Kollmorgen AKD Manual de usuario

AKD®

PROFINET RT Communication

Edition: N, November 2018

Valid for firmware version 1.18

Part Number 903-200012-00

Original Documentation

For safe and proper use, follow

these instructions.

Keep them for future reference.

Record of Document Revisions

Revision Remarks

... Table with lifecycle information of this document see "Record of Document Revisions" (➜p.

72)

K, 09/2016 Updated instructions to Submode „Program mode“ (➜p. 50).

L, 03/2017 Added PN.STW1 (➜p. 62) and PN.ZSW1 (➜p. 65).

M, 10/2017

Parameters PN.VELSCALING (➜p. 64), PN.ACCSCALING (➜p. 61) added. Manufacturer

Specific Telegram 354 (➜p. 57) added. PNU 1009, Velocity Scaling added to Supported PNU's

(➜p. 30). DRV_ACC and DRV_DEC added to signals in Telegram Configuration (➜p. 48).

N, 11/2018 AddedStandard Telegram 3 (➜p. 54).

Trademarks

lAKD is a registered trademark of Kollmorgen Corporation

lSynqNet is a registered trademark of Motion Engineering Inc.

lEnDat is a registered trademark of Dr. Johannes Heidenhain GmbH

lEtherCAT is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH

lEthernet/IP is a registered trademark of ODVA, Inc.

lsercos®is a registered trademark of sercos®international e.V.

lHIPERFACE is a registered trademark of Max Stegmann GmbH

lPROFINET is a registered trademark of PROFIBUS and PROFINET International (PI)

lSIMATIC is a registered trademark of SIEMENS AG

lWindows is a registered trademark of Microsoft Corporation

Current patents

lUS Patent 5,162,798 (used in control card R/D)

lUS Patent 5,646,496 (used in control card R/D and 1 Vp-p feedback interface)

lUS Patent 6,118,241 (used in control card simple dynamic braking)

lUS Patent 8,154,228 (Dynamic Braking For Electric Motors)

lUS Patent 8,214,063 (Auto-tune of a Control System Based on Frequency Response)

Technical changes which improve the performance of the device may be made without prior notice!

in any form (by photocopying, microfilm or any other method) or stored, processed, copied or distributed by electronic

means without the written permission of Kollmorgen.

2 Kollmorgen | kdn.kollmorgen.com | November 2018

1 Table of Contents

1 Table of Contents 3

2 General 5

2.1 About this Manual 6

2.2 Target Group 6

2.3 Symbols Used 7

2.4 Abbreviations Used 7

3 Installation and Setup 8

3.1 Important Instructions 9

3.2 PROFINET Onboard 10

3.2.1 LED Functions 10

3.2.2 Connection Technology 10

3.2.3 Network Connection Examples 10

3.3 Guide to Setup 11

3.4 Configure IP Address Parameters 12

3.4.1 Dependency Service Channel (WorkBench) and PROFINET 14

3.4.2 Reset of IP Address Parameters 14

3.5 Setup Step 7 15

3.6 Parameter Configuration with PROFIdrive over PROFINET IO 18

3.6.1 Parameter Configuration 19

3.6.2 Example for Writing the Operation Mode 20

4 PROFINET IO 21

4.1 Introduction 22

4.2 Restrictions and Requirements 22

4.2.1 Conformance Classes 22

4.2.2 Cycle Time of RT data 22

4.2.3 Connector 22

4.2.4 Network Topology 22

4.2.5 Modbus 22

5 PROFIDRIVE over PROFINET IO 23

5.1 Introduction 24

5.2 AKD as Drive Object (DO) 25

5.3 General State Machine 26

5.4 Control Word Bits (STW1) 27

5.5 Status Word Bits (ZSW1) 29

5.6 Supported PNU's 30

5.7 Signals 48

5.8 Telegram Configuration 48

5.8.1 Drive Inputs Signal 49

5.9 Velocity Mode (Application class 1) 49

5.10 Position Mode (Application class 3) 50

5.10.1 Submode „Program mode“ 50

5.10.2 Submode „Manual data input (MDI)“ 51

5.10.3 Homing 53

AKD PROFINET | Table of Contents

Kollmorgen | kdn.kollmorgen.com | November 2018 3

5.11 I/O Telegrams 54

5.11.1 Telegram 0 54

5.11.2 Standard Telegram 1 54

5.11.3 Standard Telegram 3 54

5.11.4 Standard Telegram 7 54

5.11.5 Standard Telegram 9 55

5.11.6 Manufacturer Specific Telegram 350 56

5.11.7 Manufacturer Specific Telegram 351 56

5.11.8 Manufacturer Specific Telegram 352 56

5.11.9 Manufacturer Specific Telegram 353 57

5.11.10 Manufacturer Specific Telegram 354 57

5.11.11 Standard Telegram 400 57

5.12 Units 58

5.12.1 Velocity Units 58

5.12.2 Position Units 58

5.12.3 Acc-/Deceleration Units 58

5.12.4 Current Units 58

5.13 Alarms 59

5.14 Fault 59

5.15 ASCII Configuration 59

6 PN Parameters 60

6.1 PN.ACCSCALING 61

6.2 PN.POSSCALE 62

6.3 PN.STW1 62

6.4 PN.TIMEOUTFTHRESH 63

6.5 PN.VELSCALING 64

6.6 PN.ZSW1 65

7 Sample Projects 67

7.1 Sample S7 Project 68

7.1.1 Introduction 68

7.1.2 Project Description 68

7.1.3 Getting Started 69

7.1.4 Enable the Drive and Run in Velocity Mode 70

8 Troubleshooting 71

8.1 AKD Triggers 702 Communication Fault 71

9 Record of Document Revisions 72

10 Index 73

AKD PROFINET | Table of Contents

4 Kollmorgen | kdn.kollmorgen.com | November 2018

2 General

2.1 About this Manual 6

2.2 Target Group 6

2.3 Symbols Used 7

2.4 Abbreviations Used 7

AKD PROFINET | 2 General

Kollmorgen | kdn.kollmorgen.com | November 2018 5

AKD PROFINET | 2 General

2.1 About this Manual

This manual, AKD PROFINET RT Communication, describes the installation, setup, range

of functions, and software protocol for the PROFINET AKD product series. All AKD

PROFINET drives have built-in PROFINET functionality; therefore an additional option card

is not required.

A digital version of this manual (pdf format) is available on the DVD included with your drive.

Manual updates can be downloaded from the Kollmorgen website.

Related documents for the AKD series include:

lAKD Installation Manual This manual provides instructions for installation and drive

setup.

lAKD User Guide. This manual describes how to use your drive in common applications. It

also provides tips for maximizing your system performance with the AKD. The User

Guide includes the Parameter and Command Reference Guide which provides doc-

umentation for the parameters and commands used to program the AKD.

lAccessories Manual. This manual provides documentation for accessories like cables

and regen resistors used with AKD. Regional versions of this manual exist.

Additional documentation:

lProfile-PROFIdrive (PI group, Profile-PROFIdrive_3172_v41_May06.pdf)

2.2 Target Group

This manual addresses personnel with the following qualifications:

lInstallation: only by electrically qualified personnel.

lSetup : only by qualified personnel with extensive knowledge of electrical engineering

and drive technology.

lProgramming: software developers, project-planners.

The qualified personnel must know and observe the following standards:

lISO 12100, IEC 60364 and IEC 60664

lNational accident prevention regulations

6 Kollmorgen | kdn.kollmorgen.com | November 2018

2.3 Symbols Used

Symbol Indication

DANGER Indicates a hazardous situation which, if not avoided, will res-

ult in death or serious injury.

WARNING Indicates a hazardous situation which, if not avoided, could res-

ult in death or serious injury.

CAUTION Indicates a hazardous situation which, if not avoided, could res-

ult in minor or moderate injury.

Indicates situations which, if not avoided, could result in prop-

erty damage.

This symbol indicates important notes.

Warning of a danger (general). The type of danger is specified

by the text next to the symbol.

Warning of danger from electricity and its effects.

Warning of danger from suspended loads.

Warning of danger from high temperature.

Warning of danger from automatic start.

2.4 Abbreviations Used

Abbreviation Meaning

Cat Category

DO Drive object

DU Data Unit

GSD Device description file

GSDML GSD Markup Language

HMI Human machine interface

ID Identifier

I/O Input / Output

IRT Isochronous Real-Time

LED Light emitting diode

PAP Programm Ablauf Protokoll (program sequence protocol)

PLC Programmable logic control

PNU Parameter number

RT Real-Time

STW Control word

ZSW Status word

AKD PROFINET | 2 General

Kollmorgen | kdn.kollmorgen.com | November 2018 7

AKD PROFINET | 3 Installation and Setup

3 Installation and Setup

3.1 Important Instructions 9

3.2 PROFINET Onboard 10

3.3 Guide to Setup 11

3.4 Configure IP Address Parameters 12

3.5 Setup Step 7 15

3.6 Parameter Configuration with PROFIdrive over PROFINET IO 18

8 Kollmorgen | kdn.kollmorgen.com | November 2018

3.1 Important Instructions

DANGER

High Voltage up to 900V!

There is a danger of electrical arcing with damage to contacts and serious personal injury.

lNever undo any electrical connections to the drive while it is live.

lWait at least seven minutes after disconnecting the drive from the main supply

power before touching potentially live sections of the equipment (e.g. contacts) or

undoing any connections.

WARNING

Automatic Restart!

Risk of death or serious injury for humans working in the machine. Drives with

PROFINET are remote-controlled machines. They can start to move at any time without

previous warning.

lTake appropriate measures to ensure that the operating and service personnel is

aware of this danger.

lImplement appropriate protective measures to ensure that any unintended start-up

of the machines cannot result in dangerous situations for personnel or machinery.

lSoftware limit-switches are not a substitute for the hardware limit-switches in the

machine.

Electronic equipment is basically not failure-proof. The user is responsible for ensuring

that, in the event of a failure of the drive, the drive is set to a state that is safe for both

machinery and personnel.

Install the drive as described in the Installation Manual. The wiring for the analog setpoint

input and the positioning interface, as shown in the wiring diagram in the Installation Manual,

is not required. Never break any of the electrical connections to the drive while it is live. This

action can result in destruction of the electronics.

The drive's status must be monitored by the PLC to acknowledge critical situations. Wire the

FAULT contact in series into the emergency stop circuit of the installation. The emergency

stop circuit must operate the supply contactor.

Because of the internal representation of the position-control parameters, the position con-

troller can only be operated if the final limit speed of the drive does not exceed:

rotary linear

at sinusoidal² commutation: 7500 rpm at sinusoidal² commutation: 4 m/s

at trapezoidal commutation: 12000 rpm. at trapezoidal commutation: 6.25 m/s

All the data on resolution, step size, positioning accuracy etc. refer to calculatory values.

Non-linearities in the mechanism (backlash, flexing, etc.) are not taken into account. If the

final limit speed of the motor must be altered, then all the parameters that were previously

entered for position control and motion blocks must be adapted.

AKD PROFINET | 3 Installation and Setup

Kollmorgen | kdn.kollmorgen.com | November 2018 9

AKD PROFINET | 3 Installation and Setup

3.2 PROFINET Onboard

Connection to the PROFINET Network via X11.

Connect the service interface (X11) of the drive to an Ethernet interface on the PROFINET

Master directly or via a network switch, while the supply to the equipment is switched

off.

Confirm that the link LED on the AKD (the green LED on the RJ45 connector) and on your

Master or Switch are both illuminated. If both lights are illuminated, then you have a good elec-

trical connection.

PROFINET RT and WorkBench can operate simultaneously if a switch is used.

3.2.1 LED Functions

The communication status is indicated by the built-in LEDs.

Connector LED# Name Function

X11 LED1 IN port Link ON = active, OFF= not active

LED2 RUN ON = running, OFF = not running

3.2.2 Connection Technology

You can connect to the PROFINET network using RJ-45 connectors. Use standard Cat. 5

Ethernet cables for either connection configuration.

3.2.3 Network Connection Examples

10 Kollmorgen | kdn.kollmorgen.com | November 2018

Otros manuales para AKD

Tabla de contenidos

Otros manuales de Servoaccionamiento de Kollmorgen

Kollmorgen

Kollmorgen AKM Series Manual de usuario

Kollmorgen

Kollmorgen SERVOSTAR S300 Manual de reparación

Kollmorgen

Kollmorgen AKD-CC Manual de usuario

Kollmorgen

Kollmorgen SL3000 Manual de usuario

Kollmorgen

Kollmorgen AKD Manual de usuario

Kollmorgen

Kollmorgen S700 Series Manual de instalación y funcionamiento

Kollmorgen

Kollmorgen SERVOSTAR 400 Manual de usuario

Kollmorgen

Kollmorgen SERVOSTAR 300 Manual de instalación y funcionamiento

Kollmorgen

Kollmorgen BDS4 Series Guía del usuario

Kollmorgen

Kollmorgen AKD EtherCAT Manual de usuario

Kollmorgen

Kollmorgen AKD-C Series Guía de inicio rápido

Kollmorgen

Kollmorgen AKMH Series Manual de usuario

Kollmorgen

Kollmorgen AKD 2G Manual de usuario

Kollmorgen

Kollmorgen PC830 Guía de inicio rápido

Kollmorgen

Kollmorgen AKD PDMM series Manual de usuario

Kollmorgen

Kollmorgen AKD Manual de usuario

Kollmorgen

Kollmorgen AKD PROFINET RT Communication Manual de usuario

Kollmorgen

Kollmorgen AKD series Manual de usuario

Kollmorgen

Kollmorgen AKM11B Manual de lista de piezas

Kollmorgen

Kollmorgen S700 Series Manual de instalación y funcionamiento

Kollmorgen

Kollmorgen AKD PDMM Manual de usuario

Kollmorgen

Kollmorgen AKD2G-S Series Manual de usuario

Kollmorgen

Kollmorgen MKD-C Series Manual de funcionamiento

Kollmorgen

Kollmorgen AKD Manual de lista de piezas

Manuales populares de Servoaccionamiento de otras marcas

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manual de usuario

Robotis

Robotis XH430-W350-T Manual de usuario

NTI AG

NTI AG LinMot C1250 Series Manual de usuario

Welcon

Welcon WE2A D048 Series Manual de usuario

Parallax

Parallax 900-00005 Manual de usuario

Festo

Festo TP 1410 Manual de usuario

Axor

Axor MAGNUM 400 Manual de usuario

Siemens

Siemens SINAMICS S120 Manual de usuario

Danfoss

Danfoss 176F6494 Manual de usuario

THORLABS

THORLABS TDC001 Manual de usuario

TECO

TECO JSDAP Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 6000 Manual de usuario

GSK

GSK DA98D Manual de usuario

Lenze

Lenze m850 Guía

Baumuller

Baumuller b maXX 3000 Manual

Baumuller

Baumuller b maXX 5000 Manual

Baumuller

Baumuller b maXX 5500 Manual

Danfoss

Danfoss VLT HVAC Drive FC 102 Manual de usuario