KoamTac KDC 470 Manual de usuario

1/29/2018

KDC470

User Guide

Table of Contents

1. KDC470 Product Concept ....................................................................................................................... 2

2. KDC470 Layout.......................................................................................................................................... 3

3. How to Turn the Device On or Off......................................................................................................... 3

4. How to Pair with Your Smartphone or Tablet...................................................................................... 4

5. How to Replace the Battery ....................................................................................................................6

1. KDC470 Product Concept

Sled (SmartSled®)

①.Supports virtually all smartphones

•Protect investment on Sled regardless of smartphone/tablet change.

②.Connecting with smartphones/tablets via USB/Serial and Bluetooth.

③.Can replace battery (1130mAh) easily from the side of KDC470

④.Rugged - IP65 rated, 5ft drop spec

Modular Design

①.Supports various technologies

•HF or UHF RFID Reader Module

•PCI/EMV Payment Module

•Extended Battery Pack

Custom Smart Case for simultaneous charging

①.KDC Smart Case connects both KDC470 and its smartphone/tablets.

②.One charging port, either USB port or charging cradle, charges both KDC470 and

smartphone/tablets.

2. KDC470 Layout

Below is a diagram detailing the layout and buttons on the KDC470

3. How to Turn the Device On or Off

The KDC470 is shipped with the power off.

To power on, press and hold the SCAN and DOWN buttons together for 3 seconds until the

short beep sounds.

The KDC470 will sound a long beep when it is ready to use. (it takes about 10 seconds until the

long beep)

Check the diagram above locate the SCAN and DOWN buttons.

To power off, press and hold the SCAN and DOWN buttons together for 3 seconds. You can

press the SCAN button to make sure.

4. How to Pair with Your Smartphone or Tablet

There are two different methods to pair the KDC470 to an Android host.

①.HID Normal – one-way communication with the host device. The KDC wedges data to

the Android keyboard.

②.SPP – two-way communication with an application on the host device. The KDC can send

data to the host as well as receive commands from it. When connected to Koamtac’s

KTSync application, the data can be wedged to the keyboard.

HID Normal (Basic Mode - Keyboard Wedge)

①.Scan the HID Normal & Pairing bar code on the quick manual provided with the scanner.

If done correctly, the LED light on the side of the scanner will blink orange.

②.HID Normal & Pairing (Android/Windows) – 1D

③.HID Normal & Pairing (Android/Windows) – 2D

④.Navigate to the Bluetooth settings on the host device and turn Bluetooth on.

⑤.Underneath the list of available devices, tap on the KDC470. The serial number will

appear in brackets which you can cross check with the serial number on the back of the

KDC.

⑥.The KDC will beep when connected.

⑦.Open any application with a text field and tap on the text field and scan any barcode

then it will show up on the text field.

SPP (Application Mode)

①.Scan the SPP & Pairing bar code on the quick manual provided with the scanner. If done

correctly, the LED light on the side of the scanner will blink red.

②.SPP & Pairing (Android/Windows) – 1D

③.SPP & Pairing (Android/Windows) – 2D

④.Navigate to the Bluetooth settings on the host device and turn Bluetooth on.

⑤.Underneath the list of available devices, tap on the KDC470. The serial number will

appear in brackets which you can cross check with the serial number on the back of the

KDC.

⑥.The KDC will pair to the phone, but needs to connect to an application to function

properly.

⑦.Download KTSync from the Play Store.

⑧.Open the Settings on the Android device. Navigate to Language & Input. Select Virtual

Keyboards. Then select Manage keyboards. Enable the KTSync Keyboard and allow for

any permissions.

⑨.Open KTSync and tap on the settings button on the top right of the screen.

⑩.Select Connect then select the KDC from the list of devices.

⑪.The KDC will connect. You can now scan within KTSync.

⑫.If you would like to scan outside of KTSync into another application, the KTSync software

keyboard must be selected. To switch software keyboards, tap inside of any text field.

Swipe down from the top of the device screen to bring up the notification panel. Select

the notification from the Android System to Select keyboard. Select the KTSync

keyboard. Now you can scan anywhere.

5. How to Replace the Battery

Each KDC comes with a rechargeable Lithium-Ion.

The battery may be recharged from any USB port or KDC charging cradle, and may be recharged

about 300 times before it needs to be replaced. KOAMTAC recommends replacing the battery

annually, as a declining battery will cause noticeable performance degradation in the KDC.

Replacement batteries may be purchased from a KDC reseller.

Batteries should be disposed of properly as according to the WEEE regulation.

1. Unlock the battery cover by sliding

the lock switch right.

2. Open the cover as shown in the

picture.

3. For easy removal, use a paperclip or

similar tool to pull on folded sticker.

4. Hold the sticker and remove battery.

5. <Insert the battery>

6. Before inserting battery, fold sticker

over battery lengthwise.

7. Slide the lock switch up, open the

battery cover and slide in the battery

slowly.

8. Close the battery cover and slide the

lock switch down

Otros manuales para KDC 470

Tabla de contenidos

Otros manuales de Lector de código de barras de KoamTac

KoamTac

KoamTac KDC250 Manual de usuario

KoamTac

KoamTac KDC20 Manual de usuario

KoamTac

KoamTac KDC20 Manual de usuario

KoamTac

KoamTac KDC 470 Manual de usuario

KoamTac

KoamTac KDC200 KDC250 Manual de usuario

KoamTac

KoamTac KDC475 Manual de usuario

KoamTac

KoamTac KDC380 QG Manual de usuario

KoamTac

KoamTac KDC20 Manual de usuario

KoamTac

KoamTac KDC20 Manual de usuario

KoamTac

KoamTac KDC185 Manual de usuario

KoamTac

KoamTac KDC485ER Manual de usuario

KoamTac

KoamTac KDC100 Manual del propietario

KoamTac

KoamTac KDC100 Manual de usuario

KoamTac

KoamTac KDC100 Manual de usuario

KoamTac

KoamTac KDC280 Manual de usuario

KoamTac

KoamTac KDC Series Manual de usuario

KoamTac

KoamTac KDC300 Manual de usuario

KoamTac

KoamTac SLED-mPOS Manual de usuario

KoamTac

KoamTac KDC30 Manual de usuario

KoamTac

KoamTac KBM-XP67 Manual de usuario

KoamTac

KoamTac KDC30 Manual de usuario

KoamTac

KoamTac KDC200 KDC250 Manual del propietario

KoamTac

KoamTac KDC185 QG Manual de usuario

KoamTac

KoamTac KDC20 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario