Konica Minolta CS-3000HDR Manual de usuario

SPECTRORADIOMETER

CS-3000HDR / CS-3000 / CS-2000Plus

Instruction Manual

Please read before using

the instrument.

Safety Symbols

The following symbols are used in this manual to prevent accidents which may occur as a result of

incorrect use of the instrument.

Denotes a sentence regarding a safety warning or caution.

Read the sentence carefully to ensure safe and proper use of

the instrument.

Denotes a prohibited operation.

The operation must never be performed.

Denotes an instruction.

The instruction must be strictly adhered to.

Denotes an instruction.

Disconnect the power plug from the AC outlet.

Denotes a prohibited operation.

Never disassemble the instrument.

Denotes alternating current (AC).

Denotes direct current (DC).

Denotes class II protection against electric shock.

Notes on This Manual

Copying or reproduction of all or any part of the contents of this manual without KONICA MINOLTA’s

permission is strictly prohibited.

The contents of this manual are subject to change without prior notice.

Every effort has been made in the preparation of this manual to ensure the accuracy of its contents.

However, should you have any questions or find any errors or omission, please contact the nearest

KONICA MINOLTA-authorized service facility.

KONICA MINOLTA will not accept any responsibility for consequences arising from the use of the

instrument.

Safety Precautions

To ensure correct use of the instrument, read the following points carefully and adhere to them. After

you have read this manual, keep it in a safe place where it can be referred to anytime a question arises.

Warning (Failure to adhere to the following points may result in death or serious

injury)

Do not use this instrument in places where flammable or combustible gases (gasoline,

etc.) are present.

Doing so may cause fire.

Do not use this instrument when the inside is dirty with dust that has entered through the

ventilation holes. Doing so may cause fire. For periodic inspections, please contact the

nearest KONICA MINOLTA-authorized service facility.

Always use the AC adapter (AC-A312G) supplied as a standard accessory and connect it to

an indoor AC outlet of rated voltage and frequency (100-240 V , 50 Hz/60 Hz). Use of an

AC adapter other than the one specified or connection to a different voltage may result in

damage to the instrument, fire or electric shock.

Fully insert the power plug until it is securely seated in the AC outlet. Failure to do so may

result in fire or electric shock.

If this instrument is not used for a long time, disconnect the AC adapter from the AC outlet.

Accumulated dirt or water on the prongs of the AC adapter may cause fire. Accumulated

dirt or water on the prongs of the AC adapter may cause fire and should be removed.

When unplugging the power cord of the AC adapter, gently unplug it by holding the power

plug. Do not forcibly pull the power cord when unplugging as this may damage it or cause

fire or electric shock. Also, do not handle the power cord with wet hands.

Doing so may cause electric shock.

Do not forcibly bend, twist or pull the power cord. Also, do not place heavy objects on the

power cord, or damage or modify it. Such actions may cause fire or electric shock due to

damage to the power cord.

Do not disassemble or modify this instrument or the AC adapter. Doing so may cause fire

or electric shock.

Do not spill liquid on this instrument or drop metallic objects onto it. Doing so may cause

fire or electric shock. Should either of these happen, immediately switch the power off and

unplug the AC adapter, and then contact the nearest KONICA MINOLTA-authorized

service facility.

Should this instrument or the AC adapter be damaged or emit smoke or an odd smell, do

not keep using such instrument or AC adapter without correction. Doing so may cause fire.

In such situations, immediately switch the power off and unplug the AC adapter, and then

contact the nearest KONICA MINOLTA-authorized service facility.

Do not look at the sun or intense light through the finder of this instrument. Doing so may

cause loss of sight.

Caution

Use the instrument near an AC outlet so that the AC adapter can be easily plugged and

unplugged.

Do not place the instrument on an unstable or sloping surface. Doing so may cause it to

drop or overturn, resulting in injury. Take care not to drop the instrument when carrying it.

Do not move while looking inside the finder. as it may cause an accident such as the user

falling over.

Take special care when handling the ND filter or closeup lens included in the optional

accessories. Breakage of the ND filter or closeup lens may cause injury.

Take care not to get your hand caught in the opening and closing parts of the storage case

included in the optional accessories as this may cause an injury.

Keep the instrument’s ventilation holes free from obstruction.

Failure to do so may cause fire.

Unplug the power plug from the AC outlet when cleaning the instrument.

Failure to do so may cause electric shock.

(Failure to adhere to the following points may result in injury or

damage to the instrument or other properties)

Introduction

This instrument is a high-accuracy spectroradiometer designed to measure luminance and chromaticity

up to super-low luminance regions. Carefully read this manual before using it.

Packaging materials

Be sure to save all packaging materials (corrugated cardboard boxes, pads and plastic bags)

supplied with the purchase. This is a precision measuring instrument. Use supplied packaging

materials to minimize shocks and vibrations in case this instrument needs to be transported for

purposes such as maintenance in KONICA MINOLTA’s factories.

Should any of these packaging materials be lost or broken, please contact the nearest

KONICA MINOLTA-authorized service facility.

Notes on Use

Be sure to use this instrument properly. Use of this instrument in ways other than those specified in this

manual may result in risk of injury, electric shock, instrument damage, or other problems.

Operating Environment

The AC adapter (AC-A312G) supplied as a standard accessory is designed specifically for use

indoors. Do not use it outdoors.

Do not disassemble this instrument as it is composed of precision electronic components.

Use this instrument at rated voltage of 100-240 V . Connect the AC power cord to the AC outlet

with the rated voltage and frequency of 100-240 V (50/60 Hz). Connected voltage should not be

outside the range of ±10% of nominal.

This instrument corresponds to a Pollution Degree 2 product (instruments used mainly in

manufacturing plants, laboratories, warehouses or equivalents.). Use the instrument in

environments not exposed to metallic dust and condensation.

This instrument corresponds to an Overvoltage Category I product (instruments connected to a

circuit with measures taken to limit excessive overvoltage to a suitably low level).

This instrument and the AC adapter are EMC Class B products. Use of the instrument and the AC

adapter in home environments may cause radio interference. Users may be required to take

appropriate measures in such cases.

This instrument complies with Electrical equipment for measurement, control and laboratory use - EMC

(Electromagnetic Compatibility) requirements - Part 1: General requirements (EU Harmonized

Standards EN 61326-1:2021). Conformity verification is performed under KONICA MINOLTA’s test

conditions in an INDUSTRIAL ELECTROMAGNETIC ENVIRONMENT specified in the relevant

harmonized standards. The limit of performance degradation when subjected to continuous disturbance

during immunity testing is up to twice KONICA MINOLTA’s repeatability specifications (Lv, x, y).

Take care not to allow foreign substances like water and metal to penetrate the instrument.

Operating it in such a state is extremely dangerous.

Do not use this instrument in places exposed to direct sunlight or near a heating appliance. Doing so

may cause the internal temperature of the instrument to greatly exceed the ambient temperature,

which may break the instrument. Also, use the instrument in a well-ventilated place. To ensure

proper heat dissipation, keep the ventilation holes free from obstruction.

Avoid a rapid change in ambient temperature to prevent condensation.

Avoid using the instrument in extremely dusty or humid places.

Use the CS-2000Plus at an ambient temperature between 5 and 35ºC and relative humidity of 80%

or less (at 35ºC) with no condensation. Use the CS-3000HDR/CS-3000 at an ambient temperature

between 5 and 30ºC and relative humidity of 80% or less (at 30ºC) with no condensation. Operating

the instrument outside the specified temperature and humidity ranges may impede its performance.

Do not use the instrument at altitudes higher than 2,000 m above sea level.



Make sure the AC adapter output plug is not short-circuited. A short-circuit may cause fire or electric shock.

Do not connect the AC adapter to an overloaded electrical circuit. In addition, do not cover or wrap

the AC adapter with cloth or any other material while in use. Doing so may cause electric shock or fire.

When removing the AC adapter from the instrument, first remove the power cord from the outlet,

and then remove the output plug.

This Instrument

Do not subject the instrument to strong impact or vibration.

Do not forcibly pull, bend, or apply strong force to the power cord for the included AC adapter or

USB cable. This may result in the cord snapping.

Connect the instrument to a power source with minimal noise.

Do not measure a high-luminance light source (including sunlight) beyond the measurement range.

Failure to observe this warning could result in damage to the instrument’s optical system.

Should you notice any breakage or abnormality during operation, immediately switch the power off

and unplug the AC adapter. Then refer to “Error Check.” p.98

Should this instrument break down, do not try to disassemble and repair it by yourself. Please

contact the nearest KONICA MINOLTA-authorized service facility.

Warm this instrument up for at least 20 minutes after switching the power on when the object

luminance is 2 cd/mor lower (measurement angle 1º).

When not using RS-232C communication, be sure to attach the connector cap. Failure to do so may

cause malfunction due to static electricity.

Objective Lens, ND Filter, Closeup Lens, and Illuminance Adapter (Optional Accessories)

When performing measurements, make sure that the surfaces of the objective lens, ND filter,

closeup lens, and illuminance adapter (optional accessories) are clean. Correct measurement may

not be performed if there is dirt, dust, fingerprints or parts left unclean.



Do not touch the surface of objective lens, ND filter, closeup lens or illuminance adapter with your hands.

When a sudden change in temperature is applied in a high humidity environment, this may mist the

objective lens, ND filter, closeup lens or illuminance adapter, resulting in incorrect measurements.

Please note that observing light of about 100,000 lx with a light source with a large infrared light

output, such as an A light source, may cause a large temperature rise inside the illuminance adapter

and the main unit, resulting in damage.

Notes on Storage

Main Unit



Do not store this instrument in places exposed to direct sunlight or near a heating appliance. Doing so may cause

the internal temperature of the instrument to greatly exceed the ambient temperature, leading to malfunction.

Store this instrument at an ambient temperature between 0 and 35ºC and relative humidity of 80%

or less (at 30ºC) with no condensation. Storage under high temperature and humidity may impede

the performance of this instrument, so we recommend storage with a drying agent at room

temperature.

Take care to prevent condensation forming when storing the instrument. Also, when moving the

instrument to a location where it will be stored, be careful of sudden temperature changes to avoid

condensation.

Insert the instrument in the packaging box supplied at purchase or the storage case (CS-A30) in the

optional accessories and store in a safe place.

Objective lens

When storing the objective lens, cover them with the standard accessory lens cap.

Cleaning

Main Unit

If the instrument becomes dirty, wipe it with a dry and soft cloth. Do not use an organic solvent, such

as benzine or thinner, or any other chemical agent to clean it. Should none of these methods remove

the dirt, please contact the nearest KONICA MINOLTA-authorized service facility.

Objective lens

Should dirt or dust get on the lens, wipe it off with a dry and soft cloth or lens cleaning paper. Do not

use an organic solvent, such as benzine or thinner, or any other chemical agent to clean it. Should the

dirt be difficult to remove, please contact the nearest KONICA MINOLTA-authorized service facility.

Notes on Transporting

Use the packaging material supplied at purchase to minimize vibration or shocks generated while

transporting the instrument.

Put all materials including the main unit and accessories in the original packaging material when

returning the instrument for servicing.

Maintenance

Periodic maintenance is recommended annually to maintain measurement accuracy of the instrument.

For details on maintenance, please contact the nearest KONICA MINOLTA-authorized service facility.

Disposal Method

Make sure that the main unit, its accessories and the packing materials are either disposed of or

recycled correctly in accordance with local laws and regulations.

Safety Symbols ...................................... ii

Introduction .......................................... 3

Notes on Use ............................................ 3

Operating Environment ............................................3

This Instrument.........................................................4

Objective Lens, ND Filter, Closeup Lens, and

Illuminance Adapter (Optional Accessories)..............4

Notes on Storage ...................................... 5

Main Unit..................................................................5

Objective lens...........................................................5

Cleaning................................................... 5

Main Unit..................................................................5

Objective lens...........................................................5

Notes on Transporting .............................. 5

Maintenance ............................................ 5

Disposal Method ...................................... 5

Standard Accessories............................. 8

Optional Accessories.............................. 9

System Configuration .......................... 11

Names and Functions of Parts............... 12

Names of Each Part................................. 12

Functions of Each Part............................. 13

Key Panel ............................................... 14

Main Functions of Each Key ..................... 14

Diopter Adjustment................................ 15

LCD Screen ............................................. 16

MEAS (Measurement Value) Screen ........................16

MENU Screen .........................................................17

Installation

Installing ............................................. 20

Connecting AC Adapter ........................ 21

Connection Method ................................ 22

Power supply ON ( | ) / OFF (O) ............. 23

Turning Power Switch ON .......................................23

Turning Power Switch OFF ......................................23

Setting

Selecting Measurement Speed ............. 26

Setting of Synchronization ................... 31

Emission Frequency Detection and Setting

Function (CS-3000HDR/CS-3000 only).......... 34

Vertically Synchronized Signal Input

Method .................................................. 36

Selecting Synchronous Frames............. 38

Selecting Measurement Angle .............. 40

Selecting Color Matching Functions...... 42

Selecting Display Format...................... 44

Process Settings for Negative Spectral

Radiance Values ..................................... 46

Selecting Color Space........................... 48

Using the Closeup Lens ........................ 50

Using the ND Filter ............................... 52

Using the Illuminance Adapter ............. 54

Backlight ON/OFF During

Measurement ...................................... 56

Baud Rate Selection for RS-232C

Communication ................................... 58

Setting RS-232C Power Supply ............. 60

Setting Internal Clock........................... 62

Setting Periodic Calibration Reminders ... 64

Contents

Calibration........................................... 66

Calibration Channels .............................. 66

Checking Main Unit Information ........... 68

Measurement

Measurement ...................................... 70

Saving Measurement Values................. 73

Confirming Memory Data ..................... 76

Deleting Memory Data ......................... 77

Communication

Connecting to a PC ............................... 82

Connection via USB cable........................ 82

Connection via RS-232C cable................. 83

Connection via RS-232C Bluetooth

Conversion Adapter................................ 84

Remote Mode ...................................... 85

Explanation

Measurement Principles....................... 88

Sensor Section........................................................88

Dark Measurement .............................. 89

Dark measurement modes......................................89

Performing Dark Measurement...............................90

LvTcpΔuv ............................................. 91

Dominant Wavelength/

Excitation Purity .................................. 92

Dimensions.......................................... 93

Error Messages .................................... 96

Caution Messages................................ 97

Error Check.......................................... 98

Setting Initialization .......................... 101

Main Specifications............................ 102

Standard Accessories

Lens Cap CS-A31

Attach it to the objective lens to protect them when

not using this instrument.

USB Cable (2 m) CS-A32

Used for communication between the instrument

and a PC.

AC Adapter AC-A312G (ATS036T-A120)

Supplies power from the AC outlet.

Input: 100 V - 240 V~ 50/60 Hz 1 A Max

Output: 12 V 3 A

Plug design Center-negative

Screw for focus ring lock CS-A38

Locks the focus adjustment ring so that it does not

move unintentionally.

Do not use any screw other than the provided one.

Should it get lost or damaged, purchase a new CS-A38 screw.

When shipped from the factory, this screw holds the focus adjustment ring in place. To move the focus

adjustment ring, loosen this screw.

When storing the CS-3000HDR/CS-3000/CS-2000Plus in the Storage Case (optional accessory), remove

this screw or position it so that it does not hit the packing material.

When inserting the CS-3000HDR/CS-3000/CS-2000Plus in the packaging for transportation, remove this

screw or position it so that it does not hit the packing material.

Calibration Certificate

Software for Spectroradiometers

CS-S30

This software allows the instrument to be controlled

and perform versatile data management from a PC.

Software can be downloaded from https://www.

konicaminolta.com/instruments/download/software/

display/index.html.

Standard and optional accessories are available with the instrument.

Memo The shapes of some products may be different from those shown.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Konica Minolta

Konica Minolta

Konica Minolta bizhub C3100i Manual de usuario

Konica Minolta

Konica Minolta Vivid 910 Manual de usuario

Konica Minolta

Konica Minolta CM-3700D Manual de usuario

Konica Minolta

Konica Minolta CHROMA METER CS-200 Manual de usuario

Konica Minolta

Konica Minolta CA-410 Series Manual de usuario

Konica Minolta

Konica Minolta CM-36dGV Manual de usuario

Konica Minolta

Konica Minolta CR-10 Plus Manual de usuario

Konica Minolta

Konica Minolta CM-2600d Manual de usuario

Konica Minolta

Konica Minolta JM-103 Manual de usuario

Konica Minolta

Konica Minolta CA-210 Manual de usuario

Konica Minolta

Konica Minolta FD-5 Manual de usuario

Konica Minolta

Konica Minolta SPECTRAMAGIC NX - Manual de usuario

Konica Minolta

Konica Minolta VIVID 9i Manual de usuario

Konica Minolta

Konica Minolta AeroDR System Manual de usuario

Konica Minolta

Konica Minolta CM-25cG Manual de usuario

Konica Minolta

Konica Minolta CA-410 Series Manual de usuario

Konica Minolta

Konica Minolta SPAD-502 PLUS Manual de usuario

Konica Minolta

Konica Minolta CM-36d Manual de usuario

Konica Minolta

Konica Minolta CM3600D Manual de usuario

Konica Minolta

Konica Minolta CM-26dG Manual de usuario

Konica Minolta

Konica Minolta CM-25cG Manual de usuario

Konica Minolta

Konica Minolta CR-14 Manual de usuario

Konica Minolta

Konica Minolta Vivid 910 Manual de usuario

Konica Minolta

Konica Minolta REGIUS 110 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario