Din-Rail

In the product package, a DIN-rail bracket is provided or has been installed for mounting the switch in a

industrial DIN-rail enclosure.

The steps to mount the switch onto a DIN rail are:

1. Install the mounting bracket onto the switch unit with screws as shown below:

2. Attach bracket to the lower edge of the DIN rail and push the unit upward a little bit until the bracket can

clamp on the upper edge of the DIN rail.

Tabla de contenidos

Otros manuales de Cambiar de KTI Networks

KTI Networks

KTI Networks KGS-500 Ver.D Manual de usuario

KTI Networks

KTI Networks KFS-2621 Manual de usuario

KTI Networks

KTI Networks KGS-1064-BP Manual de usuario

KTI Networks

KTI Networks KS-124 Manual de usuario

KTI Networks

KTI Networks KS-108F Manual de usuario

KTI Networks

KTI Networks KGS-2422-TG Series Manual de usuario

KTI Networks

KTI Networks KGS-0841-W Manual de usuario

KTI Networks

KTI Networks KS-108F Manual de usuario

KTI Networks

KTI Networks KGS-2421 Manual de usuario

KTI Networks

KTI Networks KPOE-800-1P Manual de usuario

KTI Networks

KTI Networks KGS-2416 Manual de usuario

KTI Networks

KTI Networks KS-115FM-V Manual de usuario

KTI Networks

KTI Networks KGS-0820 Manual de usuario

KTI Networks

KTI Networks KS-115F Series Manual de usuario

KTI Networks

KTI Networks KS-116 Manual de usuario

KTI Networks

KTI Networks KGS-2404 Manual de usuario

KTI Networks

KTI Networks KGS-2416 Manual de usuario

KTI Networks

KTI Networks KS-801 Manual de usuario

KTI Networks

KTI Networks KS-105F-B Series Manual de usuario

KTI Networks

KTI Networks KGS-510F-C Manual de usuario

KTI Networks

KTI Networks KGS-0800-4HP Manual de usuario

KTI Networks

KTI Networks KS-2402 Manual de usuario

KTI Networks

KTI Networks KGD-802 Manual de usuario

KTI Networks

KTI Networks KS-2240 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario