Kemppi FASTMIG MS 200 Manual de usuario
FastMig
MS 200, MS 300
1903500
1515
OPERATING MANUAL
English
FastMig MS 200, MS 300
2
EN
CONTENTS
1. Preface........................................................................................................... 3
1.1 General ....................................................................................................................................... 3
2. Use.................................................................................................................. 4
2.1 Connecting and mounting the panels........................................................................... 4
2.2 Functions of MS 200 and MS 300 panels....................................................................... 5
2.3 MS 200 and MS 300 operations ........................................................................................ 6
2.4 Additional welding functions............................................................................................ 9
2.5 FastMig welding programs...............................................................................................11
2.6 Panel MS 200 and MS 300 setup parameters.............................................................14
3. FastMig error codes.................................................................................. 18
4. Disposal....................................................................................................... 19
5. Ordering numbers.................................................................................... 19
3
© Kemppi Oy / R03
EN
1. PREFACE
1.1 General
Congratulations on choosing the MS panel. Used correctly, Kemppi products can signicantly
increase the productivity of your welding, and provide years of economical service.
This operating manual contains important information on the use, maintenance and safety of
your Kemppi product. The technical specications of the equipment can be found at the end
of the manual.
Please read the manual carefully before using the equipment for the rst time. For your
own safety and that of your working environment, pay particular attention to the safety
instructions in the manual.
For more information on Kemppi products, contact Kemppi Oy, consult an authorised Kemppi
dealer, or visit the Kemppi web site at www.kemppi.com.
The specications presented in this manual are subject to change without prior notice.
Important notes
Items in the manual that require particular attention in order to minimise damage and
personal harm are indicated with the ’NOTE!’ notation. Read these sections carefully and follow
their instructions.
Disclaimer
While every eort has been made to ensure that the information contained in this guide
is accurate and complete, no liability can be accepted for any errors or omissions. Kemppi
reserves the right to change the specication of the product described at any time without
prior notice. Do not copy, record, reproduce or transmit the contents of this guide without
prior permission from Kemppi.
FastMig MS 200, MS 300
4
EN
2. USE
FastMig MS 200 and MS 300 control panels are designed to be used only with synergic power
sources FastMig M 320, 420, or 520. MS 200 panel can be mounted to MXF 63 (200 mm wire
spool) wire feeder and MS 300 panel to MXF 65 and 67 (300 mm wire spool) wire feeders.
2.1 Connecting and mounting the panels
Fasten the ribbon cable connector from the MXF wire feed unit to the function panel.
MXF 65
1.
2.
1. Place the bottom edge of the panel behind the securing clips on the machine. Remove
the xing pin from the top edge with, for example, a screwdriver. Then gently push
the upper part of the panel into place. Make sure that the cables do not get damaged,
continue gently pushing the upper part of the panel until it clips into place.
2. Finally secure the panel into place with the additional black plastic security clip provided
(MXF 65 only). Ensure that the clip is positioned correctly. You will notice that the clip
does not seat snuggly if it's positioned upside down.
MXF 63 + MXF 67
MXF 63 MXF 67
+
5
© Kemppi Oy / R03
EN
2.2 Functions of MS 200 and MS 300 panels
1. 2.
9. 10. 11. 12.
4.
5.
6.
8.
7.
3.
13.
14.
1. ON/OFF button
2. Memory channels for welding parameters (short press selects, long press saves)
3. a) Wire feed speed/welding current/sheet thickness display
b) Selected SETUP entry display
4. a) Adjustment of wire feed speed
b) Adjustment of welding power setting 1-MIG/WiseRoot/WiseThin **
c) Adjustment of MMA current
d) Selection of SETUP parameter
e) Selection of 1-MIG/WiseRoot/WiseThin welding program (material group) **
5. a) Selection of switching logic: 2T/4T/4T Minilog *
b) Long press: Setting the basic parameters (SETUP)
6. a) 1-MIG/WISE synergic welding program check **
b) 1-MIG/WISE synergic welding program selection (long press) **
7. a) Welding voltage display
b) Adjustable parameters display
8. a) Welding voltage adjustment
b) Adjustment of length of welding arc (1-MIG)
c) Adjustment of MIG dynamics
d) Adjustment of SETUP parameter
e) Selection of 1-MIG/WiseRoot/WiseThin welding program (program number) **
f) WiseRoot and WiseThin base current adjustment **
9. Selection LED indicators for synergic welding program – indicators for material, wire
thickness and gas type
10. Selection of MIG/1-MIG/MMA welding process
11. a) Selection of additional MIG functions
b) Weld data: Show last used welding parameters in displays (long press)
12. Manual control/remote control unit selection (long press for channel remote usage)
13. MIG dynamics/MMA Arc Force/Wise Forming Pulse selection **
14. Display of air/liquid cooled MIG gun (selection from setup)
*) Minilog is not included in standard delivery.
**) Wise products are available as optional welding process solutions. Not included in the
standard delivery. Please visit www.kemppi.com or Kemppi Datastore.
NOTE! With MS 200 and MS 300 panels ‘Wire Inch’ and ‘Gas Test’ buttons should be used from the
inside of the wire feed unit.
FastMig MS 200, MS 300
6
EN
2.3 MS 200 and MS 300 operations
ON/OFF button (1)
The wire feed unit remains in the OFF position when the power source is switched on, thus
preventing start-up. ’OFF’is shown on the display.
When the ON/OFF button is pressed for more than 1 second, the unit starts up. The unit is now
ready for welding and will automatically return back to it previous position, before the power
was cut o. The wire feed unit starts up also by pressing three (short) times the switch of the
welding gun.
Basic settings and displays
With MIG welding the wire feed speed is set via left potentiometer (control knob) and the
value is shown on the left display. The welding voltage is set via right potentiometer (control
knob) and the value is shown on the right display. During welding, the left display shows the
actual welding current value and the display on the right shows the welding voltage.
With electrode welding (MMA) the welding current value is set via the potentiometer and
the value is shown on the left display. The display on the right shows the idling voltage of the
power source. During welding the left display shows the actual welding current value and the
display on the right shows the welding voltage.
When MIG dynamics/electrode welding Arc force adjustment is activated with Arc Force/
Dynamics button the value is adjusted via right potentiometer (control knob) (see the
information on adjustment of MIG dynamics/arc force).
With Synergic 1-MIG welding, the power value is set via left potentiometer (control knob) and
the length of the arc via right potentiometer (control knob) (see ’1-MIG welding’).
Adjustment of MIG dynamics/Arc Force (13)
With MIG welding dynamics adjustment is inuenced on welding stability and spatter
amount. Zero setting is recommended basic setting. Values –> min (-1 ... -9), softer arc for
reduced spatter amount. Values –> max (1 ... 9), harder arc for increased stability and when
100 % CO₂ shielding gas is used when welding steel.
With electrode welding Arc Force adjustment is inuenced on welding stability. Adjustment
is needed for using dierent types of electrodes. Control range (-9 ... 0) is commonly used
for welding electrodes for stainless steel. Control range (0 ... +9) is used for harder arc
characteristic to increase stability, e.g. for welding with thicker basic electrodes and using
lower current value than recommendated. Factory set value (0) is a good general use for
adjusting the roughness of the arc.
Indication of liquid-cooled MIG gun (14)
You can activate either air or liquid cooled MIG gun with a setup parameter. For more
information, see chapter 2.6.
If the LED (14) is lit, liquid-cooling is activated in the system. In this case, ensure that you have
connected a liquid-cooled MIG gun to the equipment. The cooling units starts on the next
machine startup.
7
© Kemppi Oy / R03
EN
Weld data (11)
The weld data function is activated by long-pressing the additional welding functions button.
The weld data function returns the welding current and voltage values to the displays that
were in use during the last weld.
Selection of welding process (10)
The welding process – normal MIG or 1-MIG – can be chosen with the welding process
selection button. In normal MIG welding wire feed speed and welding voltage is adjusted
separately. In synergic 1-MIG and Wise welding the welding voltage and other parametres
related to welding are optimally bound to each other! In synergic welding the setting for
power and arc lenght are adjusted.
Electrode welding (MMA) is selected by pressing the button for >1 second. When electrode
welding is selected, the power source, the electrode holder connected to it and the MIG gun
become energised (open circuit voltage).
LED indicators: MMA (MMA selected), MIG (MIG selected), 1-MIG (1-MIG selected), 1-MIG +
WISE (1-MIG and either WiseFusion or WisePenetration selected , selection between the two is
done through SETUP) and WISE (WiseRoot or WiseThin selected, selection between the two is
done through welding program selection).
WiseRoot/WiseThin program is activated by choosing a WiseRoot/WiseThin welding program
(WISE led then turns on). Wise welding is the facility provided separately, so the function is
not in every equipment. WiseRoot and WiseThin require licences, which can be purchased in
Kemppi DataStore.
Selection of MIG operating procedure (5)
MIG 2T: MIG welding with two-sequence procedure of welding gun start switch
1. switch pressed: welding starts
2. switch released: welding stops
MIG 4T: MIG welding with four-sequence procedure of welding gun start switch
1. switch pressed: shielding gas ow starts
2. switch released: welding starts
3. switch pressed: welding stops
4. switch released: shielding gas ow stops
Minilog: Minilog is an additional function, which can be purchased separately. (Minilog is also
referred as 'Matchlog' in DataStore.)
Without Minilog license, press of the button chooses between 2T and 4T.
FastMig MS 200, MS 300
8
EN
Setup (5)
When the adjustment of SETUP parameters has been conrmed with a long press of the
SETUP button (10), the adjustable parameter is selected via left potentiometer (control knob)
and the name of the parameter is shown on the left display. The parameter’s value is set via
right potentiometer (control knob) and the value is shown on the display on the right (see
’SETUP functions’).
Synergic 1-MIG or Wise welding (6, 10)
In Synergic 1-MIG welding, the optimal welding parameters for the welding wires and gas
used are recorded in the unit. The welding is controlled by adjusting the welding power and
arc length.
Wise processes are additional functions, which can be purchased separately.
Welding program selection:
Before starting to weld, a welding program suitable for the welding wire and gas used must
be chosen based on this Operating Manual.
Welding program selection is activated by pressing Set Prog button longer than one second.
In this case both displays begin to ash and the material group is selected with the control
knob on the left and the welding program for the material group in question with the control
knob on the right.
First ve material groups are for Synergic 1-MIG welding and last ve are for Wise processes.
Refer to the selection LED indicators on the panel for synergic welding program – indicators
show the material, the wire thickness and the gas type in question.
The selected programme is immediately recorded in the memory. To get back to normal status
press ON/OFF (1) key, or Set Prog button (6).
Use of a selected welding program:
The selected welding program is immediately ready for welding. Check that the welding
program corresponds to the welding wire and shield gas in use. The selection LED indicators
on the panel show the material, the wire thickness and the gas type in use. The welding
program number can be checked by briey pressing the Set Prog button (6), after which the
displays show the welding program number.
TIP! The selected welding program can be saved for later use using one of the memory channels.
Refer to 'Memory functions'.
Set the desired welding power via the left-hand potentiometer (control knob) and the arc
length via the potentiometer (control knob) on the right.
Memory functions (2)
Storage of settings
The memory functions can be used to record useful welding values in the memory. There are
ve dierent memory channels under ve separate memory buttons: 1 … 5.
In addition to welding values (wire feed speed, welding voltage), function options such as
2T/4T, Creep Start, and Crater Level are recorded in the memory as well as the used welding
program.
Short press selects the memory locations.
Long press saves the current settings to the selected memory location.
Otros manuales para FASTMIG MS 200
1
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Sistema de soldadura de Kemppi
Kemppi
Kemppi A7 350 Guía de configuración rápida
Kemppi
Kemppi PRO EVOLUTION MXE Manual de usuario
Kemppi
Kemppi MasterTig 2200 Manual de usuario
Kemppi
Kemppi KEMPACT 251R Manual de usuario
Kemppi
Kemppi FastMig MXP 37 Pipe Steel Manual de usuario
Kemppi
Kemppi KempGouge ARC 800 Manual de usuario
Kemppi
Kemppi Promig 520R Manual de usuario
Kemppi
Kemppi FastMig X 450 Manual de usuario
Kemppi
Kemppi ArcFeed 200 Manual de usuario
Kemppi
Kemppi FitWeld Evo 300 Manual de usuario
Kemppi
Kemppi HiArc M 350A Manual de usuario
Kemppi
Kemppi FastMig MF 29 Manual de usuario
Kemppi
Kemppi Evo 150, 150VRD Manual de usuario
Kemppi
Kemppi Kempotig 4500 AC/DC Manual de usuario
Kemppi
Kemppi Master M 205 Manual de usuario
Kemppi
Kemppi MF 33 Manual de usuario
Kemppi
Kemppi MasterMig 353 Manual de usuario
Kemppi
Kemppi KEMPOWELD 4200 Manual de usuario
Kemppi
Kemppi MinarcTig Evo 200 Manual de usuario
Kemppi
Kemppi fastmig kms 400 mvu Manual de usuario
Manuales populares de Sistema de soldadura de otras marcas
TAFA
TAFA 30*8B35 Manual de usuario
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manual de usuario
ESAB
ESAB Buddy Arc 145 Manual de usuario
CIGWELD
CIGWELD 636804 Guía rápida
Red-D-Arc
Red-D-Arc DC-400 Manual de usuario
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario
