Kohler K-669 Instrucciones de montaje

Homeowners Guide

Thermostatic Mixing Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-669, K-679 K-670, K-680

1041158-5-B

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

CAUTION: Risk of scalding hazard. This device has been

calibrated at the factory to ensure a safe maximum water

temperature. Any variance in settings or water inlet conditions

from those used during factory calibration may raise the

discharge temperature above the safe limit, and may present a

scalding hazard.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

The installer is responsible for adjusting the maximum water

temperature of this valve according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the temperature adjustment

instructions in this document, in the United States please contact our

Customer Service Department at 1-800-4-KOHLER. Outside the U.S.,

please contact your distributor.

IMPORTANT NOTICE: Please ﬁll in the blanks below and on the

valve label. Retain this Homeowners Guide for future reference.

•The valve is calibrated to 104° F (40° C) at the ﬁrst stop position,

and the maximum temperature limit stop is positioned so the

outlet water temperature does not exceed 120° F (49° C).

•Factory calibrated inlet conditions are:

Hot and cold water pressure = 45 psi (3.2 kg/square cm)

Hot water supply temperature = 145° F (63° C)

Cold water supply temperature = 65° F (18° C)

•If inlet conditions differ from those used during factory

calibration, it may be necessary to re-calibrate the valve after

installation. The installer must check the mixed ﬂow

temperature after installation, and adjust the valve as needed

according to the instructions.

1041158-5-B 2 Kohler Co.

Thank You For Choosing Kohler Company

Thank you for choosing the Bold Look of Kohler. Kohler craftsmanship

offers you a rare combination of proven performance and graceful

sophistication that will satisfy you for years to come. The

dependability and beauty of your Kohler faucet will surpass your

highest expectations. We’re very proud of our products here at Kohler

and we know you will be too.

Please take a few minutes to study this Homeowners Guide. Pay

special attention to the Care and Cleaning instructions.

All information in this manual is based upon the latest product

information available at the time of publication. At Kohler, we

constantly strive to improve the quality of our products. We reserve

the right to make changes in product characteristics, packaging or

availability at any time without notice.

NOTICE TO HOMEOWNERS! This device has been preset by

_______________________ of _______________________________ to

ensure a safe maximum temperature. Any change in the setting may

raise the discharge temperature above the limit considered safe, and

lead to scalds.

Date: ______________

Kohler Co. 3 1041158-5-B

Verify the Temperature Settings

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

NOTE: The thermostatic valve cartridge is calibrated at the factory

for a shower temperature of approximately 104° F (40° C) to 105° F

(41° C) and a maximum hot temperature of 120° F (49° C).

Turn the water on.

Attach a trim handle or plaster guard (found in volume control

valve K-671 or K-681 or transfer valve K-672) onto the valve

spline adapter.

Turn the valve spline adapter fully counterclockwise so the trim

handle or plaster guard can no longer move. The valve spline

adapter is now in the full hot position.

Allow the water to run for several minutes to stabilize the water

supply temperatures.

Position a thermometer in the water stream to check the

temperature of the hot water.

If the water temperature exceeds 120° F (49° C) or is less than

desired, proceed to the ″Hot Temperature Adjustment″section.

Turn the trim handle or plaster guard clockwise until you hear a

click. Do not turn any farther. This is the shower temperature

position.

Valve Spline Adapter

Increase

temperature.

Decrease

temperature.

1041158-5-B 4 Kohler Co.

Verify the Temperature Settings (cont.)

Remove the trim handle or plaster guard from the valve spline

adapter.

Position a thermometer in the water stream to check the shower

temperature.

If the water temperature is less than 104° F (40° C) to 105° F

(41° C) or is more than desired, proceed to the ″Shower

Temperature Adjustment″section.

If both settings are correct, ﬁll out the ″Notice to Homeowners″

section of this Homeowners Guide.

Kohler Co. 5 1041158-5-B

Hot Temperature Adjustment

CAUTION: Risk of product damage. Do not overtighten the

head nut. Excessive torque may damage the head nut.

Turn both integral supply stops outward until they contact the

stop bracket.

Detach the removal clip from the head nut.

Remove the head nut from the assembly by turning the head nut

counterclockwise.

Remove the detent collar with the spring from the cartridge.

Remove the valve spline adapter.

NOTE: The spring on the detent collar may fall off. Reattach the

spring around the detent collar if this occurs.

Turn the valve stem fully counterclockwise.

NOTE: Leave the detent collar off while making adjustments.

Reinstall the head nut to the valve casting. Hand tighten the head

nut until the shoulder of the head nut contacts the lip of the

valve casting.

Turn both integral supply stops inward.

Turn on the water using the volume control valve (not shown).

Allow the water to ﬂow for several minutes to stabilize the water

temperature.

Head Nut

Removal Clip

Removal

Clip Tab

Detent Collar

with Spring

Valve Spline

Adapter

Integral

Supply

Stop

Stop Bracket

Integral Supply Stop

Valve Stem

Adapter Tab

Hot

Tab

1041158-5-B 6 Kohler Co.

Hot Temperature Adjustment (cont.)

Insert a thermometer into the water stream to verify the water

temperature.

Turn the valve stem clockwise until the maximum 120° F (49° C)

temperature is reached.

Reinstall the valve spline adapter with the adapter tab placed

ﬂush against the left side of the hot tab on the cartridge.

Reinstall the valve spline adapter in this position over the valve

stem.

Shut off the volume control.

Turn both integral supply stops outward until they contact the

stop bracket.

Open and close the volume control (not shown) to relieve

pressure that has built up in the valve.

Remove the head nut from the assembly by turning the head nut

counterclockwise.

Reinstall the detent collar. Be sure the spring is resting on top of

the detent collar.

Reinstall the head nut onto the assembly until hand-tight. Do not

overtighten.

Reattach the removal clip to the head nut. The tab on the removal

clip should be facing inward.

Turn both integral supply stops inward.

Verify the temperature. Repeat the above steps if necessary.

Proceed to the ″Shower Temperature Adjustment″section of this

guide.

Kohler Co. 7 1041158-5-B

Shower Temperature Adjustment

NOTE: To ensure the correct shower temperature, ﬁrst turn the

valve spline adapter to the full hot position then adjust the shower

temperature.

Place the trim handle (not shown) or plaster guard (not shown)

onto the valve spline adapter.

Turn the valve spline adapter fully counterclockwise so the trim

handle or plaster guard can no longer move. The valve spline

adapter is now in the full hot position.

Next, turn the trim handle or plaster guard clockwise until you

hear a click. Do not turn an farther. This is the shower

temperature position.

Remove the trim handle or plaster guard from the valve spline

adapter.

Allow the water to run for a few minutes to stabilize the

temperature.

If the temperature is less than 104° F (40° C):

Pull out the detent collar.

Turn the detent collar counterclockwise.

Verify the temperature.

If the temperature is greater than 105° F (41° C):

Pull out the detent collar.

Detent Collar

Valve Spline Adapter

Increase

temperature.

Decrease

temperature.

1041158-5-B 8 Kohler Co.

Shower Temperature Adjustment (cont.)

Turn the detent collar clockwise.

Verify the temperature.

Repeat the steps above until the desired temperature is achieved.

Troubleshooting Procedures

This troubleshooting guide is for general aid only. For warranty

service, contact your dealer or wholesale distributor.

Symptoms Probable Cause/Recommended

Action

1. Only hot or cold water from

outlet. a. Inlet supplies are reversed. See

″Reversed Inlet Supplies″section

of the Installation Guide.

b. No hot water reaching shower

control.

c. Check ﬁlter screens for blockage.

2. Fluctuating or reduced ﬂow rate. Normal function of thermostatic

control when operating conditions

are unsatisfactory.

a. Check ﬁlter screens for ﬂow

restriction.

b. Make sure that the minimum

ﬂow rate is sufficient for supply

conditions.

c. Make sure that dynamic inlet

pressures are nominally balanced

and sufficient.

d. Make sure that inlet

temperature differentials are

sufficient.

e. Service stops are not fully

threaded in. Rotate both service

stops until fully threaded.

f. Check thermostatic performance;

renew thermostatic cartridge, if

necessary.

3. No ﬂow from shower control

outlet. a. Check ﬁlter screens for blockage.

b. Hot or cold supply failure;

thermostat holding correct

shutdown function.

c. Flow control cartridge does not

work. Check and replace if

necessary.

d. Service stops are shut off. Rotate

both counterclockwise.

Kohler Co. 9 1041158-5-B

Troubleshooting Procedures (cont.)

Symptoms Probable Cause/Recommended

Action

4. Blend temperature drift. Indicates operating conditions

changed.

a. Refer to symptom 2 above.

b. Hot supply temperature

ﬂuctuation.

c. Supply pressure ﬂuctuation.

5. Hot water in cold supply or cold

water in hot supply. Indicates crossﬂow. Replace check

valve.

6. Maximum blend temperature

setting too hot or too cold. a. Indicates incorrect maximum

temperature setting; refer to the

″Adjust Temperature Settings″

section.

b. As symptom 4 above

c. As symptom 5 above.

7. Water leaking from the valve

body. Seal(s) worn or damaged.

a. Obtain service kit and replace

seal(s).

b. If leaking from around the

temperature spindle, replace the

thermostatic cartridge.

8. Flow knob or temperature knob

is stiff to operate. a. Impaired free movement of

internal components. Renew the

appropriate cartridge.

b. Supply pressures are too high.

Fit pressure reducing valve.

Lifetime Limited Warranty — USA and Canada

Kohler Co. warrants its faucets manufactured after January 1, 1997, to

be leak and drip free during normal residential use for as long as the

original consumer purchaser owns his/her home. *If the faucet should

leak or drip during normal use, Kohler will, free of charge, mail to the

purchaser the cartridge necessary to put the faucet in good working

condition.

Kohler also warrants all other aspects of the faucet, except gold ﬁnish,

to be free of defects in material and workmanship during normal

residential use for as long as the original consumer purchaser owns

his/her own home. If a defect is found in normal residential use,

Kohler Co. will, at its election, repair, provide a replacement part or

product, or make appropriate adjustment. Damage to a product caused

by accident, misuse, or abuse is not covered by this warranty. Proof of

purchase (original sales receipt) must be provided to Kohler with all

1041158-5-B 10 Kohler Co.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Producto de plomería de Kohler

Kohler

Kohler K-19029 Manual de usuario

Kohler

Kohler K-4709 Manual de usuario

Kohler

Kohler HiRise K-7337 Instrucciones de montaje

Kohler

Kohler K-13490 Instrucciones de montaje

Kohler

Kohler 23510-BL Manual de usuario

Kohler

Kohler C3-050 Manual de usuario

Kohler

Kohler K-8211 Instrucciones de montaje

Kohler

Kohler PURIST 7507T-B4 Manual de usuario

Kohler

Kohler FOLIO K-2017IN-1 Manual de usuario

Kohler

Kohler KARAT K-17555 Manual de usuario

Kohler

Kohler K-158 Manual de usuario

Kohler

Kohler K-R77748 Instrucciones de montaje

Kohler

Kohler K-10085 Instrucciones de montaje

Kohler

Kohler K-13700 Manual de usuario

Kohler

Kohler HiRise K-7344-4 Instrucciones de montaje

Kohler

Kohler K-1418-G Guía de inicio rápido

Kohler

Kohler C3-130 Manual de usuario

Kohler

Kohler K-352 Instrucciones de montaje

Kohler

Kohler K-1002-H2 Instrucciones de montaje

Kohler

Kohler COMPOSED K-20257T-B-CP Manual de usuario

Kohler

Kohler K-6340 Instrucciones de montaje

Kohler

Kohler K-7114 Manual de usuario

Kohler

Kohler KT6908 Manual de usuario

Kohler

Kohler K-8703X Instrucciones de montaje

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario

BELLOSTA

BELLOSTA romina 0308/CC Manual de usuario

Bristan

Bristan PS2 BAS C D2 Diagrama de cableado

Crosswater

Crosswater Heir 18-31 Manual de usuario