Kramer VS-6464DN-EM Manual de usuario

VS-6464DN-EM Quick Start

P/N:

2900- 301386QS

Rev:

Scan for full manual

VS-6464DN-EM Quick Start Guide

This guide helps you install and use your VS-6464DN-EM for the first time.

Go to www.kramerav.com/downloads/VS-6464DN-EM to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VS-6464DN-EM 8x8 to 64x64 Modular Multi-Format Managed

Digital Matrix Switcher

1 Power cord

1 Quick start guide

Infrared remote control transmitter with batteries (for future use)

1 Set of rack ears (attached)

Step 2: Get to know your VS-6464DN-EM

Feature

Function

Double-

function

Selector

Buttons

Area

Button

Functions

ESC

Press to exit the current operation.

EDID

Press to assign EDID channels.

STO

Press to store the current setup in a preset. After pressing the MENU button, this button

lights and is enabled.

ALL

Press to connect an input to all outputs. After pressing the MENU button, this button lights

and is enabled.

OFF

Press to turn off an output. After pressing the MENU button, this button lights and is

enabled.

RCL

Press to recall a preset. After pressing the MENU button, this button lights and is enabled.

DELAY

Press to set the delay between confirming an action and the execution of the action.

ENT

Press to complete the input-output setup when using a one-digit number instead of two

digits. For example, to enter input 5, you can press either 05 or 5, ENT.

Press to enter the options in a setup menu.

Feature

Function

IR Receiver

Infrared remote control sensor (for future use).

IR LED

Lights yellow when receiving commands from the IR remote control transmitter (for future

use).

TAKE Button

Press to confirm actions.

MENU Button

Press once to enable the ALL, OFF, STO and RCL buttons.

Press again to enter the configuration menu.

When in a Menu, press to cycle through the menu items.

LOCK Button

Press and hold for approximately 2 sec to lock/unlock the front panel buttons.

BREAKAWAY Button

Press to exit a menu.

DEFAULT SETUP Button

Press to recall the default setup.

OUTPUTS/INPUTS

LCD Display

Displays the outputs (upper row) switched to the selected inputs (lower row).

Displays user interface messages and menus.

Power Supplies

Supply power to the device. The unit includes two power supplies. A third one can be

installed.

◄(Backward)

Press to shift the sliding window to the right (the LCD display only shows 13 cross-points

out of a total of 16).

1, 2, 3, 4, 5, 6, 7, 8, 9, 0

Numeric keypad, 1 to 0.

►(Forward)

Press to shift the sliding window to the left (the LCD display only shows 13 cross-points

out of a total of 16).

Feature

Function

Video Generator Output Connector

Connect to one of the relevant video inputs to aid in troubleshooting.

PATTERN Button

Press the button repeatedly to change the video pattern generated by the video

generator.

RESOLUTION DIP-switches

Set the resolution for video patterns generated by the video generator.

AUDIO OUT / IN 3.5mm Mini Jacks

Connect an audio source and speakers for testing the unit.

IN 1~32 Connectors

Connect to the relevant video sources, depending on the cards installed (1 to 32).

IN 33~64 Connectors

Connect to the relevant video sources, depending on the cards installed (33 to 64).

USB Virtual COM Port

USB Mini-B Connector

Connect to a PC or remote controller and perform firmware upgrade of the device

and compatible input/output cards.

Feature

Function

RESET Button

For future use.

AC Mains Power Module

Connect to the power cord and mains electricity. The fuse protects the unit and the

switch is for turning the unit on and off.

RS-232 9-pin D-sub Port

Connect to a PC or remote controller and perform firmware upgrade of the device

and compatible input/output cards.

NET Ethernet RJ-45 Connector

Connect to a PC or controller via the Ethernet LAN and perform firmware upgrade of

the device and compatible input/output cards.

The LINK LED flashes when communication is active. POWER LED lights when the

interface receives power.

OUT 1~32 Connectors

Connect to the relevant video acceptors, depending on the cards installed (1 to 32).

OUT 33~64 Connectors

Connect to the relevant video acceptors, depending on the cards installed (33 to 64).

Step 3: Install the VS-6464DN-EM

To rack mount the machine, the VS-6464DN-EM is pre-assembled with

ear brackets attached to the machine.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-6464DN-EM. For best results, we recommend

that you always use Kramer high-performance cables to connect AV equipment to the VS-6464DN-EM.

Note: the maximum number of ports may vary.

Port Numbering:

On each card there are eight physical ports numbered sequentially from top to bottom and left to right.

Note: The diagram below is a sample numbering showing only the bottom of each card.

Diagram #

Actual Port #

IN 1 –IN 8

IN 9 –IN 16

IN 17 –IN 24

OUT 1 –OUT 8

OUT 9 –OUT 16

OUT 17 –OUT 24

Step 5: Connect the power

Connect the power cord to VS-6464DN-EM and plug it into the mains electricity. Switch the VS-6464DN-EM power and then

switch on the power of connected devices.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 6: Set operation parameters

VS-6464DN-EM includes a front panel numeric

keypad for routing and control.

On power up, the last used matrix setup is loaded. To

retrieve other setups, use setup recall for a stored

configuration or default setup recall.

The LCD display can show only 13 out of the 64

available matrix combinations at once. To view any of

the matrix combinations use the ◄ or the ► buttons.

On power up, the display shows the following screens in

sequence:

Step 7: Operate via front panel buttons, RS-232, or web pages via Ethernet

RS-232 Control / Protocol 3000

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

HEX

Stop Bits:

Example: (Switch video input 4 to output 2): #VID 4>2

Default Ethernet Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet mask:

255.255.255.0

TCP Port #:

5000

Default User:

Admin

Default Password:

Admin

Concurrent TCP Connections:

Full Factory

Reset

Press front panel MENU button twice. Select

Total Matrix Reset > Factory Reset. Press

TAKE twice.

Otros manuales para VS-6464DN-EM

Otros manuales de Conmutador de matriz de Kramer

Kramer

Kramer VS-6YC Manual de usuario

Kramer

Kramer Sierra Video 6432V5Sxl Manual de usuario

Kramer

Kramer Sierra Video 1608V3S Manual de usuario

Kramer

Kramer VS-88HN Manual de usuario

Kramer

Kramer VP-16x18AK Manual de usuario

Kramer

Kramer MTX3-16-M Manual de usuario

Kramer

Kramer VS-44HN Manual de usuario

Kramer

Kramer VS-401YC Manual de usuario

Kramer

Kramer XL 1616V4 Manual de usuario

Kramer

Kramer VS-66H3 Manual de usuario

Kramer

Kramer VS-1616DN-EM Manual de usuario

Kramer

Kramer VS-44HD Manual de usuario

Kramer

Kramer VS-88UHDA Manual de usuario

Kramer

Kramer VS-88UHDA Manual de usuario

Kramer

Kramer VP-4x8 Manual de usuario

Kramer

Kramer Sierra Pro XL 1616V3S Manual de usuario

Kramer

Kramer VS-48H Manual de usuario

Kramer

Kramer VS-44AV Manual de usuario

Kramer

Kramer VP-32K Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer 1608HD Manual de usuario

Kramer

Kramer Sierra Video 1616V5S Manual de usuario

Kramer

Kramer Sierra Pro XL 1608V5S Manual de usuario

Kramer

Kramer VS-806YC Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Roland

Roland XS-1HD Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario

Extron electronics

Extron electronics MTPX Plus Series Manual de usuario

Key Digital

Key Digital Champion KD-16x16CS Manual de usuario

Shinybow USA

Shinybow USA SB-8811 Manual de usuario

Optimus

Optimus Compact Manual de usuario