Keysight Technologies EXA N9010B Manual de instalación y operación

Option HL3, 2nd IF Output (CR3) and

Arbitrary IF Output (CRP) Upgrade Kit

Keysight Technologies

N9010B EXA Signal Analyzer

N9020B MXA Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9010-90066

Edition

Edition 1, September 2018

Supersedes February 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9010-90066 3

Option HL3, 2nd IF Output (CR3) and Arbitrary IF Output (CRP) Upgrade Kit

Option HL3, 2nd IF Output (CR3) and Arbitrary IF Output (CRP)

Upgrade Kit

Software and test equipment is required for making adjustments and for performance verification

testing.

Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this

upgrade, the end user must ultimately determine whether they want this service or not. If a full

calibration is required, arrangements regarding the level of calibration must be made between the

end user and the calibration provider

Products Affected: N9010B, EXA Signal Analyzer

N9020B, MXA Signal Analyzer

Serial Numbers: All

Options CR3, CRP

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysighta

( ) Customer

a. To ensure that these newly installed options are functioning properly, the procedure that follows

includes the requirement of performing certain adjustments and performance verification tests.

However, the completion of these tests does not guarantee that the instrument meets all advertised

specifications.

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

2.0 Hours

4.5 Hours

3.5 Hours

4Installation Note N9010-90066

Introduction

This kit includes parts to upgrade any EXA or MXA signal analyzer, regardless of age, to add options

CR3, 2nd IF Output, and CRP, Arbitrary IF Output. As a result, some parts included in this kit will not

be needed for upgrading some analyzers (newer analyzers require fewer parts to be changed). Also,

some parts might not be necessary if other certain options are already installed.

In addition to installing the hardware to support options CR3 and CRP, licenses for the following

options will also be installed (the 'x' is either 1 for EXA or 2 for MXA):

— N90x0A-CR3, Connector Rear, 2nd IF Output

— N90x0A-CRP, Connector Rear, Arbitrary IF Output

The installation procedure begins with an “inventory” of the analyzer serial number,

currently-installed options, installed hardware, and software version. This information will be used

to determine which sub-procedures, if any, can be skipped.

Installation Note N9010-90066 5

Introduction

Contents

Quantity Description Keysight Part Number

1 A15 Front End Controller w/ IF MUX N9020-60172

1 Opt HL3 Cable Kit with Wire Markers

(includes cables W36, W37, and W39, listed below)

N9020-60170

1 Cable Assembly, Coaxial 530 mm LG (W37) 8121-1401awith ends labeled '900' and '100'

a. This cable is included in the Opt HL3 Cable Kit with Wire Markers, p/n N9020-60170

1 Cable Assembly, Coaxial 240 mm LG (W36) 8121-1862awith ends labeled '902' and '7'

1 Cable Assembly, Coaxial 525 mm LG (W39) 8121-2028awith one end labeled '1100'

14 Screw M3 x 0.5 (6 mm long) Flathead 0515-1946

3 Cable Tie, Self-Locking, Nylon Gray 1400-0249

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

6Installation Note N9010-90066

Introduction

Tools Required

— T-10 TORX Driver

— T-20 TORX Driver

— 5/16-inch torque wrench

— 9/16-inch nut driver

— Scissors or knife

—Diagonalcutters

— Keysight Calibration and Adjustment Software, N7814A (revision E.16.00 or later)

— Test equipment and computer supported by the X- Series Performance Tests and Adjustment

Software

— EXA or MXA Signal Analyzer Service Guide (as appropriate). This manual is available online at

the following URL:

www.keysight.com/find/N9010B_service_guide

www.keysight.com/find/N9020B_service_guide

— Microsoft Windows based personal computer with internet access and USB port

— USB storage device with >2GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

Before you disassemble the instrument, turn the power switch to Standby. After the instrument

has completely shut down, unplug the instrument. Failure to unplug the instrument can result in

personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

Installation Note N9010-90066 7

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show System. Make note of the

following information from the Show System screen:

Product Number _______________

Serial Number _______________

Instrument S/W Revision _______________

3. Check for the presence of the options listed below in the Show System screen (“x” is 1 for an

EXA and 2 for an MXA). Put a check mark or “X” after each option listed below that appears in

the Show System menu.

N90x0B-503 _____

N90x0B-CR3 _____

N90x0B-CRP _____

N90x0B-B40 _____

N90x0B-DP2 _____

N90x0B-MPB _____

4. On the analyzer, press System, Show Hardware. Note the Part #, Matl Rev, Rev, OF Rev, and

Hw Id of the Front End Controller in the table below.

5. Refer to the data in step 3 and step 4 above. If the analyzer has N90x0B-B40, N90x0B-DP2,

and/or N90x0B-MPB installed, verify that it also has a Front End Controller with a Hw Id of 75.

If the Front End Controller has a Hw Id of 75, you do not need this upgrade kit, since the

necessary hardware is already present. Refer instead to upgrade products N90x0BU-CR3 and

N90x0BU-CRP.

Assembly Name Part # Matl Rev Rev OF Rev Hw Id

Front End Controller

8Installation Note N9010-90066

Installation Procedure

6. Refer to the data in step 3 and step 4 above. If the analyzer has N90x0B-CR3 and/or

N90x0B-CRP installed, verify that it also has a Front End Controller with Hw Id of 75. If the

Front End Controller has a Hw Id of 75, you do not need this upgrade kit, since the necessary

hardware is already present. Refer instead to upgrade products N90x0BU-CR3 and

N90x0BU-CRP.

7. Refer to the data in step 3 and step 4 above. If the analyzer has N9010B-532 or N9010B-544

installed, verify that it also has a Front End Controller with Hw Id of 75. If the Front End

Controller has a Hw ID of 75, you do not need this upgrade kit, since the necessary hardware is

already present. Refer instead to upgrade products N9010BU-CR3 and N9010BU-CRP.

8. Refer to the data in step 3 and step 4 above. If the analyzer has N90x0B-CR3 and/or

N90x0B-CRP installed, and the Front End Controller does not have a Hw Id of 75, proceed to

the next step. Although the licenses for N90x0B-CR3 and/or N90x0B-CRP are installed, the

necessary hardware has not been installed.

Update Instrument Software

Go to the following website and determine whether or not the analyzer has the latest instrument

software already installed:

http://www.keysight.com/find/xseries_software

If the analyzer does not have the latest instrument software already installed, download and install

the latest version.

Installation Note N9010-90066 9

Installation Procedure

Licensing the New Options

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to one of the analyzer’s USB ports. Connect a mouse to

another USB port. Windows will detect the new hardware and may display the configuration

menu shown in Figure 1. This menu may be configured according to your preferences.

Figure 1 USB Storage Device Configuration Menu

7. The analyzer will automatically consume the License File. (This may take a few minutes) When

the License File is consumed the Keysight License Manager will display a “Successful License

Installation” message similar to the one shown in Figure 2.

Figure 2 Successful License Installation

10 Installation Note N9010-90066

Installation Procedure

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the License Installation

1. Before the licenses will be recognized, the XSA application must be restarted. Press System,

Exit Program. An Exit Analyzer dialog box will appear; press Enter to confirm the exit.

2. Double-click on the LaunchXSA icon on the Windows desktop. Wait for the XSA application to

finish starting (the analyzer should be sweeping).

3. Press System, Show System on the analyzer to display a list of installed options. You should

see the following options listed (“x” is 1 for an EXA and 2 for an MXA).

—N90x0B-CR3 Connector Rear, 2nd IF Output

—N90x0B-CRP Connector Rear, Arbitrary IF Output

Otros manuales para EXA N9010B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight Technologies

Keysight Technologies

Keysight Technologies N5511A-K26 Manual de usuario

Keysight Technologies

Keysight Technologies N9020B Manual de instalación y operación

Keysight Technologies

Keysight Technologies N437 Series Instrucciones de instalación y funcionamiento

Keysight Technologies

Keysight Technologies X Series Manual de usuario

Keysight Technologies

Keysight Technologies E4980A Manual del operador

Keysight Technologies

Keysight Technologies N432A Manual de usuario

Keysight Technologies

Keysight Technologies 11590B Manual de servicio

Keysight Technologies

Keysight Technologies FieldFox N9927-90002 Manual de usuario

Keysight Technologies

Keysight Technologies X Series Manual del propietario

Keysight Technologies

Keysight Technologies 85059B Manual de servicio

Keysight Technologies

Keysight Technologies E2655C Manual de usuario

Keysight Technologies

Keysight Technologies 86120B Manual de usuario

Keysight Technologies

Keysight Technologies N77 Series Manual de usuario

Keysight Technologies

Keysight Technologies N5252A Manual de usuario

Keysight Technologies

Keysight Technologies N2797A Manual de usuario

Keysight Technologies

Keysight Technologies ENA Series Guía de inicio rápido

Keysight Technologies

Keysight Technologies M8131A Manual de usuario

Keysight Technologies

Keysight Technologies E4980A Guía de inicio rápido

Keysight Technologies

Keysight Technologies B2980A Series Manual de usuario

Keysight Technologies

Keysight Technologies N5221B Manual de usuario

Keysight Technologies

Keysight Technologies U1084A Guía del usuario

Keysight Technologies

Keysight Technologies N2893A Manual de usuario

Keysight Technologies

Keysight Technologies N9029AV01-V15 Manual de usuario

Keysight Technologies

Keysight Technologies E5260 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario