Klein Tools CL120KIT Manual de usuario

INSTRUCTION MANUAL

600V

400A

20M

FRANÇAIS pg. 33

ESPAÑOL pg. 17

400A AC Auto-Ranging

Digital Clamp Meter

INSTRUCTION MANUAL

400A AC Auto-Ranging

Digital Clamp Meter

400A AC Auto-Ranging

Digital Clamp Meter

• NON-CONTACT

VOLTAGE TESTING

• AUTO-RANGING

• DATA HOLD

• RANGE HOLD

• AUDIBLE

CONTINUITY

ENGLISH

CL120KIT

CAT III

600V

2 3

GENERAL SPECIFICATIONS

Klein Tools CL120 is an automatically ranging digital clamp-meter

that measures AC current via the clamp, and AC/DC voltage,

resistance and continuity via test-leads.

• Operating Altitude: 6562 ft. (2000 m)

• Relative Humidity: <95% non-condensing

• Operating Temp: 32°to 122°F (0°to 50°C)

• Storage Temp: 14°to 122°F (-10°to 50°C)

• Accuracy: Values stated at 65° to 83°F (18° to 28°C)

• Temp Coefcient: 0.1 x (Quoted Accuracy) per °C above

28°C or below 18°C, corrections are required when ambient

working temp is outside of Accuracy Temp range

• Dimensions: 8.46" x 3.54" x 1.50" (215 x 90 x 38 mm)

• Weight: 11.04 oz. (313 g) including batteries

• Calibration: Accurate for one year

• Auto Power-Off (APO): After approx. 10 minutes of inactivity

• Standards: IEC EN 61010-1, 61010-2-032, 61010-2-033.

IEC EN 61326-1, 61326-2-2.

Conforms to UL STD.61010-1,

61010-2-032,61010-2-033;

Certified to CSA STD.C22.2 NO. 61010-1,

61010-2-032,61010-2-033.

• Pollution degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 6.6 ft. (2m)

• Safety Rating: CATIII 600V, Class 2, Double insulation

• Electromagnetic Environment: IEC EN 61326-1. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

ELECTRICAL SPECIFICATIONS

Function Range Resolution Accuracy

AC Voltage

(V AC)

200.0mV 0.1mV ±(2.5% + 10 digits)

2.000V 1mV

±(2.0% + 5 digits)

20.00V 10mV

200.0V 100mV

600V 1V

DC Voltage

(V DC)

200.0mV 0.1mV ±(1.0% + 8 digits)

2.000V 1mV

±(1.0% + 3 digits)

20.00V 10mV

200.0V 100mV

600V 1V

Input Impedance: 10MΩ

Frequency Range: 45 to 400Hz

Maximum Input: 600V AC RMS or 600V DC

AC Current

(A AC)

2.000A 1mA ±(2.5% + 30 digits)

20.00A 10mA

±(2.0% + 10 digits)200.0A 100mA

400A 1A

Frequency Range: 50 to 60Hz

Resistance

200.0Ω 0.1Ω ±(1.2% + 5 digits)

2.000KΩ 1Ω

±(1.2% + 3 digits)

20.00kΩ 10Ω

200.0kΩ 100Ω

2.000MΩ 1kΩ

20.00MΩ 10kΩ ±(2.0% + 5 digits)

Maximum Input: 600V AC RMS or 600V DC

OTHER MEASUREMENT APPLICATIONS

Maximum Input: 600V DC or 600V AC RMS

• Continuity Check: Audible signal <10Ω, max current 1.5mA

• Sampling Frequency: Approx. 3 samples per second

• Overload: "OL" indicated on display

• Polarity: "-" on display indicates negative polarity

• Display: 3 ½ digit, 2000 Count LCD

4 5

ENGLISH

WARNINGS - GENERAL

To ensure safe operation and service of the meter, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Before each use verify meter operation by measuring a known voltage

or current.

• Never use the meter on a circuit with voltages that exceed the category

based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Use only with CAT III or CAT IV rated test leads.

• Ensure meter leads are fully seated, and keep fingers away from the

metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes are connected.

• Use caution when working with voltages above 25V AC RMS or 60V DC.

Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock, replace batteries

when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live circuit.

• Always adhere to local and national safety codes. Use personal protective

equipment to prevent shock and arc blast injury where hazardous live

conductors are exposed.

SYMBOLS ON METER

AC (Alternating Current) DC (Direct Current)

Resistance (in Ohms) Audible Continuity

Double Insulated Class II Ground

Warning or Caution

Risk of Electrical Shock

Suitable for uninsulated hazardous live conductors

V Voltage (Volts) A Amperage (Amps)

COM Common NCV Non-Contact Voltage Tester

Backlight SEL Select

+Positive –Negative

SYMBOLS ON LCD

AC AC (Alternating Current) DC DC (Direct Current)

Negative Reading

Data Hold

Auto Ranging MAX Maximum Value Hold

Low Battery Audible Continuity

Mega (value x 10

)

kilo (value x 10

)

milli (value x 10

-3

)

Volts

Amps Ohms

NCV

Non-Contact Voltage Tester Auto Power-Off

Hazardous Voltage Indicator

WARNINGS - NCV FUNCTION

• When NCV Function is initiated, a blinking or steady red glow and an audible

beep indicate voltage present. If no indication, voltage could still be present.

• Before and after each use of the NCVT, verify operation by testing a known

working circuit that is within the rating of this unit.

• Never assume neutral or ground wires are de-energized. Neutrals in multi-wire

branch circuits may be energized when disconnected and must be retested

before handling.

• The NCV tester WILL NOT detect voltage if:

• The wire is shielded.

• The

operator is not grounded or is otherwise isolated from an effective earth ground.

• The voltage is DC.

• The NCV tester MAY NOT detect voltage if:

• The user is not holding the tester.

• The user is insulated from the tester with a glove or other materials.

• The wire is partially buried or in a grounded metal conduit.

• The tester is at a distance from the voltage source.

• The field created by the voltage source is blocked, dampened, or otherwise

interfered with.

• The frequency of the voltage is not a perfect sine wave between 50 and 500Hz.

• The tester is outside of operation conditions (listed in Specifications section).

• Operation may be affected by differences in socket design and insulation

thickness and type; tester may not be compatible with some types of standard

or tamper resistant (TR) electrical outlets.

• Do not apply to uninsulated hazardous live conductors.

• Detection above 50V is specified under “normal” conditions as specified below.

The tester may detect at a different threshold at different conditions, or may not

detect at all unless:

• The

tip of the tester is within 0.25" of an AC voltage source radiating unimpeded.

• The user is holding the body of the tester with his or her bare hand.

• The user is standing on or connected to earth ground.

• The air humidity is nominal (50% relative humidity).

• The tester is held still.

6 7

ENGLISH

FEATURE DETAILS

NOTE: There are no user-serviceable parts inside meter.

1. 2000 count LCD display 8. "MAX" (Maximum) button

2. Function selector switch 9. Data Hold button

3. Clamp 10.

Clamp trigger

4. "COM" jack 11. Arrow markings

5. "VΩ" jack 12. NCV Button

6. Backlight button 13. NCV Light

7. "RANGE" button 14. NCV Sensing Antenna

FUNCTION BUTTONS

ON/OFF

To power ON the meter, rotate the Function Selector switch

from

the OFF setting to any measurement setting. To power OFF the meter,

rotate the Function Selector switch

to the OFF setting. The Auto-

Power Off icon will be visible in the display. By default, the meter

will automatically power OFF after 10 minutes of inactivity. If the meter

automatically powers-OFF while in a measurement setting, press any

button to power the meter ON, or rotate Function Selector

switch

to OFF, then power ON the meter. To deactivate Auto-Power OFF

functionality press and hold the "NCV" button

before powering ON

from the OFF setting. When Auto-Power OFF is deactivated, the Auto-

Power Off icon will not be visible in the display.

BACKLIGHT

Press Backlight button symbol

to turn ON or OFF the backlight.

The backlight does not automatically power OFF.

RANGE

The meter defaults to auto-ranging mode . This mode

automatically determines the most appropriate measurement range

for the testing that is being conducted.

To manually force the meter to

measure in a different range, use the

"RANGE"

button

1. Press the "RANGE" button

to manually select measurement

range ( is deactivated on the LCD). Repeatedly press the

"RANGE" button

to cycle through the available ranges,

stopping once the desired range is reached.

2. To return to auto-ranging mode, press and hold the "RANGE"

button

for more than two seconds ( is reactivated).

MAX

When the "MAX" button

is pressed, the meter keeps track of the

Maximum value as the meter continues to take samples.

1. When measuring, press "MAX" button

to display the

maximum value. If a new maximum occurs, the display

updates with that new value.

2. Press "MAX" button

again to return to normal measuring mode.

DATA HOLD

Press the Data Hold button

to hold the current measurement on

the display. Press again to return to live measuring mode.

NCV

Press and hold the "NCV" button

to enter Non-contact Voltage

Testing (NCV) mode to test for presence of AC voltage.

The NCV

icon and "EF" will be present on the display. Approach the conductor

under test leading with the sensing antenna

. In the presence of

AC voltage, the red NCV light

will illuminate and audible signals

(beeps) will sound.

As the NCV sensing antenna

approaches

the voltage source, the frequency of the audible sound will increase.

Release the "NCV" button to exit NCV testing mode.

NOTE: Only voltages of 40V AC or greater will be detected.

8 9

ENGLISH

OPERATING INSTRUCTIONS

AC CURRENT (LESS THAN 400A)

AC Current is measured by pressing the clamp trigger

to open

the clamp and placing it around a current-carrying wire. When

measuring, care should be taken to ensure that the clamp is

completely closed with trigger

fully released, and that the wire

passes perpendicularly through the center of the clamp in line with

the arrow markings

To measure current:

1. Rotate the Function Selector switch

to the 200/400 A setting.

2. Place clamp around wire. The current measurement will be shown

in the display.

NOTE: If the measurement is less than 20A, rotate the Function

Selector switch

to the 2/20 A setting for improved resolution.

Disconnect test leads when measuring with the clamp.

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

Do not test if leads are improperly seated. Results could cause

intermittent display readings. To ensure proper connection, firmly

press leads into the input jack completely.

TESTING IN CAT III MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CATIII / CATIV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

INCORRECT

CORRECT

0.7" (18 mm)

5/32"

(4 mm)

HOT WIRE

GROUND WIRE

LIVE

CABLE

NEUTRAL WIRE

10 11

ENGLISH

OPERATING INSTRUCTIONS

AC/DC VOLTAGE (LESS THAN 600V)

1. Insert RED test lead into VΩ jack

, and BLACK test lead into

COM jack

, and rotate function selector switch

to the

DC Voltage or AC Voltage setting. Note "DC" or "AC"

on the display.

2. Apply test leads to the circuit to be tested to measure voltage.

The meter will auto-range to display the measurement in the

most appropriate range.

NOTE: If "–" appears on the LCD, the test leads are being applied to

the circuit in reverse. Swap the position of the leads to correct this.

NOTE: When in a voltage setting and the test leads are open,

readings of order mV may appear on the display. This is noise and

is normal. By touching the test leads together to close the circuit

the meter will measure zero volts.

NOTE: To access mV range for V AC the "RANGE" button

must be used.

NOTE: When voltages in excess of 25V AC or 60V DC are

measured, the Hazardous Voltage Indicator will appear on the

display.

Red leadBlack lead

Manual Mode Sequence

First

Press Second

Press Third

Press Fourth

Press Fifth

Press

AC Range 0-600V 0-200V 0-20V 0-2V 0-200mV

DC Range 0-20V 0-2V 0-200mV 0-600V 0-200V

OPERATING INSTRUCTIONS

RESISTANCE MEASUREMENTS

1. Insert RED test lead into VΩ jack

, and BLACK test lead into COM

jack

, and rotate function selector switch

to the Resistance

setting. The resistance symbol will appear on the display.

2. Remove power from circuit.

3. Measure resistance by connecting test leads to circuit. The

meter will auto-range to display the measurement in the most

appropriate range.

NOTE: When in a Resistance setting and the test leads are open

(not connected across a resistor), or when a failed resistor is under

test, the display will indicate O.L. This is normal.

DO NOT attempt to measure resistance on a live circuit.

CONTINUITY

1. Insert RED test lead into VΩ jack

and BLACK test lead into COM

jack

, and rotate function selector switch

to the Continuity

setting.

2. Remove power from circuit.

3. Test for continuity by connecting conductor or circuit with test

leads. If resistance is measured less than 10Ω, an audible signal

will sound and display will show a resistance value indicating

continuity. If circuit is open, display will show "OL".

DO NOT attempt to measure continuity on a live circuit.

Red leadBlack lead

12 13

MAINTENANCE

BATTERY REPLACEMENT

When indicator is displayed on LCD, batteries must be replaced.

1. Loosen captive screw and remove battery cover.

2. Replace 3 x AAA batteries (note proper polarity).

3. Replace battery cover and fasten screw securely.

To avoid risk of electric

shock, disconnect leads from

any voltage source before

removing battery door.

To avoid risk of electric

shock, do not operate meter

while battery door is removed.

To avoid risk of electric

shock, disconnect leads from

any voltage source before

To avoid risk of electric

shock, do not operate meter

while battery door is removed.

Replace battery cover and fasten screw securely.

CLEANING

Be sure meter is turned off and wipe with a clean, dry lint-free

cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when meter is not in use for a prolonged

period of time. Do not expose to high temperatures or humidity.

After a period of storage in extreme conditions exceeding the limits

mentioned in the General Specifications section, allow the meter to

return to normal operating conditions before using.

WARRANTY

www.kleintools.com/warranty

DISPOSAL /RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov/recycle for additional

information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street Lincolnshire, IL 60069 1-800-553-4676

[email protected] www.kleintools.com

GENERAL SPECIFICATIONS

Relative Humidity: < 85% non-condensing

Operating Temperature: 32° to 140°F (0° to 40°C)

Storage Temperature: 14° to 122°F (-10°C to 50°C)

Weight: 1.3 oz. (37 g)

Nominal Power: 0.3W

Certication:

Conforms To UL Std 1436

Certified To CSA Std C22.2 # 160

Drop Protection: 6.6 ft. (2 m)

Nominal Voltage: 110/125V AC at 50/60Hz in 3-wire outlet

WARNINGS

Read, understand, and follow all warnings and instructions before

operating testers. Failure to follow instructions could result in

death or serious injury.

• Before each use, verify tester operation by testing on a known live

and correctly wired receptacle.

• Do not use if the tester appears damaged in any way.

• The tester is intended for indoor use only.

• Other equipment or devices attached to the circuit being tested

could interfere with the tester; clear the circuit before testing.

• This tester only detects common wiring problems. Always consult

a qualified electrician to resolve wiring problems.

ENGLISH

RT210

Hot (Black)

Ground (Green)

Neutral (White)

INDICATOR FAULT EXPLANATION

Open Ground Ground contact is not connected

Open Neutral Neutral contact is not connected

Open Hot Hot contact is not connected

Hot/Ground Reversed Hot and ground connections are reversed

Hot/Neutral Reversed Hot and neutral connections are reversed

Correct Receptacle is wired correctly

Indicator Illuminated

YELLOWRED

FIG. 1

Indicator Not Illuminated

14 15

ENGLISH

WIRING CONFIGURATION TESTING

Conditions indicated: wiring correct, open ground, reverse polarity,

open hot, open neutral and hot/ground reversed.

Conditions NOT indicated: quality of ground, multiple hot wires,

combinations of defects, reversal of grounded and grounding

conductors.

All appliances or equipment on the circuit being tested should be

unplugged to help reduce the possibility of erroneous readings.

STANDARD RECEPTACLES

1. Verify tester operation by testing on a known live and correctly

wired receptacle.

2. Plug tester into receptacle.

3. Compare the illuminated lights on the tester to the key code

printed on the tester.

4. If the tester indicates that the receptacle is not wired correctly,

consult a qualified electrician.

GFCI RECEPTACLES

1. Check the GFCI receptacle user manual for information on how the

specific receptacle operates prior to using this tester.

2. Insert the tester into the receptacle under test to check for

correct wiring (See FIG. 1). Lights on the tester should

illuminate.

3. Press the "TEST" button on the GFCI receptacle.

Did the GFCI trip and the lights on the tester go dark?

YES:

Reset the GFCI by pressing the reset button. Proceed to

step 4.

NO:

The GFCI is not operating properly or the receptacle is

miswired. Consult a qualified electrician.

4. Press and hold the test button on the tester for 7 seconds.

Did the

GFCI trip and the lights on the tester go dark?

YES:

Reset the GFCI by pressing the reset button. The GFCI

appears to be operating properly.

NO:

The GFCI is not operating properly or the receptacle is

miswired. Consult a qualified electrician.

CLEANING

Wipe with a clean, dry lint-free cloth.

Do not use abrasive

cleaners or solvents.

DISPOSAL /RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov/recycle for additional

information.

DESCRIPTION

The Line Splitter 10x assists in measuring the current draw of a

connected load such as an electrical device or appliance up to 15A

without splitting the device or appliances power cord. It has been

designed for use with Klein Tools clamp meters, but will also function

with many other manufacturers’ clamp meters.

GENERAL SPECIFICATIONS

Relative Humidity: < 85% non-condensing

Operating Temperature: 32° to 122°F (0°C to 50°C)

Storage Temperature: -4° to 140°F (-20°C to 60°C)

Dimensions: 4.67" x 2.28" x 1.22" (119 x 58 x 31 mm)

Nominal Voltage: 110/125V AC at 50/60Hz in 3-wire outlet

Weight: 3.2 oz. (90.7 g)

Drop Protection: 3.3 ft. (1 m)

Maximum Load Current: 15A

Measurement Correction: Clamp Meter will display 10x actual

current, eg. Actual current of 1.5A will be displayed as 15A on

clamp meter when using Line Splitter 10x.

WARNINGS

• Read, understand, and follow all warnings and instructions before

operating this device. Failure to follow instructions could result in death or

serious injury.

• Do NOT use with current loads greater than 15A (which would be displayed

as greater than 150A on a clamp meter using the Line Splitter 10x).

• Risk of electric shock and burn. Contact with live circuits could result in

death or serious injury.

• Do not use if Line Splitter 10x appears damaged in any way, if in doubt,

replace Line Splitter 10x.

• Always wear approved eye protection.

• Do NOT use Line Splitter 10x if wet.

• Intended for indoor use only.

• Always consult a qualified electrician to resolve wiring problems.

69409

FIG. 2

Receptacle

Clamp Meter

Line Splitter 10×

Load

MANUAL DE INSTRUCCIONES

Multímetro digital

de ganchode rango

automáticode

400A CA

MANUAL DE INSTRUCCIONES

Multímetro digital

de ganchode rango

automáticode

Multímetro digital

de ganchode rango

automáticode

• PRUEBA DE VOLTAJE

SIN CONTACTO

• RANGO AUTOMÁTICO

• RETENCIÓN

DE DATOS

• RETENCIÓN

DE RANGO

• INDICADOR

DE CONTINUIDAD

AUDIBLE

600 V

400 A

20 M

ESPAÑOL

USING THE LINE SPLITTER (FIG. 2)

1. Plug Line Splitter 10x into receptacle.

2. Plug the load (appliance or device) into the line splitter.

3. Measure current by clamping the clamp meter around the Line

Splitter 10x.

4. The current measured by the clamp meter is 10x the actual current

present in the circuit.

ENGLISH

CLEANING

Wipe with a clean, dry lint-free cloth.

Do not use abrasive

cleaners or solvents.

DISPOSAL /RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov/recycle for additional

information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-800-553-4676

[email protected]

www.kleintools.com

CL120KIT

CAT III

600V

18 19

ESPECIFICACIONES GENERALES

Klein Tools CL120 es un multímetro digital de gancho de rango automático

que mide corriente CA con las pinzas y voltaje CA/CD, resistencia y

continuidad con cables de prueba.

• Altitud de funcionamiento: 6562' (2000m)

• Humedad relativa: <95%, sin condensación

• Temperatura de funcionamiento: 32°a 122°F (0°a 50°C)

• Temperatura de almacenamiento: 14°a 122°F (-10°a 50°C)

• Precisión: valores establecidos según una temperatura ambiente de

65 a 83°F (18 a 28°C)

• Coeciente de temperatura: 0,1 × (precisión indicada) por cada

°C por encima de los 28°C o por debajo de los 18°C, esnecesario

realizar correcciones si la temperatura del ambiente de trabajo se

encuentra fuera del rango de precisiónde temperatura

• Dimensiones: 8,46" × 3,54" × 1,50" (215 × 90 × 38mm)

• Peso: 11,04 oz (313g) incluidas las baterías

• Calibración: precisa durante un año

• Función de apagado automático (APO): después de

aproximadamente 10minutos de inactividad

• Normas: IECEN61010-1, 61010-2-032, 61010-2-033.

IECEN61326-1, 61326-2-2.

Cumple con las normas UL STD.61010-1,

61010-2-032, 61010-2-033;

Certificado según las normas CSA STD.C22.2 n.º 61010-1,

61010-2-032, 61010-2-033.

• Grado de contaminación: 2

• Precisión: ± (% de lectura + cantidad de dígitos menos significativos)

• Protección ante caídas: 6,6' (2m)

• Clasicación de seguridad: CATIII 600V, clase 2, doble aislamiento

• Entorno electromagnético: IEC EN 61326-1. Este equipo cumple con

los requisitos para su uso en entornos electromagnéticos básicos

y controlados, como propiedades residenciales, establecimientos

comerciales e instalaciones deindustria ligera.

Especificaciones sujetas a cambios.

ESPAÑOL

ESPECIFICACIONES ELÉCTRICAS

Función Rango Resolución Precisión

Voltaje CA

(V CA)

200,0mV 0,1mV ± (2,5% + 10dígitos)

2,000V 1mV

± (2,0% + 5dígitos)

20,00V 10mV

200,0V 100mV

600V 1V

Voltaje CD

(V CD)

200,0mV 0,1mV ± (1,0% + 8dígitos)

2,000V 1mV

± (1,0% + 3dígitos)

20,00V 10mV

200,0V 100mV

600V 1V

Impedancia de entrada: 10MΩ

Rango de frecuencia: 45 a 400Hz

Entrada máxima: 600V CA RMS o 600V CD

Corriente CA

(A CA)

2,000A 1mA ± (2,5% + 30dígitos)

20,00A 10mA

± (2,0% + 10dígitos)200,0A 100mA

400A 1A

Rango de frecuencia: 50 a 60Hz

Resistencia

200,0Ω 0,1Ω ± (1,2% + 5dígitos)

2,000kΩ 1Ω

± (1,2% + 3dígitos)

20,00kΩ 10Ω

200,0kΩ 100Ω

2,000MΩ 1kΩ

20,00MΩ 10kΩ ± (2,0% + 5dígitos)

Entrada máxima: 600V CA RMS o 600V CD

OTRAS APLICACIONES DE MEDICIÓN

Entrada máxima: 600V CD o 600V CA RMS

• Vericación de continuidad: señal audible < 10Ω, 1,5mA de

corrientemáxima

• Frecuencia de muestreo: aprox. 3 muestras por segundo

• Sobrecarga: se indica “OL” en la pantalla

• Polaridad: “-” en pantalla indica polaridad negativa

• Pantalla: LCD de 3 ½ dígitos con recuento de 2000

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de Klein Tools

Klein Tools

Klein Tools LAN Scout Jr. 2 Manual de usuario

Klein Tools

Klein Tools CL445 Manual de usuario

Klein Tools

Klein Tools CL310 Manual de usuario

Klein Tools

Klein Tools CL800 Manual de usuario

Klein Tools

Klein Tools MM6000 Manual de usuario

Klein Tools

Klein Tools CL360 Manual de usuario

Klein Tools

Klein Tools VDV500-705 Manual de usuario

Klein Tools

Klein Tools CL450 Manual de usuario

Klein Tools

Klein Tools CL600 Manual de usuario

Klein Tools

Klein Tools CL440 Manual de usuario

Klein Tools

Klein Tools VDV500-051 Manual de usuario

Klein Tools

Klein Tools CL110 Manual de usuario

Klein Tools

Klein Tools CL330 Manual de usuario

Klein Tools

Klein Tools MM1300 Manual de usuario

Klein Tools

Klein Tools CL380 Manual de usuario

Klein Tools

Klein Tools ET180 Manual de usuario

Klein Tools

Klein Tools Toner-Pro VDV500-123 Manual de usuario

Klein Tools

Klein Tools ET910 Manual de usuario

Klein Tools

Klein Tools CL200 Manual de usuario

Klein Tools

Klein Tools VDV501-098 Manual de usuario

Klein Tools

Klein Tools IR3000 Manual de usuario

Klein Tools

Klein Tools NCVT-1XTKIT Manual de usuario

Klein Tools

Klein Tools VDV500-123 Probe-Pro Manual de usuario

Klein Tools

Klein Tools CL210 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario