Kollmorgen SL3000 Manual de usuario

SL3000 QUICK START GUIDE

This guide is for operators who would like to get up and running quickly with a minimal amount of research

through the manual. Section 2 and sections 3.1 through 3.8 of the SL3000 instruction manual must be read.

1. Follow all safety and installation instructions as specified in Section 2, Installation Instructions.

BEFORE APPLYING POWER, VERIFY THAT THE PROPER VOLTAGE IS AVAILABLE

FOR THE INVERTER. FAILURE TO DO THIS CAN RESULT IN EQUIPMENT

DAMAGE AND PERSONAL INJURY.

2. Check all terminal connections for loose connections. Re-verify the proper motor wiring for the

voltage being applied.

3. The only connections needed on the terminal strip for keypad control are TB1-11 (Logic Common)

connected to TB1-12 (External Trip) and TB1-21 (Logic Common) connected to TB1-22 (Stop). TB1-11

and TB1-21 are both common and reference the same point.

4. Apply AC power to the input terminal (L1, L2, L3). The following will appear on the display if there

are no faults. The factory settings are for keypad operation in the forward direction.

SP0: 0 RPM

stopped

5. To change any parameters use the following procedure

a. Press the PROG key.

b. Use the MENU key to reach the desired menu.

c. Use the UP or DOWN arrow keys to get to the parameter to be changed.

d. Press the EDIT key.

e. Press the UP or DOWN arrow keys to change the parameter to a new value.

f. Press EDIT to store the new value.

g. Press the MENU key to get to a new menu.

h. Press the PROG key to exit the programming mode.

6. The standard default parameter settings should be sufficient for most applications. The parameters that

are most often changed are in the first parameter menu, MAIN MENU ( Menu 0 ) and parameter

Pr300, full load motor nameplate current. The drive performance parameters are Pr311, Slip Factor

and Pr312, Boost Factor.

7. Use the RUN FWD key to start the motor and increase the setpoint with the UP arrow keys. When

the motor starts to rotate, note the direction of rotation. If the motor is turning in the wrong direction,

STOP THE DRIVE, REMOVE AC POWER AND WAIT FOR THE BUS CHARGE

INDICATOR TO GO OUT. After the Charge indicator is extinguished, wait two minutes and

reverse any two of the motor leads (T1, T2, T3).

8. Reapply AC input power and confirm motor rotation. Use the UP and DOWN arrow keys to set speed.

9. The inverter is preset to run a “typical” NEMA B induction motor to a maximum speed of 1800 RPM

with both acceleration and deceleration times set to 3.0 seconds

10. Press the STATUS key to view the motor amps, motor frequency, buss voltage, etc..

LIM 55438 REV 0 3/95

Tabla de contenidos

Otros manuales de Servoaccionamiento de Kollmorgen

Kollmorgen

Kollmorgen S700 Series Manual de instalación y funcionamiento

Kollmorgen

Kollmorgen SERVOSTAR CD Series Manual de usuario

Kollmorgen

Kollmorgen BDS4 Series Guía del usuario

Kollmorgen

Kollmorgen AKD PDMM Manual de lista de piezas

Kollmorgen

Kollmorgen AKMH Series Manual de usuario

Kollmorgen

Kollmorgen AKD2G-S Series Manual de usuario

Kollmorgen

Kollmorgen AKD-x00306 Manual de usuario

Kollmorgen

Kollmorgen PC830 Guía de inicio rápido

Kollmorgen

Kollmorgen S700 Series Manual de instalación y funcionamiento

Kollmorgen

Kollmorgen AKD-P01206-NBEC-0000 Guía de instalación

Kollmorgen

Kollmorgen AKM Series Manual de usuario

Kollmorgen

Kollmorgen EB-8902 Manual

Kollmorgen

Kollmorgen AKD-C Series Guía de inicio rápido

Kollmorgen

Kollmorgen P70530 Manual de usuario

Kollmorgen

Kollmorgen C04 Manual de usuario

Kollmorgen

Kollmorgen S20260 Manual de usuario

Kollmorgen

Kollmorgen AKD Manual de usuario

Kollmorgen

Kollmorgen MKD-C Series Manual de funcionamiento

Kollmorgen

Kollmorgen AKD 2G Manual de usuario

Kollmorgen

Kollmorgen EB-10X Series Manual

Kollmorgen

Kollmorgen AKD EtherCAT Manual de usuario

Kollmorgen

Kollmorgen AKD series Manual de usuario

Kollmorgen

Kollmorgen SERVOSTAR 300 Manual de instalación y funcionamiento

Kollmorgen

Kollmorgen AKD-N00607 Manual de usuario

Manuales populares de Servoaccionamiento de otras marcas

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manual de usuario

Robotis

Robotis XH430-W350-T Manual de usuario

NTI AG

NTI AG LinMot C1250 Series Manual de usuario

Welcon

Welcon WE2A D048 Series Manual de usuario

Parallax

Parallax 900-00005 Manual de usuario

Festo

Festo TP 1410 Manual de usuario

Axor

Axor MAGNUM 400 Manual de usuario

Siemens

Siemens SINAMICS S120 Manual de usuario

Danfoss

Danfoss 176F6494 Manual de usuario

THORLABS

THORLABS TDC001 Manual de usuario

TECO

TECO JSDAP Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 6000 Manual de usuario

GSK

GSK DA98D Manual de usuario

Lenze

Lenze m850 Guía

Baumuller

Baumuller b maXX 3000 Manual

Baumuller

Baumuller b maXX 5000 Manual

Baumuller

Baumuller b maXX 5500 Manual

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario