KERN DLB A01N Manual de usuario

KERN & Sohn GmbH

Ziegelei 1

D-72336 Balingen

E-Mail: info@kern-sohn.com

Phone: +49-[0]7433- 9933-0

Fax: +49-[0]7433-9933-149

Internet: www.kern-sohn.com

Operating instructions

Temperature Calibrating set

KERN DLB_A01N

Version 1.1

2020-12

DLB_A01N-BA-e-2011

2 DLB_A01N-BA-e-2011

KERN DLB_A01N

Version 1.12020-12

Operating manual

Temperature Calibrating set

Contents

1Preparation ......................................................................................................... 3

2TDLG 160-3-A ..................................................................................................... 4

2.1 Calibration of temperature value ...................................................................... 4

2.2 Adjustment of temperature value ..................................................................... 5

3DLB 160-3 ........................................................................................................... 7

3.1 C alibration of temperature value ...................................................................... 8

3.2 Adjustment of temperature value ..................................................................... 9

DLB_A01N-BA-e-2011 3

1 Preparation

We recommend sometimes to check the temperature value of the models using the

optional temperature calibrating set DLB-A01N.

Before you do this, allow the device to

cool down for at least 30 minutes after the last heating phase.

Install the temperature-calibration set acc. to illustration.



Switch-on the moisture analyzer.

Close heating cover.

For further information on how to operate the moisture meter please refer to the

operating instructions enclosed with each model.

4 DLB_A01N-BA-e-2011

2 TDLG 160-3-A

2.1 Calibration of temperature value

During temperature calibration only a check is carried out, i.e. no values are changed.

1. In the start display press the F1-key, the main menu will appear.

2. Press to select the menu item <6 - Temperature Test> .

3. Acknowledge by .

Press to acknowledge the following instruction how to use a temperature

calibration set DLB-A01N. The current setting is displayed

4. Select desired test temperature with and acknowledge by .

The device heats up the set temperature.

5. After 15 minutes the test is finished, an acoustic signal sounds. Compare the test

temperature with the displayed temperature of the DLB-A01N. If the two values

do not match, we recommend a temperature adjustment, see chap. 2.2

6. Press to cancel the calibration.

DLB_A01N-BA-e-2011 5

2.2 Adjustment of temperature value

If in temperature calibration the admitted divergence is exceed or not reached, the

temperature of the instrument can be adjusted as described below.

1. In the start display press the F1-key, the main menu will appear.

2. Press to select the menu item <7 – Heater Calibration> and confirm by

3. Confirm the inquiries <Are you sure> and the following instruction how to use a

temperature calibration set DLB-A01N by .

The current settings of the both temperature points T-lo / T-hi are displayed.

4. Press to select the desired test temperature and press to

select between <T-lo> and <T-hi>. Acknowledge with .

5. Press , the first heating phase is started.

6 DLB_A01N-BA-e-2011

6. Temperature calibration for the first point takes 15 min. Compare the temperature

displayed on the DLB-A01N with that of the moisture analyzer.

If the two values do not match, read off the value at the temperature calibration

set and enter with the help of .

7. Confirm by , the second heating phase is started.

8. Temperature calibration for the second point takes 15 min. Compare the

temperature displayed on the DLB-A01N with that of the moisture analyzer.

If the two values do not match, read off the value at the temperature calibration

set and enter with the help of and confirm by .

9. When an optional printer is connected, an adjustment log can be edited.

10.Press to return into menu / start display.

DLB_A01N-BA-e-2011 7

3 DLB 160-3

Invoke service function:

In weighing mode press the MENU button and keep it pressed until the acoustic

signal gets mute. Release the button and the menu item “units“ will appear.

Press repeatedly the MENU button until „Service“ will be displayed.

Confirm by pressing the PRINT button. Select the required settings by pressing

the MENU button

Calibration of temperature, see chap. 3.1



Adjustment of temperature, see chap. 3.2



Settings of lamp

8 DLB_A01N-BA-e-2011

3.1 Calibration of temperature value

During temperature calibration only a check is carried out, i.e. no values are changed.

Invoke service function „Tmp test“, see chap. 3

Confirm by pressing the PRINT button. The current setting will be displayed. Use

the navigation buttons to select the temperature during the check, available

35- 160°C, e.g. 120°C.

Confirm using the PRINT button, the appliance heats up to the set temperature.

After approx. 15 minutes compare the test temperature with the displayed

temperature of the DLB-A01N. If the two values do not match, we recommend a

temperature adjustment, see chap. 3.2

Use the ON/OFF button to finish the calibration.

Use the ON/OFF button to return into weighing mode.

DLB_A01N-BA-e-2011 9

3.2 Adjustment of temperature value

The temperature is measured at two selectable points and it is possible to correct it

there.

Invoke service function „Tmp Adj“, see chap. 3

Confirm by pressing the PRINT button. The current setting for the first

temperature point is displayed. Or leave it on factory setting 80°C or select a

desired temperature with the help of the navigation buttons (available 50-

130°C).

Confirm with the PRINT button, the first heat-up phase is started. The remaining

time is displayed.

Temperature calibration for the first point takes 15 min. Compare the temperature

displayed on the DLB-A01N with that of the moisture analyzer. If the two values

do not match, correct them using the navigation buttons and confirm with the

PRINT button

The current setting for the second temperature point is displayed. Or leave it on

factory setting 150°C or select the desired temperature with the help of the

navigation buttons . The second temperature point has to be at least 30°C

over the first one, max. 160°C.

Confirm with the PRINT button, the second heat-up phase is started. The

remaining time is displayed.

Temperature calibration for the second point takes 15 min. Compare the

temperature displayed on the DLB-A01N with that of the moisture analyzer. If the

two values do not match, correct with the help of the navigation buttons .

Confirm by pressing the PRINT button. The adjustment is completed, the

appliance returns into the menu. Use the ON/OFF button to return into weighing

mode.

Tabla de contenidos

Otros manuales de Instrumento de medición de KERN

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario