KMC Controls KMD-1183 Instrucciones de funcionamiento
Installation and
Operation Guide
KMD-1183/1185 NetSensors
Contents
Specifications ............................................................... 2
Network cable and rough-in preparation ...................... 5
Installation ................................................................... 6
PC data port ................................................................. 7
Operation .................................................................... 8
Maintainence ............................................................... 8
Programming ............................................................... 9
Important notices ....................................................... 17
Disclaimer ................................................................. 17
903-019-05ARevision A
KMC Controls
2
Specifications
Models KMD-1183
KMD-1185 (enhanced alarm functions,
see Alarm on page 14)
Display LCD, Four-character,
Seven-segment, 0.375 in. high
Blue backlight turns on momentarily
after a button is pressed
Compatibility KMD-5800 series controllers
KMD-7000 series controllers
BAC-5800 series BACnet controllers
BAC-7000 series BACnet controllers
Controller Connection
Connector type Six-wire RJ-12 modular jack
Cable type and length Up to 75 feet (22.9 meters) maximum;
conductors no smaller than 24 AWG
Power 5 volts DC supplied by connected
controller
Weight 2.8 ounces (80 grams)
Material Light almond ABS
UL Flame Class 94HB
Mounting Surface mount directly to any flat
surface or to a 2 x 4 inch or 4 x 4 inch
handy-box. Mounting on a 4 x 4 inch
box requires an HMO-1161 mounting
backplate.
NetSensor Installation and Operation
3
Accessories
Mounting backplate HMO-1161
Gasket HPO-1161
Replacement Allen screws HPO-0044 (package of 10)
Network plenum cables with connectors
25 feet (7.6 meters) KMD-5690
50 feet (15.2 meters) KMD-5691
75 feet (22.9 meters) KMD-5692
PC data port interfaces See PC data port on page 7
Temperature sensor
Type CMOS
Accuracy ±0.9° F (±0.5° C) offset from 40° to
104° F (4.4° to 40.0° C), offset is
adjusted in the controller
Resolution ±0.1° F (±0.1° C)
Operating range 36° to 120° F (2.2° to 48.8° C)
Response time 5–30 seconds
Humidity sensor
Type CMOS
Range 0–100% relative humidity
Accuracy at 25° C ±2% from 10–90% relative humidity
Response time Less than or equal to 4 seconds
Environmental limits
Operating Temperature 34° to 125° F (1.1° to 51.6° C)
Shipping –40° to 140° F (–40° to 60° C)
Humidity 0–95% relative humidity
non-condensing
KMC Controls
4
Dimensions
ABCDE
3.25 in. 5.16 in. 2.58 in. 3.25 in. 0.87 in.
83 mm 116 mm 66 mm 83 mm 22 mm
A
CD
E
B
NetSensor Installation and Operation
5
Network cable and rough-in preparation
Connecting a NetSensor to a controller requires a six-wire cable with
RJ-12 connectors on each end. KMC plenum-rated preassembled
cables are recommended. Cables made to length must meet the
following requirements:
◆Cable length must be no longer than 75 feet (22.9 meters).
◆Cable conductors must be no smaller than #24 AWG.
◆Cable insulation must meet local building codes.
◆Connectors must be appropriate for the cable in use and are
installed following the connector manufacturers instructions.
Complete rough-in wiring at each sensor location prior to sensor
installation. This includes the following:
◆Routing the network cable from the NetSensor to a controller. See
Mounting details on page 6.
◆If required, install the appropriate backplate. See Accessories on
page 3 for model numbers.
Caution
To prevent mounting screw heads from touching the circuit
board in the NetSensor, use only the mounting screws
supplied by KMC Controls. Using screws other than the
type supplied will damage the NetSensor.
Cable details
RJ-12
KMC Controls
6
.
Installation
1. Turn the Allen screws in the base of the NetSensor clockwise
until they clear the cover. Swing the sensor away from the
mounting base to remove it
2. Route the RJ-12 cable through the mounting base.
3. Fasten the mounting base directly to a 2 x 4 inch outlet box or a
backplate with the Allen screws toward the floor.
4. Insert the RJ-12 cable coming from the base into the NetSensor.
5. Place the top of the NetSensor over the top of the mounting base
and swing it down over the Allen screw brackets. Be careful not
to pinch any wiring.
6. Back the Allen screws out of the brackets until they engage the
NetSensor cover and hold it in place.
Mounting details
Network
cable
Allen
screws
Mounting
base
Turn clockwise to
remove from base.
NetSensor Installation and Operation
7
PC data port
The NetSensor is equipped with a PC data port located at the bottom
of the NetSensor housing. This port provides a temporary EIA-485
(formerly RS-485) connection to the digital network for network
setup or troubleshooting.
To use the port to connect to a computer, a means of converting the
EIA-485 signal to a USB or EIA-232 (formerly RS-232) signal will be
needed. The exact connection depends on the computer and the
operator workstation software (see also the instructions included
with those devices and software):
◆For USB (to WinControl or BACstage), use a KMD-5576 USB
Communicator (see the illustration above).
◆For EIA-232 to BACstage, use a third-party interface.
◆For EIA-232 to WinControl, use a KMD-5559 CommTalk and
KMD-5624 cable (or equivalent interface).
To use the PC data port:
1. Connect the keyed, flat end of the KMD-5624 NetSensor
interface cable (included with the KMD-5576 but not the KMD-
5559) to the port on the NetSensor.
2. Connect the RJ-12 end of the cable to the interface device that
converts the EIA-485 signal from the NetSensor into a USB or
EIA-232 signal.
3. Connect the suitable cable from the interface device to the
computer’s serial or USB port. Install any required software and
configure the port as necessary.
NetSensor PC port location and (USB) connection
KMD-5624
Cable
KMC Controls
8
Operation
The following sections describe the controls and indicators found on
the NetSensor.
Display The display contains four 0.38-inch, seven-segment LCD
digits that are visible across a normal size office. The display provides
time, temperature, and humidity readouts.
Controls These NetSensors include nine push buttons. Buttons 5
through (virtual) 8 are user programmable and can be reassigned.
(Button “8” comes from simultaneously pressing Buttons 5 and 7.)
The actual operation of the programmable buttons depends upon the
programming in the controller to which the NetSensor is connected.
See Programming on page 9. The display reverts back to the default
room temperature display about ten seconds after the last button
press.
The up and down arrow buttons adjust programmed values (where
applicable) as follows:
1. Press the button for the desired function.
2. Adjust the value up or down.
Maintainence
Remove dust as necessary from holes in top and bottom. Clean the
display with soft, damp cloth and mild soap.
NetSensor Installation and Operation
9
Programming
Program the NetSensor by associating each button with a variable or
value object in the controller to which the NetSensor is connected.
◆See NetSensor button numbers for the button numbers.
◆Table 3-1 lists typical settings for programming a NetSensor with
WinControl. Use the NetSensor dialog found under the Control
Menu to configure each button.
◆Table 3-2 lists typical settings for programming a NetSensor with
BACstage. Use the NetSensor dialog in the Device Menu to
configure each button.
NetSensor button numbers
2
13
4
5
6
7
8
(Aux.)
KMC Controls
10
Of the NetSensor’s six rectangular buttons Buttons 5, 6, 7, and
(virtual/auxiliary) 8 are labeled with standard functions, but they are
also user programmable and can be reassigned if desired. (Button “8”
comes from simultaneously pressing Buttons 5 and 7.)
Note
If Button 7 (Humidity) is reassigned, humidity will continue
being shown on the NetSensor’s display. However,
humidity readings will no longer be read by the controller.
Note
The day-of-week and system-time functions are not enabled
in all models of the controllers with which the NetSensor
may operate. Before programming a controller for one of
these features, verify the feature is available in the firmware
history for the controller.
For additional instructions on programming a NetSensor with either
WinControl or BACstage, see the Help system with either program.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios de KMC Controls
KMC Controls
KMC Controls STE-8001 Manual de usuario
KMC Controls
KMC Controls Conquest STE-90 Series Manual de usuario
KMC Controls
KMC Controls STW-6010 Manual de usuario
KMC Controls
KMC Controls NetSensor KMD-1261 Instrucciones de funcionamiento
KMC Controls
KMC Controls SSS-1000 Series Manual de usuario
KMC Controls
KMC Controls STE-6014 Guía del usuario
KMC Controls
KMC Controls SSS-1000 Series Manual de usuario
KMC Controls
KMC Controls STE-1421 Manual de usuario
KMC Controls
KMC Controls STE-6014 Manual de usuario
KMC Controls
KMC Controls STE-6014-10 Manual de usuario
