Kichler Lighting Starkk Manual de usuario

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

42"/52" Starkk™LED

2 | KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES..................................................................4

TOOLS REQUIRED............................................................5

PACKAGE CONTENTS ................................................... 6

MOUNTING OPTIONS.................................................... 6

HANGING THE FAN..........................................................7

INSTALLATION OF SAFETY SUPPORT................... 9

ELECTRICAL CONNECTIONS .................................. 10

FINISHING THE INSTALLATION................................ 11

ATTACHING THE FAN BLADES.................................12

INSTALLING THE Light PLATE ..................................12

INSTALLING THE LIGHT KIT.......................................13

INSTALLING THE GLASS SHADE.............................14

OPERATING INSTRUCTIONS.....................................15

TROUBLESHOOTING....................................................16

FCC INFORMATION ...................................................... 18

42"/52" Starkk™ LED | 3

4 | KICHLER.COM

1. CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker

panel or main fusebox before starting and during

the installation.

2. WARNING: This fixture is intended for installation

in accordance with the National Electrical Code

(NEC) and all local code specifications. If you are

not familiar with code requirements, installation by

a certified electrician is recommended.

3. WARNING: To reduce the risk of fire or electric

shock, use only the control provided with the fan.

4. WARNING: To reduce the risk of fire, electric

shock, or Personal Injury, mount directly to a

structural framing member or to an outlet box

marked “Acceptable for Fan Support of 15.9kg

(35 lbs) or less”. For outlet box mounting, use

mounting screws provided with the outlet box.

5. To operate the reverse function on this fan, slide

the reverse switch to the opposite position. Do

not operate reversing switch while fan blades

are in motion. Fan must be turned o and blades

stopped before reversing blade direction.

6. Avoid placing objects in the path of the blades.

7. To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

8. Make sure the installation site you choose allows a

minimum clearance of 7 feet from the blades to the floor

and at least 30 inches from the ends of the blades to any

obstruction.

9. Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened cloth

will be suitable for most cleaning.

10. After making the electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be spread

apart with the ground wire and white (common) wire to

one side with the black (load) wire to the other side of

the outlet box.

11. Electrical diagrams are for reference only. Light kits

that are not packed with the fan must be ETL Listed

and marked suitable for use with the model fan you are

installing. Switches must be ETL General Use Switches.

Refer to the Instructions packaged with the light kits

and switches for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES)

DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

SAFETY RULES

TOOLS AND MATERIALS REQUIRED

Package contents

• Phillips Screwdriver

• Blade Screwdriver

• 11 mm Wrench

• Step Ladder

• Wire Cutters

Unpack your fan and check the contents. You should have the following items:

A. Mounting Bracket

B. Ball / Downrod Assembly (1)

C. Canopy

D. Canopy Trim Ring

E. Coupling Cover

F. Motor Body

G. Blade

H. Light Plate

I. LED Light Kit

J. Glass

K. Fob (2)

L. Mounting Hardware Package

M. Package Contents:

1.) Mounting Connectors (3)

2.) Blade Attachment Hardware:

Blade Screw (15)

Fiber Washer (15)

3.) Safety Cable Hardware:

Wood Screw (1)

Flat Washer (1)

Spring Washer (1)

42"/52" Starkk™ LED | 5

6 | KICHLER.COM

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect

the power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box

and its support must be able to fully support the full weight of

the fan (up to 50 lbs). Do not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for optimal operation.

NOTE: You must use 12" or longer downrod for 30° slope

(max angle 30°). (Fig. 3)

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist

Hanger” for the support of the outlet box. Make sure the joist

hanger you purchase has been designed for use with ceiling

fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Fig. 3

Fig. 4

Outlet box

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 30° ANGLE

Fig. 5

Fig. 6

Fig. 7

Outlet Box

Mounting

Bracket

Flat Washer

Screw

Mounting

Bracket

Shoulder

Downrod

Set Screw

Hanger Ball

Cross Pin

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is necessary for

your safety and also the proper programming of the control system.

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely

fastened to at least two points to a structural ceiling member (a loose box will cause the

fan to wobble). Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. Install mounting bracket to outlet box in ceiling

using the screws and washers included with the outlet box. (Fig. 5)

Step 2. Remove one of the two shoulder screws in the mounting bracket and save it for

later use. Loosen the second shoulder screw without fully removing it. (Fig. 6)

Step 3. Remove the hanger ball from downrod assembly by loosening set screws,

removing the cross pin, and twisting ball o the rod. ( Fig. 7)

42"/52" Starkk™ LED | 7

8 | KICHLER.COM

HANGING THE FAN (continued)

Step 4. Loosen the two set screws and remove the clip and cross pin from the top

coupling of the motor body.Carefully feed the fan wires up through the downrod.

Thread the downrod onto the motor coupling until the cross pin holes are aligned.

Next, replace the cross pin and clip, and tighten both set screws. (Fig.8)

Step 5. Slip the coupling cover, canopy trim ring and canopy onto the downrod.

Carefully reinstall the hanger ball onto the downrod. Make sure the cross pin is

in the correct position and the set screws are tight and the wires are not twisted.

(Fig.9)

Step 6. Now lift the motor body into position and place the hanger ball into the

hanger bracket. Rotate until the “Check Tab” has dropped into the “Registration

Slot” and seats firmly. (Fig.10) The entire motor body should not rotate if this is

done correctly.

WARNING: Failure to properly seat the “Check Tab” can damage the ceiling fan

during operation.

Cross Pin

Clip

Set Screw

Cross Pin

Set Screw Motor Body

Fig. 8

Fig. 9

Fig. 10

Canopy

Hanger Ball

Canopy Trim Ring

Coupling Cover

Motor Body

Mounting

Bracket

Hanger

Ball Registration Slot

Check Tab

Flat Washer

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 11)

Step 2. Insert the safety cable through the mounting bracket and one of the holes in

the outlet box into the ceiling. Adjust the length of the safety cable to reach the screw

and washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the safety

cable over the wood screw and under the washer. Tighten the wood screw securely.

(Fig. 12)

NOTE: Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable Bolt

Wood Screw

Fig. 12

Fig. 11

42"/52" Starkk™ LED | 9

10 | KICHLER.COM

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the power at

the main circuit panel before wiring.

Follow the steps below to connect the fan to your household wiring. Use the wire

connectors supplied with your fan. Secure the connector with electrical tape. Make sure

there are no loose wire stands or connections.

WARNING: If your house wires are dierent colors than referenced in this manual, stop

immediately. A professional electrician is recommended to determine proper wiring.

Step 1. Connect the fan supply (black) wire and light supply (blue) wire to the black

household supply wire as shown in Figure 13.

Step 2. Connect the neutral fan (white) wire to the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to the household ground wire.

Step 4. After connecting the wires, spread them apart so that the green and white wires

are on one side of the outlet box and the black wires is on the other side.

NOTE: Carefully tuck the wire connections up into the outlet box.

Vac 120V

Supply Wire

Green ground

Wiring box

Ground to

mounting bracket

and downrod

BLACK

WHITE

BLACK

WHITE

GREEN

BLUE

Fig. 13

Tabla de contenidos

Idiomas:

Otros manuales de Admirador de Kichler Lighting

Kichler Lighting

Kichler Lighting Renew Select Patio Manual de usuario

Kichler Lighting

Kichler Lighting Lija Manual de usuario

Kichler Lighting

Kichler Lighting Decor Link Manual de usuario

Kichler Lighting

Kichler Lighting ERIS 337060 Manual de usuario

Kichler Lighting

Kichler Lighting Emerson HIGH COUNTRY Manual de usuario

Kichler Lighting

Kichler Lighting Industrial Fan Manual de usuario

Kichler Lighting

Kichler Lighting 52" RENEW ENERGY STAR Manual de usuario

Kichler Lighting

Kichler Lighting Terra Select Manual de usuario

Kichler Lighting

Kichler Lighting 35153 Manual

Kichler Lighting

Kichler Lighting Canfield 300117WH Manual de usuario

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Manual de usuario

Kichler Lighting

Kichler Lighting Imari 65 Manual de usuario

Kichler Lighting

Kichler Lighting 300457 Manual de usuario

Kichler Lighting

Kichler Lighting Deckard Manual de usuario

Kichler Lighting

Kichler Lighting 35162 Manual de usuario

Kichler Lighting

Kichler Lighting Kimberley Manual de usuario

Kichler Lighting

Kichler Lighting Compass 300322 Manual de usuario

Kichler Lighting

Kichler Lighting KAPONO Manual de usuario

Kichler Lighting

Kichler Lighting Renew Select Manual de usuario

Kichler Lighting

Kichler Lighting Monarch Manual de usuario

Kichler Lighting

Kichler Lighting Golden Iridescence Manual de usuario

Kichler Lighting

Kichler Lighting 300370 Manual de usuario

Kichler Lighting

Kichler Lighting IMARI 300365SBK Manual de usuario

Kichler Lighting

Kichler Lighting Lucian II 330241 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje