Kramer VS-88HDxl Manual de usuario

VS-88HDxl Quick Start

P/N:

2900- 301256QS

Rev:

Scan for full manual

VS-88HDxl Quick Start Guide

This guide helps you install and use your VS-88HDxl for the first time.

Go to www.kramerav.com/downloads/VS-88HDxl to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VS-88HDxl 8x8 3G SD/HD-SDI Matrix Switcher

1 Set of rack ears

4 Rubber feet

RC-IR3 IR remote control transmitter

1 Power cord

1 Quick start guide

Step 2: Get to know your VS-88HDxl

Feature

Function

IR Receiver

Receives signals from the IR remote control transmitter. Lights yellow when receiving

signals.

POWER LED

Lights when the unit is ON.

ALL Button

Press ALL and then press an IN button to connect the selected input to all outputs.

OFF Button

Press OFF + OUT to disconnect the selected output from the inputs.

Press OFF + ALL to disconnect all outputs.

Press and hold OFF to toggle between dual link and normal mode.

IN SELECT Buttons

Press to select the input to switch to the output.

Press and hold buttons IN1 to IN5 to change the genlock timing (see Step 4)

OUT SELECT Buttons

Press to select the output to which the input is switched.

STO (STORE) Button

Press STO and then press an IN/OUT SELECT key to store the current setting.

RCL (RECALL) Button

Press RCL and the relevant IN/OUT SELECT key to recall a setup from the non-volatile

memory.

LOCK Button

Press and hold for three seconds to disable/enable the front panel buttons.

TAKE Button

Press to confirm a command in Confirm mode (see Step 6).

7-segment INPUT Display

Displays each input under the output number that it is switched to.

GENLOCK BNC Connector

Connect to the genlock source.

TERM HI-Z/75Ω Pushbutton

Press to terminate the genlock source (75Ω) or release for looping.

LOOP BNC Connector

Connect to the genlock connector of the next unit in the line.

INPUT BNC Connectors

Connect to the serial digital video sources.

RS-232 9-pin D-sub (F) Port

Connect to a PC or a control device.

Feature

Function

PROG/RS-485 TERM

DIP Switches

PROG DIP switch enables microcontroller firmware upgrade.

RS-485 TERM DIP switch terminates the RS-485 line with a 120Ω load.

RS-485 Terminal Block Port

Connect to a RS-485 control device (see Step 4).

ETHERNET RJ-45 Connector

Connects to a PC or other serial controller through computer networking LAN.

MACH # DIP Switches

Use the set the Machine number of the unit (see Step 4).

ETH RESET Button

Press to reset to factory default definitions:

IP number −192.168.1.39, Mask –255.255.0.0, Gateway –0.0.0.0

OUTPUT BNC Connectors

Connect to the serial digital video acceptors.

REMOTE IR 3.5mm Mini Jack

Connect to an external IR receiver unit for controlling the machine via an IR remote control

(instead of using the front panel IR receiver).

Power Connector with Fuse

Connect to the electricity mains using the power cord.

Power Switch

Turns the power to the unit ON and OFF.

Step 3: Mount VS-88HDxl

To rack mount the machine, attach both rack ears

(by removing the screws from each side of the

machine and replacing those screws through the

rack ears) or place the machine on a table.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-88HDxl.

RS-232 Connection:

Use a 9-wire straight cable and connect only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5 to the RS-232 9-pin D-sub port on

your PC. Note: A null-modem adapter/connection is not required.

RS 485 Connection:

You can operate the VS-88HDxl via the RS-485 port from a distance of up to 1200m (3900ft).

To connect a control device with a RS-485 port to the VS-88HDxl:

1. Set the VS-88HDxl RS-485 machine number and bus termination.

2. Connect the A (+) pin, B (–) pin, and G pin on the RS 485 port of the PC to the corresponding pins on the RS 485 port

on the rear panel of the VS-88HDxl. Note: Pin G may be connected to the shield, if required.

Setting the Machine Number:

•When using a single VS-88HDxl unit, set the unit to Machine # 1.

•When connecting more than one VS-88HDxl unit set a unique Machine # for each unit. The units do not have to be

numbered sequentially. The master unit must be set to Machine #1.

To set the machine # for each unit, set the DIP switches according to the relevant row in the following table:

Machine #

DIP-SWITCH

1 (Single or master

unit)

OFF or ON

OFF

Note: After changing the machine #, the unit must be reset by turning it OFF and ON.

Setting the RS-485 Line Termination:

The RS-485 TERM DIP switch on the first and last units on the RS-485 line must be set to

ON (terminated) and all other units must be set to OFF (not terminated).

Note: The master unit may be located at any part of the line.

Setting the Genlock Video Signals:

To set the Genlock video signals according to timing of the Genlock reference input:

1. Connect the Genlock cable.

2. Press and hold, for 3 seconds, the relevant IN SELECT button according to the table:

IN SELECT Button

Genlock Setting

1080i/p @60Hz

1080i/p @50Hz

720p @60Hz

PAL @50Hz

NTSC @60Hz

The Genlock setting changes and the new setting is displayed in the INPUT display.

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/VS-88HDxl.

Using third-party cables may cause damage!

Step 5: Connect power

Connect the power cord to VS-88HDxl and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 6: Operate VS-88HDxl

IR remote control:

RS-232/RS-485 and Ethernet:

RS-232

Protocol 2000

Protocol 3000

Baud Rate:

9600

Baud Rate:

115200

Data Bits:

Stop Bits:

Parity:

None

Parity:

None

Command Format:

HEX

Command Format:

ASCII

Example: (Switch video input 2 to output 4):

#V 2>4<CR>

Switching Protocol

P2000 -> P3000

P3000 -> P2000

Command:

0x38, 0x80, 0x83, 0x81

Command:

#P2000<CR>

Front Panel:

Press and hold LOCK and OUT 3

simultaneously

Front Panel:

Press and hold LOCK and OUT 2

simultaneously

Default Ethernet Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.0.0

TCP Port #:

5000

Default gateway:

0.0.0.0.

Power On Display:

When VS-88HDxl is powered on, the display briefly shows the 4-

digit firmware version number and the genlock timing setting

before showing the normal operating display.

Opration Modes:

VS-88HDxl can operate in the following two modes:

•At Once –pressing buttons on the front panel

immediately executes a command.

•Confirm –pressing buttons on the front panel does not

execute a command until the TAKE button is pressed,

to protect against incorrect switching. The mode also

enables keying in several commands and then,

simultaneously executing them by pressing the TAKE

button.

To toggle between At Once and Confirm modes, press the TAKE

button when there are no commands pending.

Note: The TAKE button remains lit in Confirm mode.

To simultaneously execute several commands in Confirm mode:

1. Press the required OUT-IN combinations in sequence.

The INPUT display flashes.

2. Press the TAKE button to confirm all the actions.

The actions are executed and the 7-segment display stops

flashing.

Storing Configurations:

You can save up to 16 input/output configurations in the

VS-88HDxl memory and load them as presets.

To save the current configuration:

1. Press the STO button.

The STO button flashes.

2. Press one of the IN/OUT SELECT buttons.

The current configuration is saved in the memory for the

selected button.

To load an input/output configuration:

1. Press the RCL button.

The RCL button flashes.

2. Press the IN/OUT SELECT button that corresponds to the

required configuration.

The selected preset configuration is loaded from memory.

Note: Recalling an invalid preset activates an error indication (the

STO, RCL, LOCK, and TAKE buttons flash).

If you cannot remember which of the IN/OUT SELECT buttons

corresponds to the required configuration, set VS-88HDxl to

Confirm mode and manually scan all the configurations until you

locate it.

Otros manuales para VS-88HDxl

Tabla de contenidos

Otros manuales de Conmutador de matriz de Kramer

Kramer

Kramer VSM-4x4X Manual de usuario

Kramer

Kramer MV-4X Manual de usuario

Kramer

Kramer VP-4x8 Manual de usuario

Kramer

Kramer VS-88H Manual de usuario

Kramer

Kramer VS-88DVI Manual de usuario

Kramer

Kramer LASSEN XL 3216S Manual de usuario

Kramer

Kramer VS-3232DN-EM Manual de usuario

Kramer

Kramer VS-622DT Manual de usuario

Kramer

Kramer XL 1204V Manual de usuario

Kramer

Kramer VS-88HD Manual de usuario

Kramer

Kramer 3232S Manual de usuario

Kramer

Kramer VS-84HDCPxl Manual de usuario

Kramer

Kramer VP-32XLN Manual de usuario

Kramer

Kramer VS-66HN Manual de usuario

Kramer

Kramer VS-48HDCPxl Manual de usuario

Kramer

Kramer VS-81HD Manual de usuario

Kramer

Kramer VP-211DS Manual de usuario

Kramer

Kramer VS-6464DN-EM Manual de usuario

Kramer

Kramer VP-778 Manual de usuario

Kramer

Kramer VP-23RC Manual de usuario

Kramer

Kramer VP-729 Manual de usuario

Kramer

Kramer VS-84HDCPxl Manual de usuario

Kramer

Kramer VS-42HDMI Manual de usuario

Kramer

Kramer Sierra Pro XL 1608V3 Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Roland

Roland XS-1HD Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario

Extron electronics

Extron electronics MTPX Plus Series Manual de usuario

Key Digital

Key Digital Champion KD-16x16CS Manual de usuario

Shinybow USA

Shinybow USA SB-8811 Manual de usuario

Optimus

Optimus Compact Manual de usuario