KLOCK WERKS Flare Manual de usuario
5. Use a plastic putty knife
or similar non-abrasive
tool, gently lift the nose of
the fairing off of the four
grommets in the lower
fairing.
6. Carefully remove front fairing
and set aside.
7. Use an 8mm wrench to loosen
the windshield mounting
screws and remove the stock
windshield.
3. Place a rag underneath
the mounting bolts to help
prevent them from falling
into the fairing.
8. Install your new Flare™
Windshield with the hardware
removed in step 7 and
torque fasteners to factory
specifications.
1. Remove mirror boots from
outer fairing.
2. Gently fold the mirrors
forward to expose the 6mm
fairing mount bolts.
4. Using a 10mm wrench,
remove the two mounting
bolts.
Reference your service manual for
proper windshield torque specs.
Over-tightening may crack windshield
material.
SEE PAGE 2 FOR VENT REPLACEMENT
FLARE™ WINDSHIELD FOR HONDA F6B
CUSTOMER COPY
- 10mm box end wrench
- 8mm nut driver or 8mm socket and ratchet
- plastic putty knife
TOOLS NEEDED FOR INSTALLATION:
Klock Werks Flare™ Windshield uses all of the
stock mounting hardware. Instructions lead you
through removing the stock shield and hardware,
and re-installing the Flare™.
NOTE:
KLOCK WERKS // GETKLOCKED.COM
Klock Werks cannot be held responsible for any damage resulting from improper installation performed by any consumer or their dealer.
QUESTIONS?
CALL: (605) 996.3700
info@getklocked.com
EMAIL:
1. Remove the two button head fasteners holding the vent
halves together
a. The vent shown uses a 3mm allen wrench and an
8mm socket
2. Disconnect the small plastic tab at the bottom of the vent
3. Rock the inner half up and off of the lip of the outer half and
the two pieces should release from the windshield
4. Install the vent in reverse order into your new Klock Werks
vented Flare™ windshield.
VENT REPLACEMENT
We tested many products, and found a company that would combine what we like and remove what we didn’t like to create a
complete Kleaning product line-up.
KLOCK WERKS KLEANING PRODUCTS
2312-F6B01R2 ©2016 KLOCK WERKS
MORE WAYS TO KLOCK YOURSELF OUT
KLOCK WERKS // GETKLOCKED.COM
ENGINE WERKS:
A unique water based product designed
to renew the powder-coat finish on your
motor. This product uses solvent free
and non-flammable ingredients that are
designed to deter dust and dirt from
collecting on the surface of the motor.
MATTE WERKS:
Formulated to clean and protect matte
and satin paint finishes. Matte Werks is a
proprietary mixture of polymers that will
clean away bugs and grime, and repel
dirt, dust, fingerprints and smudges, all
without adding gloss or greasiness.
SHINE WERKS:
The recommended cleaner for your Klock
Werks Flare™ Windshield, and more!
Shine Werks cleans, shines and protects
plastic, leather, acrylic, plexiglass, lexan,
chrome, fiberglass, and paint. Dries
quickly and buffs to a streak free shine!
// The recommended cleaner for your Flare™ Windshield
// Proprietary concoction designed by REAL riders
// Protects surfaces while repelling dirt
// Complete line for all finishes
// Clean, Shine, and protect - just about anything.
Otros manuales de Accesorios para motocicletas de KLOCK WERKS
Manuales populares de Accesorios para motocicletas de otras marcas
SRC
SRC B-TRK502-01-01-SL Manual de usuario
3M
3M Speedglas 9100 MP Manual de usuario
hepco & becker
hepco & becker 6307520 00 01 Manual de usuario
HOMCOM
HOMCOM AA0-077 Manual de usuario
hepco & becker
hepco & becker 6307558 00 01 Manual de usuario
Wunderkind Custom
Wunderkind Custom 106503-F15 Guía del usuario
