Kozyard Atlantis Manual de usuario
Atlantis Aluminum 10’x13’ Pergola
Assembly Manual
Kozyard LLC Products
www.kozyard.com
© Copyright 2016 - 2019 Kozyard LLC. | All Rights Reserved.
3+
Use the hex keys in the box.
You may need to use a drill for this step.
You may need a ladder.
Three or more people are required at this stage.
Do not tighten screws all the way for now.
Page 1
Page 2
4X 2X
1X2X
1X
2X 2X
1X 1X
2X 2X
1X 1X
5X 5X
4X
1X
1X
8X
1X 1X
Page 3
4X 5X
OVERALL
Page 4
Connect A and A1 or A2 by using supporting part V and bolt J to
build the four poles (2xA&A1 and 2xA&A2).
Connect Part I and 4 poles by using bolt J
Tight bolt J after A connected with A1 or A2 vertially.
A
A
A
A
A1
A2
A2
A1
J
J
I
A
I4X
J16X
S4
M6x16
Q1X
Step 2
A4X
A1 2X
A2 2X
J64X
S4
M6x16
Q1X
Step 1
A
A1 or A2
J
J
A1
Vor A2
J
J
V8X
Don't tight the bolts too much when you insert A into A1 or A2.
Page 5
Step 3
B
B1
B
B2
J
J
C
C1
B1X
B1 1X
R2X
J32X
Q1X
M6x16
S4
B2
B2
C2
1X
1X
V1 4X
C2
V1
J
J
B2
B1
J
J
V1
J
J
C2
C1
J
J
V1
J
J
C
C2
J
J
V1
J
J
R
R
C1X
C1 1X
Connect B , B1 and B2 by using supporting part V1
and bold J to build the main beam 1 .
Connect C, C1 and C2 by using supporting part V1
and bold J to build another main beam 2.
Page 6
A
A2
A
A1
A
A2
A
A1
B
B1
C
C2
M
B
A2
D
D
E
E
M16X
Q1X
S6
M6x15
N
N
O
O
P
D2X
E1X
N10X
O4X
PP
1X
Step 4
Step 5
B2
C1
&B1
A1 &
Connect the main beam 1 and main beam 2 with
the four poles using bolt M.
1. Insert the hook into the slot of part D,
Repeat twices.
2. Insert the hook P and hook O into
the slot of part E.
Please insert the hook P by this
way.Don’t insert the hook P
opposite way as diagram!
Attention: Always keep hook P and
C1/C2 in the same side.of part E.
X5
X1
X4
2X
2X
16X
M6x16
S4
1X
16X
M6x15
1X
S6
Page 7
Step 6
Step 7
2X
Connect D and D1 to build the cross beam (D&D1) by using bolt J
and supporting part V2
Connect the cross beam (D&D1) with the four poles
using bolt M.
D
D
D
D
D
D
D1
D1
D1
D1
A1
B1
D1
V2
V2
J
J
J
J
J
Q
M
M
Q
1X
1X
2X
2X
24X
M6x16
S4
1X
6X
M6x85
S4
1X
Page 8
Step 8
Step 9
3X
or
or
1. Connect E and E1 by
using supporting
part V2
and bold J to build
the cross beam (E&E1).
2. Using the same method
as the last step, use F and
F1 to build the cross
beam (F&F1).
Connect the cross beam (E&E1) and (F&F1)
with the main beam 1 and 2.
Attention: Always keep hook P and C1/C2 in the same side.
E
E
E
E
E1
E1
E1
E1
F
F
F
F
F1
F1
F1
F1
V2 V2
V2
J
J
J
J
J
J
J
J
J
Q
LL
L
Q
Insert G, G1, H, H1 into the canopy from its side
G
G1
H
H1
H
G1X
G1 1X
H5X
H1 5X
S1X
S
S
K3X
M6x30
S4
Q1X
K
G1
B1
J10X
M6x16
J
H
H1
Step 10
Step 11
G&
B&
Connect G&G1 and B&B1 by bolt K, and hold the
canopy with the frames.
Connect the canopy and
the hock using bolt J
Connect H and H1 through the hook
Page 9
Pull the line from the canopy and put on hook
to tighten the canopy.
Otros manuales de Carpa de Kozyard
