KMC Controls STE-8001 Manual de usuario

STE-8001 and STE-8201 sensors

Installation Guide

Section 1

Introduction to STE-8000 sensors

Specifications ...........................................................................................................................4

Safety considerations .............................................................................................................6

Section 2

Installing STE-8000 sensors

Planning for motion sensing .................................................................................................7

Rough-in preparation ............................................................................................................8

Installing the sensors ..............................................................................................................8

Maintenance ............................................................................................................................9

Section 3

User functions

Operating the STE-8000 .......................................................................................................11

Changing setpoints ...............................................................................................................12

Section 4

Commissioning functions

The commissioning sequence .............................................................................................14

Enter the commissioning mode ..........................................................................................14

Setting up network communications .................................................................................15

Box options ............................................................................................................................16

Setting commissioning setpoints ........................................................................................20

Setting the airflow setpoints ...............................................................................................23

Balancing airflow ..................................................................................................................27

Advanced options ................................................................................................................31

Set

Point

12O2

RevisionA

KMC Controls

Revision A2

WinControl XL Plus, NetSensor, and the KMC logo are registered trademarks of

KMC Controls, Inc.

BACstage and TotalControl are trademarks of KMC Controls, Inc.

transcribed, stored in a retrieval system, or translated into any language in any

form by any means without the written permission of KMC Controls, Inc.

Printed in U.S.A.

Disclaimer The material in this manual is for information purposes only. The contents and

the product it describes are subject to change without notice. KMC Controls, Inc.

makes no representations or warranties with respect to this manual. In no event

shall KMC Controls, Inc. be liable for any damages, direct or incidental, arising

out of or related to the use of this manual.

KMC Controls

P. O . B o x 4 9 7

19476 Industrial Drive

New Paris, IN 46553

U.S.A.

TEL: 1.574.831.5250

FAX: 1.574.831.5252

E-mail: [email protected]

Revision A 3

SECTION 1

Introduction to STE-8000 sensors

This section provides a description of the KMC Controls STE-8001

and STE-8201 wall sensors. It also introduces safety information.

Review this material before installing or operating the sensors.

Models STE-8001 and STE-8201 are wall-mounted, temperature sensor for use

with KMC BAC-8000 series VAV controllers. Key features include the following:

◆Integrated operator interface ready to use with BAC-8000 series VAV

controllers

◆Large LCD display

◆Simple three-button interface

◆Continuously displays temperature and time

◆Separate password protection for user and commissioning functions

◆Use as a service tool to set up BAC-8000 series VAV controllers

◆Optional motion sensor to detect space occupancy

Note

An STE-8000 series sensor will display time if the controller to which it is

attached has been synchronized with system time within the previous 24

hours.

Illustration 1-1 STE-8001 and STE-8201

Set

Point

12O2

Set

Point

12O2

STE-8001 STE-8201

KMC Controls

Revision A

Introduction to STE-8000 sensors

Specifications

Display Multifunctional LCD

1.88 x 1.25 in. (48 x 32 mm)

Compatibility BAC-8000 series VAV controllers

Controller Connection

Connector type Eight-wire RJ-45 modular jack

Cable type and length Standard Ethernet cable up to 75 feet (22.9 meters)

Power Supplied by connected controller

Mounting Surface mount directly to any flat surface or to a

2x 4 inch or 4 x 4 inch handy-box. Mounting on a

4x 4 inch box requires a mounting backplate.

Weight 2.8 ounces (80 grams)

Material Flame retardant plastic

Accessories

Mounting backplate HMO-1161W

Gasket HPO-116

Replacement Allen screwsHPO-0044 (package of 10)

Environmental Limits

Operating Temperature 34° to 125° F (1.1 to 51.6° C)

Shipping –40° to 140° F (–40°C to 60° C)

Humidity 0 to 95% relative humidity

non-condensing

STE-8001 and STE-8201 sensors

Revision A

Introduction to STE-8000 sensors

Specifications

Motion sensor range Model STE-8201 only

Detector type Passive infrared

Range 33 feet (10 meters). See diagrams

Dimensions

ABCDE F

3.25 in. 5.16 in. 2.58 in. 3.25 in. 0.87 in. 1.07 in.

83 mm 116 mm 66 mm 83 mm 22 mm 27 mm

55°

10 m

32.8 ft

10 m

32.8 ft

0°

10 m

32.8 ft

10 m

32.8 ft

0°

46.5°

Top view Side view

12O2

KMC Controls

Revision A

Introduction to STE-8000 sensors

Safety considerations

Models

Temperature sensor only STE-8001

Temperature and motion STE-8201

Safety

considerations KMC Controls assumes the responsibility for providing you a safe product and

safety guidelines during its use. Safety means protection to all individuals who

install, operate, and service the equipment as well as protection of the

equipment itself. To promote safety, we use hazard alert labeling in this manual.

Follow the associated guidelines to avoid hazards.

Danger

Danger represents the most severe hazard alert. Bodily harm or death will

occur if danger guidelines are not followed.

Warning

Warning represents hazards that could result in severe injury or death.

Caution

Caution indicates potential personal injury or equipment or property damage

if instructions are not followed.

Note

Notes provide additional information that is important.

Detail

Provides programing tips and shortcuts that may save time.

Revision A 7

SECTION 2

Installing STE-8000 sensors

This section provides important instructions and guidelines for

installing the STE-8000 series sensors. Carefully review this

information before installing the controllers.

Installing the sensors includes the following topics that are covered in this

section.

◆Planning for motion sensing on page 7

◆Rough-in preparation on page 8

◆Installing the sensors on page 8

◆Maintenance on page 9

Planning for

motion sensing For STE-8201 only—Mount the STE-8201 sensor on a wall that will have an

unobstructed view of the typical traffic in the coverage area. When choosing a

location, do not install the sensor in the following areas.

◆Behind curtains or other obstructions

◆In locations that will expose it to sunlight or heat sources

◆Near a heating/cooling duct.

For details on the coverage pattern, see Specifications on page 4.

The effective detection range is approximately 10 meters or 33 feet. Factors that

may reduce the range include:

◆The difference between the surface temperature of the object and the

background temperature of the room is too small.

◆Object movement in a direct line toward the sensor.

◆Very slow or very fast object movement.

◆Obstructions as shown in the illustration Typical motion sensing coverage area

on page 7.

Illustration 2-1 Typical motion sensing coverage area

KMC Controls

Revision A

Installing STE-8000 sensors

Rough-in preparation

False detections may be triggered by:

◆The temperature inside the detection range suddenly changes because of

the entry of cold or warm air from an air-conditioning or heating unit.

◆The sensor being directly exposed to sunlight, an incandescent light, or

other source of far-infrared rays.

◆Small animal movement.

Rough-in

preparation Complete rough-in wiring at each sensor location prior to sensor installation.

This includes the following.

◆Routing the connecting cable from the sensor to a controller.

◆If required, install the appropriate backplate. See Accessories on page 4 for

model numbers.

Connect the STE-8000 series sensor to a controller with a standard Ethernet cable

with RJ-45 connectors on each end. Maximum cable length is 75 feet (22.9

meters). Plenum-rated preassembled cables are recommended.

Installing the

sensors To install the sensor on a backplate, do the following:

1. Turn the Allen screws in the base of the NetSensor clockwise until they

clear the cover. Swing the sensor away from the mounting base to remove

it.

2. Route the Ethernet cable through the mounting base.

3. Fasten the mounting base directly to a 2 x 4 inch outlet box or a backplate

with the Allen screws toward the floor.

Illustration 2-2 Sensor mounting details

Connecting cable

Maximum 75 feet

or 22.9 meters

Allen

screws

Mounting

base

Illustration 2-3 Mounting screws

Turn clockwise to

remove from base.

STE-8001 and STE-8201 sensors

Revision A

Installing STE-8000 sensors

Maintenance

4. Insert the Ethernet cable coming from the base into the sensor.

5. Place the top of the sensor over the top of the mounting base and swing it

down over the Allen screw brackets. Be careful not to pinch any wiring.

6. Back the Allen screws out of the brackets until they engage the sensor cover

and hold it in place.

Maintenance Remove dust as necessary from holes in top and bottom. Clean the display with

soft, damp cloth and mild soap.

KMC Controls

Revision A

Installing STE-8000 sensors

Maintenance

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de KMC Controls

KMC Controls

KMC Controls STE-6010 Guía del usuario

KMC Controls

KMC Controls Conquest STE-90 Series Manual de usuario

KMC Controls

KMC Controls STW-6010 Manual de usuario

KMC Controls

KMC Controls STE-6014 Manual de usuario

KMC Controls

KMC Controls KMD-1183 Instrucciones de funcionamiento

KMC Controls

KMC Controls STE-6014 Guía del usuario

KMC Controls

KMC Controls STE-6010-10 Manual de usuario

KMC Controls

KMC Controls SSS-1000 Series Manual de usuario

KMC Controls

KMC Controls NetSensor KMD-1162 Instrucciones de funcionamiento

KMC Controls

KMC Controls STE-6014-10 Manual de usuario

KMC Controls

KMC Controls STW Series Manual de usuario

KMC Controls

KMC Controls STE-1421 Manual de usuario

KMC Controls

KMC Controls SSS-1000 Series Manual de usuario

KMC Controls

KMC Controls THE-1105 Manual de usuario

KMC Controls

KMC Controls NetSensor KMD-1261 Instrucciones de funcionamiento

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario