Keysight N9010B EXA Manual de instalación y operación

Option YAS

Y-Axis Screen Video Out

Keysight N9010B EXA and

N9020B MXA Signal Analyzers

N9048B PXE EMI Receiver

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9020-90272

Edition

Edition 1, October 2018

Supersedes February 2018

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9020-90272 3

Option YAS Installation Kit

Products Affected: N9010B EXA Signal Analyzer

N9020B MXA Signal Analyzer

N9048B PXE EMI Receiver

Serial Numbers: All

Options

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

0.5 Hours

4Installation Note N9020-90272

Option YAS Installation Kit

Introduction

This kit contains all of the instructions required to install Option YAS on Keysight EXA and MXA

signal analyzers and PXE EMI receivers. Option YAS enables the ANALOG OUT port to provide a

Y-Axis screen video output.

The rear panel ANALOG OUT port is present on all EXA and MXA signal analyzers and PXE EMI

receivers, however Option YAS must be enabled via a license file.

1. At the time of manufacture the hardware related to this option was fully

adjusted and the option performance was verified to be within its warranted

specifications. Within one year of the initial calibration date of the instrument

this option is fully calibrated with no further adjustment or verification testing.

To determine the initial calibration date, locate the original calibration

certificate that was shipped with the instrument at the time of purchase. The

Date of Calibration is printed on the original calibration certificate.

To ensure that this newly installed option has been installed properly, the

procedure that follows includes a functional check.

2. The latest revision of the X-Series signal analyzer software may be

downloaded from:

http://www.keysight.com/find/Xseries_software

3. This option is licensed for one instrument model/serial number combination.

The license key will only install on the designated instrument.

Installation Note N9020-90272 5

Option YAS Installation Kit

Contents

Tools Required for Installation

— Personal computer with internet access and USB port

— USB storage device with >2GB free memory

Tools Required for Manual Operation Verification

—Voltmeter

— Test cable, BNC (used to connect voltmeter to the analyzer rear panel ANALOG OUT)

— Banana plug to BNC adapter (used to connect voltmeter to BNC cable)

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Quantity Description Keysight Part Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

6Installation Note N9020-90272

Option YAS Installation Kit

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message similar to the one shown in Figure 2.

Figure 2 Successful License Installation

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the power on the signal analyzer.

2. Press System, Show System to display a list of installed options.

3. Verify that the newly installed option appears on the list.

Installation Note N9020-90272 7

Option YAS Installation Kit

Manually Verify Operation

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,

Center Frequency, key in 50 MHz. Press Span, Zero Span. You should see a flat line across the

display at −25 dBm.

3. Press AMPTD, Ref Level, and key in −25 dBm. The displayed signal level should be at the top

graticule line.

4. Press Input/Output, Output, Analog Out, Screen Video.

5. Connect a voltmeter, set to measure DC volts, to the analyzer rear panel ANALOG OUT

connector.

6. The voltmeter should measure 1V.

7. Increase the Ref Level to −15 dBm. The signal should drop one graticule division on screen and

the voltmeter reading should be 0.9 V.

8. This test is sufficient to determine if the output circuitry is working properly for all Analog Out

signal selections.

8Installation Note N9020-90272

Option YAS Installation Kit

Utilities, Adjustments, and Performance Verification Tests

Calibration Software and specified test equipment is required to perform the adjustments, and can

be used to automate the performance verification testing. Information on how to obtain this

software can be found at

http://www.keysight.com/find/calibrationsoftware

Utilities Required

None

Adjustments Required

None

Performance Testing Required

None

A full calibration is required to assure the instrument meets all specifications

The end user must ultimately determine whether they want a full calibration to be performed after

the installation of this upgrade or not. If a full calibration is required, arrangements regarding the

level of calibration must be made between the end user and the calibration provider.

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change

without notice.

Edition 1, October 2018

N9020-90272

www.keysight.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight

Keysight

Keysight EXA X-Series N9010A Manual de usuario

Keysight

Keysight PNA-L N5231A Manual de instalación y operación

Keysight

Keysight P-Series Guía de instalación

Keysight

Keysight N9342CN Manual de usuario

Keysight

Keysight 41800A Guía de inicio rápido

Keysight

Keysight N7744A Manual de usuario

Keysight

Keysight N2894A Manual de usuario

Keysight

Keysight u2722a Manual de usuario

Keysight

Keysight N9068A Manual de usuario

Keysight

Keysight E4981A Manual de usuario

Keysight

Keysight 537A Guía de inicio rápido

Keysight

Keysight M9005A Manual de usuario

Keysight

Keysight ENA Series Manual de usuario

Keysight

Keysight FieldFox B Series Manual de usuario

Keysight

Keysight N9923A Manual de usuario

Keysight

Keysight 53147A Instrucciones de funcionamiento

Keysight

Keysight N9040B Option 513 Manual de usuario

Keysight

Keysight 9020A Manual de instalación y operación

Keysight

Keysight U8903B Manual de usuario

Keysight

Keysight N2800A Manual de usuario

Keysight

Keysight PD1500A Guía del usuario

Keysight

Keysight N774 C Series Instrucciones de funcionamiento

Keysight

Keysight E5071C Manual de usuario

Keysight

Keysight W2630 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario