Keysight Technologies N9029AV01-V19 Manual de usuario

N9029AV01-V19, V1B, V2B

Signal Analyzer Frequency Extension Module and Accessories

The Keysight N9029AV01-V19, V1B and V2B Signal Analyzer Frequency Extension (SAX) Modules are manufactured

by Virginia Diodes, Inc. (VDI).

USER'S GUIDE

Notices

2016-2022

No part of this manual may be

reproduced in any form or by any

means (including electronic storage

and retrieval or translation into a

foreign language) without prior

agreement and written consent from

Keysight Technologies, Inc. as

governed by United States and

international copyright laws.

Trademark Acknowledgments

Manual Part Number

N9030-90061

Edition 11

Print Date: August 2022

Supersedes: February 2022

Printed in USA

Published by:

Keysight Technologies

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Warranty

THE MATERIAL CONTAINED IN THIS

DOCUMENT IS PROVIDED “AS IS,”

AND IS SUBJECT TO BEING

CHANGED, WITHOUT NOTICE, IN

FUTURE EDITIONS. FURTHER, TO

THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, KEYSIGHT

DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH

REGARD TO THIS MANUAL AND

ANY INFORMATION CONTAINED

HEREIN, INCLUDING BUT NOT

LIMITED TO THE IMPLIED

WARRANTIES OF

MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE.

KEYSIGHT SHALL NOT BE LIABLE

FOR ERRORS OR FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE

FURNISHING, USE, OR

PERFORMANCE OF THIS

DOCUMENT OR ANY INFORMATION

CONTAINED HEREIN. SHOULD

KEYSIGHT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT

WITH WARRANTY TERMS

COVERING THE MATERIAL IN THIS

DOCUMENT THAT CONFLICT WITH

THESE TERMS, THE WARRANTY

TERMS IN THE SEPARATE

AGREEMENT WILL CONTROL.

Technology Licenses

The hardware and/or software

described in this document are

furnished under a license and may be

used or copied only in accordance

with the terms of such license.

U.S. Government Rights

The Software is “commercial

computer software,” as defined

by Federal Acquisition Regulation

(“FAR”) 2.101. Pursuant to FAR

12.212 and 27.405-3 and

Department of Defense FAR

Supplement (“DFARS”) 227.7202,

the U.S. government acquires

commercial computer software

under the same terms by which

the software is customarily

provided to the public.

Accordingly, Keysight provides

the Software to U.S. government

customers under its standard

commercial license, which is

embodied in its End User License

Agreement (EULA), a copy of

which can be found at

http://www.keysight.com/find/sweula

The license set forth in the EULA

represents the exclusive authority

by which the U.S. government

may use, modify, distribute, or

disclose the Software. The EULA

and the license set forth therein,

does not require or permit,

among other things, that

Keysight: (1) Furnish technical

information related to

commercial computer software

or commercial computer

software documentation that is

not customarily provided to the

public; or (2) Relinquish to, or

otherwise provide, the

government rights in excess of

these rights customarily provided

to the public to use, modify,

reproduce, release, perform,

display, or disclose commercial

computer software or

commercial computer software

documentation. No additional

government requirements

beyond those set forth in the

EULA shall apply, except to the

extent that those terms, rights, or

licenses are explicitly required

from all providers of commercial

computer software pursuant to

the FAR and the DFARS and are

set forth specifically in writing

elsewhere in the EULA. Keysight

shall be under no obligation to

update, revise or otherwise

modify the Software. With

respect to any technical data as

defined by FAR 2.101, pursuant

to FAR 12.211 and 27.404.2 and

DFARS 227.7102, the U.S.

government acquires no greater

than Limited Rights as defined in

FAR 27.401 or DFAR 227.7103-5

(c), as applicable in any technical

data.

Safety Notices

A CAUTION notice denotes a hazard. It

calls attention to an operating

procedure, practice, or the like that,

if not correctly performed or adhered

to, could result in damage to the

product or loss of important data. Do

not proceed beyond a CAUTION

notice until the indicated conditions

are fully understood and met.

A WARNING notice denotes a hazard.

It calls attention to an operating

procedure, practice, or the like that,

if not correctly performed or adhered

to, could result in personal injury or

death. Do not proceed beyond a

WARNING notice until the indicated

conditions are fully understood and

met.

Keysight Technologies

N9029AV01-V19, V1B and V2B

Signal Analyzer Frequency Extension Module

and Accessories

The Keysight N9029AV01-V19, V1B and V2B Signal Analyzer Frequency Extension (SAX)

Modules are manufactured by Virginia Diodes, Inc. (VDI). The Mixer/Amplifier/Multiplier Chain

(MixAMC) modules are for use with the Keysight X-Series Signal Analyzer with the External

Mixer Option (EXM), required.

The modules provide high performance broadband frequency down-conversion, and for

modules with Option UDC, frequency up-conversion. The modules can be used with

microwave signal analyzers to extend the frequency range into the THz range. These modules

achieve low conversion loss and excellent noise figure. Refer to the VDI User’s Guide included

on the USB drive.

For more information, see the Product Manual at https://www.vadiodes.com/images/

Products/SAX/SAX_Product_Manual/VDI-731_SAX_Product_Manual.pdf.

For specifications, see the VDI web page at https://www.vadiodes.com/images/Products/

SAX/VDI_SAX_Specifications_20201110.pdf.

The cables and power supply will be included with the module in the transport case. Cutouts

have been created for the accessories within the transport case, simply remove the foam insert.

Accessories (amplifiers, attenuators, filters, and waveguide sections) available for order1.

Cable VDI Module USB Drive AC Power Cable

ansport Case Power Supply

Accessories

(Optional)

1. To order accessories, see Accessories and Information on page 12. For the Keysight Millimeter Wave Frequency

Extenders, Technical Overview document, visit http://literature.cdn.keysight.com/litweb/pdf/5991-3161EN.pdf

Keysight Technologies N9030-90061

Before using your SAX module, please read all documentation from VDI

(included on the USB drive).

Typical Connection Diagram for External Mixing

Table 1 SAX Modules

Keysight

Model

VDI

Model

Frequency

(GHz)

N9029AV01 WR1.0SAX 750 to 1100

N9029AV1B WR1.5SAX 500 to 750

N9029AV2B WR2.8SAX 260 to 400

N9029AV02 WR2.2SAX 325 to 500

N9029AV03 WR3.4SAX 220 to 330

N9029AV05 WR5.1SAX 140 to 220

N9029AV06 WR6.5SAX 110 to 170

N9029AV08 WR8.0SAX 90 to 140

N9029AV10 WR10SAX 75 to 110

N9029AV12 WR12SAX 60 to 90

N9029AV15 WR15SAX 50 to 75

N9029AV04 WR4.3SAX 170 to 260

Be aware of the power level applied to the waveguide input. Non-warrantied

damage to the internal mixer can occur if the power level is at or above the

damage level specified in the VDI User's Guide for "RF Input."

The product serial number is the OEM serial number SAXxxxx (xxxx =

numbers in the OEM serial number) assigned by Virginia Diodes, Inc.

Refer to the label on the product for the serial number.

N9029AV19WR19SAX 40 to 60

Keysight Technologies N9030-90061

Table 2 SAX Options

Option Description

DC9 Standard SAX with 9 VDC supply

UDC Adds IF input data (on USB) for frequency up-conversion

D48 Adds data on USB down to 48 GHz (for N9029AV15 only)

D73 Adds data on USB down to 73 GHz (for N9029AV10 only)

HS0 DC9 SAX with high sensitivity

MCF Adds Mixer Cal Files for Automotive Radar Solution (for N9029AV12 only)

Keysight Technologies N9030-90061

SAX Label

There is data on the USB drive that can be used to create a corrections file to improve amplitude

accuracy.

Always use the information printed on the SAX label of your module.

When using the LO/IF (L) Input (External Mixing), use LO (L): N= X, with

"X" being the multiplication factor value shown on your SAX label.

When using the LO/IF (H) Input, use LO (H): N= X, with "X" being the

multiplication factor value shown on your SAX label.

On the SAX label, the multiplication

factor values are circled. This is an

example only; the actual values will

vary.

•

When using your signal analyzer with the SAX, you must set the analyzer to external mixing, including

harmonic and Doubler Switched parameters.

For the N90x0A Models:

[Input/Output] > External Mixer > External Mixer > Ext Mix Setup > Edit Harmonic Table >

[Enter] (or select OK).

Table Type > Doubler Switching > Harmonic > [N] > Enter N value (see SAX label on module, or see VDI

document, for N value)

For the N90x0B Models:

[Input/Output] > Select Input > External Mixer > External Mixer Setup > Table Type > Doubler Switching

>Harmonic (under Harmonic Table) > Enter N value (see SAX label on module, or see VDI document, for

N value)

For improved spurious response:

Change the number of sweep points:

[Sweep/Control] > Points > [40001]

Multi-Touch Sweep > Sweep Config > Points > [40001]

Reduce resolution bandwidth:

[BW] > Res BW > [300 kHz]

Turn on Signal ID:

[Input/Output] > External Mixer > Signal ID > On > Signal ID Mode > Image Suppress

Multi-Touch Input > Output > Signal ID > On > Signal ID Mode > Image Suppress

•

Keysight Technologies N9030-90061

Frequency Up-Converter Operation

The option UDC has an IF input and 9 volt connections for external devices. For frequency

up-conversion, the left jumper is to be removed.

The IF input frequency will be up-converted to the multiplication factor of the LO input (H) ++

IF input {N x LO input (H) + IF input = waveguide output frequency}. Refer to the VDI

User's Guide for frequencies and power levels.

1. Connect RF source to LO input (H), such as an E8257D PSG.

2. Connect RF signal to be up-converted to the IF input, such as an E8257D PSG.

Voltage Bias Port LO input (H)

IF input

Other modes of operation may be found in the VDI documentation.

Keysight Technologies N9030-90061

Power Requirements

•Voltage and/or range (V): 100-240 Vac (AC input for AC/DC adapter), 9 Vdc (input

for module)

•Frequency and/or range (Hz): 50-60 Hz (AC input for AC/DC adapter)

•Power in Watts, VA or Current (A): 1.2 A max (input for AC/DC adapter), 4 A (input

for module)

The instrument can operate with mains supply voltage fluctuations up to

± 10% of the nominal voltage.

Environmental Conditions

•For indoor use only

This product is designed for use in INSTALLATION CATEGORY II and

POLLUTION DEGREE 2.

Install the instrument so that the detachable power cord is readily identifiable and is

easily reached by the operator. The detachable power cord is the instrument

disconnecting device. It disconnects the mains circuits from the mains supply before

other parts of the instrument. Alternatively, an externally installed switch or circuit

breaker (which is readily identifiable and is easily reached by the operator) may be

used as a disconnecting device.

The input terminals for this product are classified as Measurement

Category None.

Cleaning connectors with alcohol shall only be done with the

instrument's power cord removed and in a well-ventilated area.

Allow all residue alcohol moisture to evaporate and the fumes to

dissipate prior to energizing the instrument.

Cleaning

To prevent electrical shock, disconnect the instrument from mains

before cleaning. Use a dry cloth or one slightly dampened with water

to clean external case parts. Do not attempt to clean internally.

Keysight Technologies N9030-90061

Before using your converter module, please read all documentation from

VDI (included on the USB drive). It is important to follow the General

Operating Procedures and Guidelines section.

This product has been designed and tested in accordance with accepted

industry standards and has been supplied in a safe condition. The

documentation contains information and warnings that must be followed

by the user to ensure safe operation and to maintain the product in a safe

condition.

Safety and Information

Only Keysight approved accessories shall be used.

Use the Keysight supplied power cord or one with the same or better

electrical rating.

No operator serviceable parts inside. Refer servicing to qualified

personnel. To prevent electrical shock do not remove covers.

The Mains wiring and connectors shall be compatible with the

connector used in the premise electrical system. Failure to ensure

adequate earth grounding by not using the correct components may

cause product damage and serious injury.

This instrument has auto-ranging line voltage input. Be sure the

supply voltage is within the specified range and voltage fluctuations

do not to exceed 10 percent of the nominal supply voltage.

The main power cord can be used as the system disconnecting device. It

disconnects the mains circuits from the mains supply.

If this product is not used as specified, the protection provided by the

equipment could be impaired. This product must be used in a normal

condition (in which all means for protection are intact) only.

Safety of any system incorporating the equipment is the responsibility

of the assembler of the system.

Keysight Technologies N9030-90061

Instrument Markings

Listed below are definitions for the markings that may be found on the product.

IP 2 0

The instruction documentation symbol. The product is marked with this symbol when it is

necessary for the user to refer to the instructions in the documentation.

The AC symbol indicates the required nature of the line module input power.

This symbol indicates separate collection for electrical and electronic equipment,

mandated under EU law as of August 13, 2005. All electric and electronic equipment are

required to be separated from normal waste for disposal (Reference WEEE Directive,

2002/96/EC).

This symbol indicates that the power line switch is ON.

This symbol indicates that the power line switch is in the OFF position.

The instrument has been designed to meet the requirements of IP 2 0 for egress and

operational environment.

The RCM mark is a registered trademark of the Australian Communications and Media

Authority.

Indicates the time period during which no hazardous or toxic substance elements are

expected to leak or deteriorate during normal use. Forty years is the expected useful life

of the product.

The CE mark is a registered trademark of the European Community.

The Keysight email address s required by EU directives applicable to our product.

This is a symbol of an Industrial Scientific and Medical Group 1 Class A product (CISPR

11, Clause 5).

This is a marking to indicate product compliance with the Canadian Interference-Causing

Equipment Standard (ICES-001). Cet appareil ISM est conforme à la norme NMB du

Canada.

This symbol on all primary and secondary packaging indicates compliance to China

standard GB 18455-2001.

South Korean Certification (KC) mark; includes the marking's identifier code which

follows this format: MSIP-REM-YYY-ZZZZZZZZZZZZZZ.

[email protected]

•IEC/EN 61326-1

•CISPR Pub 11 Group 1, Class A

Caution: This equipment is not intended for use in residential environments and may not provide

adequate protection to radio reception in such environments.

•AS/NZS CISPR 11

•ICES/NMB-001

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme a la norme NMB-001 du Canada.

ICES/NMB-001

To find a current Declaration of Conformity for a specific Keysight product, go to:

http://regulations.about.keysight.com/DoC/search.htm

Safety

Complies with the essential requirements of the European Low Voltage Directive.

EMC

Complies with the essential requirements of the European EMC Directive as well as current editions of the

following standards (dates editions are cited in the Declaration of Conformity):

Keysight Technologies N9030-90061

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight Technologies

Keysight Technologies

Keysight Technologies U5309A Guía del usuario

Keysight Technologies

Keysight Technologies E5072A Manual de usuario

Keysight Technologies

Keysight Technologies E5052B Manual del propietario

Keysight Technologies

Keysight Technologies UXA Manual de instalación y operación

Keysight Technologies

Keysight Technologies P939 A Series Manual de usuario

Keysight Technologies

Keysight Technologies N9000B Manual de usuario

Keysight Technologies

Keysight Technologies MXA N9020A-508 Manual de usuario

Keysight Technologies

Keysight Technologies N9030B Manual de instalación y operación

Keysight Technologies

Keysight Technologies N9020A Manual de instalación y operación

Keysight Technologies

Keysight Technologies EXA N9010B Manual de instalación y operación

Keysight Technologies

Keysight Technologies B2981A Guía de instalación

Keysight Technologies

Keysight Technologies U5303A Guía del usuario

Keysight Technologies

Keysight Technologies U1084A Guía del usuario

Keysight Technologies

Keysight Technologies FieldFox Manual de usuario

Keysight Technologies

Keysight Technologies N4373D Manual de usuario

Keysight Technologies

Keysight Technologies U4164A Manual de usuario

Keysight Technologies

Keysight Technologies N9340B Manual de usuario

Keysight Technologies

Keysight Technologies LTE Manual de instalación

Keysight Technologies

Keysight Technologies N9344C Manual de usuario

Keysight Technologies

Keysight Technologies U1733C Manual de usuario

Keysight Technologies

Keysight Technologies EXA Manual de instalación y operación

Keysight Technologies

Keysight Technologies E4981A Manual de usuario

Keysight Technologies

Keysight Technologies 6811C Instrucciones de funcionamiento

Keysight Technologies

Keysight Technologies N774 C Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario