Kane 3200 Manual de usuario

KANE3200

Differential Pressure Meter

Stock No. 18950 November 2011

OVERVIEW

+/-200 mbar range

8 user selectable scales

Temperature compensated

One button zeroing

Long battery life

Robust case with integrally moulded protective boot

Integral magnets for hands-free operation

GENERAL OPERATION

The meter is controlled using 2 buttons.

The two buttons have dual functions as follows:

ON / OFF

To switch ON press and hold for 2 seconds until 3200 appears on the

display.

(During this 2 seconds all the segments of the display will be actuated.)

The display will then show the following sequence

1.0 the firmware version

HPA the units currently set

ZERO the zeroing sequence

00.0 the measured value

the meter is now ready for use.

To switch OFF press and hold until OFF appears on the display. (During this

period the meter will display the units currently set).

ZERO

Press and hold until ZERO appears on the display. The meter will then do a

zero countdown for a count of 4.

CHANGE UNITS

Quickly press and release .

The display will show the units currently set eg HPA.

Now press to scroll through the selection of units available.

When the units of choice are displayed, press to select.

1. BEFORE USING THE METER FOR THE FIRST TIME:

Remove the cover and fit a new battery in the battery compartment. Take great care

to ensure that the battery is fitted with the correct battery polarity. Then replace

the battery cover. Always check that the meter is working correctly after replacing

the battery.

2. BEFORE USING THE METER EVERY TIME:

After switch on, check that the battery power is sufficient and the displayed units are

the ones required.

SAFETY WARNING

Never connect to a pressure source where you are not sure what the maximum

pressure might be. Always ensuer that the meter you are using is correctly rated for

the pressure that you intend to measure. Excessive pressure (>5 times nominal

range) can permanently damage the meter’s pressure sensor.

NOTE: Use the

input for all single input measurement soft pressure or vacuum

Only use the

–

input when taking a differential measurement.

3. UNIT OPTIONS

PS UNITS

User selectable units are mBAR, inH20, hPa, mmHg, PSI, kPa, Pa, mmH2O

These are displayed as follows:

kPa

PSI

mmHg

hPa

inH2O

mBar

mmH2O

4. MEASURING

Make sure you do not exceed the meter’s operating specifications.

Do not exceed the meter’s internal temperature operating range

Do not put the meter on a hot surface

When taking critical draft measurements always re-zero the meter in the position you

are taking the readings and hold the meter still during the test.

Differential Port Port 1

IR Printer Output

Always use the top right hand port (Port 1) for taking single channel

measurements (pressure or vacuum). Only use the left hand port for differential

measurements.

If the pressure being measured exceeds the meter’s design range the display will

show ---- for “over-range”.

When taking draft readings at very low pressure or draft levels, for maximum

accuracy, re-zero the meter in the orientation that it is being used. This eliminated

gravity effects on the very sensitive pressure transducer. It is also recommended

that the meter is switched on for at least five minutes and then re-zeroed before

taking such sensitive measurements.

5. METER ANNUAL RECALIBRATION AND SERVICE

The meter should be re-calibrated and serviced annually by a Kane approved service

centre.

Local regulations may require more frequent re-calibration.

Calibration is performed in firmware and there are no user accessible adjustments or

user serviceable parts.

6. SPECIFICATION

Scale Range Highest Resolution

Mbar

200 0.01

9999 1

hPa

200 0.01

kPa

20 0.001

PSI

3.0 0.001

mm Hg

150 0.01

mm Wg

2100 0.01

In Wg

80 0.01

NOTE: The nominal range is plus and minus 200 mbar. The meter does not auto-

range and so when Pa units are selected the full operating range cannot be

displayed and the user must select an alternative range for measurements above

999 Pa.

ACCURACY:

0.5 mbar or

0.5% of reading whichever is greater. Maximum over-

range without damaging the sensor is 1000 mbar.

BATTERY LIFE: Greater than 250 hours continuous operation with a 9 V PP3

alkaline battery.

AMBIENT TEMPERATURE RANGE: 0

C to

AMBIENT HUMIDITY: 10% RH to 90% RH non-condensing

DIMENSIONS:

Weight: 295 grams with battery

Handset: 160mm x 80mm x 40mm (180mm including spigots)

Ambient Operating Range:

C to

C 10% to 90% RH non-condensing

Power Supply: 9 Volt PP3 alkaline battery

7. ELECTROMAGNETIC COMPATIBILITY

European Council Directive 89/336/EEC requires electronic equipment not to

generate electromagnetic disturbances exceeding defined levels and have adequate

immunity levels for normal operation. Specific standards applicable to this meter are

stated below.

As there are electrical products in use pre-dating this Directive, they may emit excess

electromagnetic radiation levels and, occasionally, it may be appropriate to check the

meter before use by:

Use the normal start up sequence in the location where the meter will be used.

Switch on all localized electrical equipment capable of causing interference.

Check all reading are as expected. A level of disturbance is acceptable.

If not acceptable, adjust the meter’s position to minimize interference or switch off, if

possible, the offending equipment during your test.

At the time of writing this manual (November 2011) Kane International Ltd are not

aware of any field based situation where such interference has occurred and this

advice is only given to satisfy the requirements of the Directive.

This product has been tested for

compliance with the following generic

standards:

EN 61000-6-3 : 2001

EN 61000-6-1 : 2001

and is certified to be compliant

Specification EC/EMC/KI/K455 details

the specific test configuration,

performance and conditions of use.

Please Note:

Batteries used in this instrument should be disposed of in accordance with current

legislation and local guidelines.

At the end of its life the meter should be sent to the appropriate recycling centre in

accordance with current legislation and local guidelines.

Thank you for buying this

Differential Pressure Meter.

Before use, please register

on our website

www.kane.co.uk

Tabla de contenidos

Otros manuales de Instrumento de medición de Kane

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario