Klaxon Flashguard Minn-X Manual de usuario
Installation Instructions
Thank you for buying Flashguard the generic term for sounder/strobe units.
BATTERY
(Not Minn-X)
PIEZO
SOUNDER
A
H
J
B
A
PCB
1
2
3
4
5
6
D
C
E
F
GI
Warning
Protect
Hearing
Off On
15 3
Battery
Time
WARNING - HIGH VOLTAGE
SAB SCB
Micro
Switch
1-STRODE
2- TRIG -
3- SUPPLY +
4- SUPPLY -
5- TAMPER R
6- TAMPER S
LED
SERIES
TAMPER
KEY
A- Mounting Hole
B- Cable Entry Hole
C- Battery Jumper (not Minn-x)
D- Cut Off Timer Jumper (not Minn-x)
E- SAB/SCB Jumper (not Minn-x)
F- Connection Terminal Block
G- Series Tamper Jumper
H- Tamper Switch
I- Power LED
J- Cable Grips
K- Screw cover / lens
K
A
Minn-XE Manuel issue 4 no 2 25/3/03 7:59 am Page 4
www.acornfiresecurity.com
www.acornfiresecurity.com
Mounting Instructions
● Using the backplate of the unit (or the template on the rear of the carton), mark the position of
the screw holes (A) and cable entry hole (B) on the wall at the selected mounting position.
●Drill and plug the wall as marked.
● Using a long masonry bit, drill a hole through the wall to allow the cable to pass through.
● To remove the front cover on the Minn-XW, gently remove the transparent cover using a screwdriver as shown
in fig 1 and remove the screw.
●Mount the unit on the wall with screws provided, not forgetting to pass the cable through the entry
hole on the backplate.
● Make the connections to the terminal block (refer to sections 3-4).
● Configure the jumpers as described in section 2 (not Minn-X).
● Replace the lid and tighten screw. (On Minn-XW, ensure the transparent screw cover is replaced, see fig 2)
● Alternatively, when used indoors the unit can also be connected to surface wiring or trunking using the
knock out cable entry on the top surface of the cover.
● The back plate also has mounting holes for attachment directly to a BS 4662 plaster depth back box.
Jumper Settings (Minn-X)
Battery (C)
Once installed, this jumper must be moved to the ON
position to connect the battery.
This will activate the automatic 5 second sound test.
The LED will not illuminate until the hold-off voltage is applied.
Cut Off Timer (D) - for the sounder
Can be set to either 15 or 3 minutes by putting
the jumper on the relevant pair of pins.
Note: Removing the jumper selects 3 minutes cut off time.
SAB / SCB Operation (E)
Move jumper to SCB position to minimise the current drawn from
control panel. A reduction in sound level occurs in SCB mode.
Series Tamper (G)
This jumper must be removed when the tamper loops of two
sounders are connected in series to the same control panel
1
2
Off On
O
SAB SCB
O
O
Time
15/3
Series
Tamper
O
fig 1 fig 2
Minn-XE Manuel issue 4 no 2 25/3/03 7:59 am Page 5
www.acornfiresecurity.com
www.acornfiresecurity.com
Terminal Connections (F)
STROBE Applying a negative voltage triggers the strobe.
TRIG - Applying a negative voltage triggers the sounder.
SUPPLY + The permanent 12V DC supply from the panel is connected to these terminals.
If the hold-off supply is removed from these terminals, the unit will self activate on
SUPPLY - battery backup (Note: The LED will stop flashing on battery backup.)
TAMPER R Sounder tamper loop negative return.
TAMPER S This terminal is only used when connecting two units in series.
(Note: remove series tamper jumper when using tamper S input)
Typical Wiring Configurations
5 wire connection (with NiMH battery)
5 wire connections for 2 units in series (with NiMH battery)
3
4
1
2
3
4
5
6
Panel Sounder
0V Strobe
0V Sounder Trigger
+12V Hold off supply
0V Hold off supply
Tamper return
STROBE
TRIG -
SUPPLY +
SUPPLY -
TAMPER R
TAMPER S
1
2
3
4
5
6
0V Strobe
0V Sounder Trigger
+12V Hold off supply
0V Hold off supply
Tamper return
Remove Series Tamper jumper
(G) on PCB Leave Series Tamper jumper
(G) on PCB
STROBE
TRIG -
SUPPLY +
SUPPLY -
TAMPER R
TAMPER S
1
2
3
4
5
6
1
2
3
4
5
6
Panel Sounder Sounder
}
Minn-XE Manuel issue 4 no 2 25/3/03 7:59 am Page 6
www.acornfiresecurity.com
www.acornfiresecurity.com
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Sistema de seguridad de Klaxon
Klaxon
Klaxon Nexus 120 AC Manual de usuario
Klaxon
Klaxon Super M Manual de usuario
Klaxon
Klaxon Nexus 120 DC Manual de usuario
Klaxon
Klaxon Nexus AC Sounder & Sounder-Beacon Manual de usuario
Klaxon
Klaxon TCC-00 Series Manual
Klaxon
Klaxon SO4 Series Manual de usuario
Klaxon
Klaxon GP10 Manual de instrucciones
Klaxon
Klaxon Nexus Pulse 110 Manual de usuario
Klaxon
Klaxon Nexus 110 AC Manual de usuario
Klaxon
Klaxon SLD-0001 Manual de usuario
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario