Keysight Technologies 34980A Manual de usuario

Keysight 34980A Data

Acquisition System

Service Guide

2 Keysight 34980A Service Guide

Notices

No part of this manual may be

reproduced in any form or by any

means (including electronic storage

and retrieval or translation into a

foreign language) without prior

agreement and written consent from

Keysight Technologies as governed by

United States and international

Trademarks

Microsoft and Windows are U.S.

registered trademarks of Microsoft

Corporation.

Manual Part Number

34980-90010

Edition

Edition 9, August 20, 2019

Printed in:

Printed in Malaysia

Published by:

Keysight Technologies

Bayan Lepas Free Industrial Zone,

11900 Penang, Malaysia

Technology Licenses

The hardware and/or software

described in this document are

furnished under a license and may be

used or copied only in accordance with

the terms of such license.

Declaration of Conformity

Declarations of Conformity for this

product and for other Keysight

products may be downloaded from the

Web. Go to http://www.keysight.com/

go/conformity. You can then search by

product number to find the latest

Declaration of Conformity.

U.S. Government Rights

The Software is “commercial computer

software,” as defined by Federal

Acquisition Regulation (“FAR”) 2.101.

Pursuant to FAR 12.212 and 27.405-3

and Department of Defense FAR

Supplement (“DFARS”) 227.7202, the

U.S. government acquires commercial

computer software under the same

terms by which the software is

customarily provided to the public.

Accordingly, Keysight provides the

Software to U.S. government

customers under its standard

commercial license, which is embodied

in its End User License Agreement

(EULA), a copy of which can be found

at http://www.keysight.com/find/

sweula. The license set forth in the

EULA represents the exclusive authority

by which the U.S. government may use,

modify, distribute, or disclose the

Software. The EULA and the license set

forth therein, does not require or

permit, among other things, that

Keysight: (1) Furnish technical

information related to commercial

computer software or commercial

computer software documentation that

is not customarily provided to the

public; or (2) Relinquish to, or

otherwise provide, the government

rights in excess of these rights

customarily provided to the public to

use, modify, reproduce, release,

perform, display, or disclose

commercial computer software or

commercial computer software

documentation. No additional

government requirements beyond

those set forth in the EULA shall apply,

except to the extent that those terms,

rights, or licenses are explicitly required

from all providers of commercial

computer software pursuant to the FAR

and the DFARS and are set forth

specifically in writing elsewhere in the

EULA. Keysight shall be under no

obligation to update, revise or

otherwise modify the Software. With

respect to any technical data as

defined by FAR 2.101, pursuant to FAR

12.211 and 27.404.2 and DFARS

227.7102, the U.S. government

acquires no greater than Limited Rights

as defined in FAR 27.401 or DFAR

227.7103-5 (c), as applicable in any

technical data.

Warranty

THE MATERIAL CONTAINED IN THIS

DOCUMENT IS PROVIDED “AS IS,”

AND IS SUBJECT TO BEING

CHANGED, WITHOUT NOTICE, IN

FUTURE EDITIONS. FURTHER, TO THE

MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, KEYSIGHT

DISCLAIMS ALL WARRANTIES, EITHER

EXPRESS OR IMPLIED, WITH REGARD

TO THIS MANUAL AND ANY

INFORMATION CONTAINED HEREIN,

INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. KEYSIGHT

SHALL NOT BE LIABLE FOR ERRORS

OR FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE

FURNISHING, USE, OR

PERFORMANCE OF THIS DOCUMENT

OR OF ANY INFORMATION

CONTAINED HEREIN. SHOULD

KEYSIGHT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT

WITH WARRANTY TERMS COVERING

THE MATERIAL IN THIS DOCUMENT

THAT CONFLICT WITH THESE TERMS,

THE WARRANTY TERMS IN THE

SEPARATE AGREEMENT SHALL

CONTROL.

Safety Information

CAUTION

A CAUTION notice denotes a hazard. It

calls attention to an operating

procedure, practice, or the like that, if

not correctly performed or adhered to,

could result in damage to the product

or loss of important data. Do not

proceed beyond a CAUTION notice

until the indicated conditions are fully

understood and met.

WARNING

A WARNING notice denotes a hazard. It

calls attention to an operating

procedure, practice, or the like that, if

not correctly performed or adhered to,

could result in personal injury or death.

Do not proceed beyond a WARNING

notice until the indicated conditions are

fully understood and met.

Keysight 34980A Service Guide 3

Safety Symbols

The following symbols on the instrument and in the documentation indicate

precautions which must be taken to maintain safe operation of the instrument.

Safety Considerations

Read the information below before using this instrument.

The following general safety precautions must be observed during all phases of

operation, service, and repair of this instrument. Failure to comply with these

precautions or with specific warnings elsewhere in this manual violates safety

standards for design, manufacture, and intended use of the instrument. Keysight

Technologies assumes no liability for the customer’s failure to comply with these

requirements.

General

Do not use this products in any manner not specified by the manufacturer. The

protective features of this product may be impaired if it is used in a manner not

specified in the operation instructions.

Before Applying Power

Verify that all safety precautions are taken. Make all connections to the unit before

applying power.

Alternating current (AC) Frame or chassis (ground) terminal

Standby supply. Unit is not completely

disconnected from ac mains when

switch is off

Caution, risk of electric shock

Caution, risk of danger (refer to this

manual for specific Warning or Caution

information)

4 Keysight 34980A Service Guide

Ground the Instrument

This product is provided with protective earth terminals. To minimize shock

hazard, the instrument must be connected to the ac power mains through a

grounded power cable, with the ground wire firmly connected to an electrical

ground (safety ground) at the power outlet. Any interruption of the protective

(grounding) conductor or disconnection of the protective earth terminal will cause

a potential shock hazard that could result in personal injury.

Do Not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable gases or fumes.

Do Not Remove the Instrument Cover

Only qualified, service-trained personal who are aware of the hazards involved

should remove instrument covers. Always disconnect the power cable and any

external circuits before removing the instrument cover.

Do Not Modify the Instrument

Do not install substitute parts or perform any unauthorized modification to the

product. Return the product to an Keysight Sales and Service Office for service

and repair to ensure that safety features are maintained.

In Case of Damage

Instruments that appear damaged or defective should be made inoperative and

secured against unintended operation until they can be repaired by qualified

service personnel.

Keysight 34980A Service Guide 5

Environmental Conditions

Keysight 34980A is designed for indoor use in an installation category II and low

condensation environment. Do not use in locations where conductive dust or

electrolytic salt dust may be present. Table below shows the general

environmental conditions for this instrument. Refer to the product data sheet at

https://literature.cdn.keysight.com/litweb/pdf/5989-1437EN.pdf for more

information on the instrument general specifications.

General specifications Requirement

Temperature Operating condition: 0°C to 55°C

Storage condition: -40°C to 70°C

Humidity Up to 80% R.H. at 31°C (non-condensing), decreasing

linearly to 50% R.H. at 40°C (non-condensing)

Altitude Up to 2,000 m

Pollution degree 1 or 2

NOTE

When used in pollution degree 1 conditions, the maximum voltage rating for the

Analog Buses is 300V. When used in pollution degree 2 conditions, the

maximum voltage rating is 100V. If conditions change, ensure that condensation

has evaporated and the instrument has thermally stabilized until pollution

degree 1 conditions are restored before turning on power to the equipment.

NOTE

Pollution Degree 1: No pollution or only dry, non-conductive pollution occurs.

The pollution has no influence (on insulation) (IEC 61010-1 2nd Edition).

Pollution Degree 2: Normally only non-conductive pollution occurs.

Occasionally, a temporary conductivity (leakage current between isolated

conductors) caused by condensation can be expected (IEC 61010-1

2nd Edition).

6 Keysight 34980A Service Guide

Waste Electrical and Electronic Equipment (WEEE) Directive

2002/96/EC

This instrument complies with the WEEE Directive (2002/96/EC) marking

requirement. This affixed product label indicates that you must not discard this

electrical or electronic product in domestic household waste.

Product category:

With reference to the equipment types in the WEEE directive Annex 1, this

instrument is classified as a “Monitoring and Control Instrument” product.

The affixed product label is as shown below.

Do not dispose in domestic household waste.

To return this unwanted instrument, contact your nearest Keysight Service Center,

or visit http://about.keysight.com/en/companyinfo/environment/takeback.shtml

for more information.

Sales and Technical Support

To contact Keysight for sales and technical support, refer to the support links on

the following Keysight websites:

–www.keysight.com/find/34980a

(product-specific information and support, software and

documentation updates)

–www.keysight.com/find/assist

(worldwide contact information for repair and service)

Keysight 34980A Service Guide 7

Front Panel at a Glance

1On/Standby switch

2Utility menu contains settings for Remote I/O (LAN, GPIB, and USB), Date and Time, and other

system-related instrument parameters

WARNING

This switch is standby only. To disconnect the mains from

the instrument, remove the power cord.

8 Keysight 34980A Service Guide

3Store/recall menu allows you to save and recall up to six instrument setups

4Control keys directly control module actions

5Number keypad enters numerical characters

6Exponent

7Cancel key exits a menu without saving changes

8Arrow keys move cursor positions

9Knob enters alphanumeric characters, selects slots, channels, and navigates menus

10 Enter key steps you through a menu or saves number entries

11 Running a program puts the display into “remote” and disables the front panel keys. Local takes you out

of “remote” mode and enables the front panel keys.

12 Configure keys select functions and set function parameters

13 Measure keys execute and monitor measurements. Depending on which measurement key you use, you

can have complete/direct control over the switching and measurement operation, or you can have the

34980A automatically control these to capture the desired data.

CAUTION

For proper instrument function, Channel monitor must be

turned OFF when the state is stored and Auto recall is

enabled. If the Channel monitor is turned ON, the front

panel may freeze, If the front panel is frozen, all plug-in

modules must be removed and the auto-recall function

turned OFF to restore the instrument back to its initial

working state.

Keysight 34980A Service Guide 9

Rear Panel at a Glance

Access to Analog Buses (shown with cover installed). For pinout, see page 12.

Module installed in slot 1

Slot identifier

10 Keysight 34980A Service Guide

Module ground screw

Slot cover over slot 2

AC power connector

LAN connector (10Base T/100Base Tx)

USB 2.0 connector

External trigger input. For pinout, see page 11.

Internal DMM option mark. If you ordered the internal DMM option, the circle is

marked black.

IEEE 488.2 GPIB Connector

Chassis ground screw

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight Technologies

Keysight Technologies

Keysight Technologies LTE Manual de instalación

Keysight Technologies

Keysight Technologies CXA Manual de instalación y operación

Keysight Technologies

Keysight Technologies E4990A Manual de usuario

Keysight Technologies

Keysight Technologies N5241B Manual de instalación y operación

Keysight Technologies

Keysight Technologies N5245-60106 Manual de instalación y operación

Keysight Technologies

Keysight Technologies 16089A Manual de operación

Keysight Technologies

Keysight Technologies N5221A Manual de usuario

Keysight Technologies

Keysight Technologies N9000A Manual de instalación y operación

Keysight Technologies

Keysight Technologies E5868A Instrucciones de montaje

Keysight Technologies

Keysight Technologies N9321C Manual de usuario

Keysight Technologies

Keysight Technologies W3301A Manual de usuario

Keysight Technologies

Keysight Technologies B2980A Series Manual de usuario

Keysight Technologies

Keysight Technologies Streamline Series Manual de usuario

Keysight Technologies

Keysight Technologies E5400-Pro Series Manual de usuario

Keysight Technologies

Keysight Technologies 34959A Manual de usuario

Keysight Technologies

Keysight Technologies UXA N9040B Manual de usuario

Keysight Technologies

Keysight Technologies U4431A Manual de usuario

Keysight Technologies

Keysight Technologies B2981A Guía de instalación

Keysight Technologies

Keysight Technologies N778 C Series Instrucciones de funcionamiento

Keysight Technologies

Keysight Technologies U4205A Manual de usuario

Keysight Technologies

Keysight Technologies E5061B Manual de usuario

Keysight Technologies

Keysight Technologies X Series Manual de instalación y operación

Keysight Technologies

Keysight Technologies N9030B Manual de instalación y operación

Keysight Technologies

Keysight Technologies 8990B Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario