Kaba Simplex 7104 Series Manual de usuario
Features
Access Control
Mechanical pushbutton lock eliminates problems and costs
associated with issuing, controlling, and collecting keys and cards.
Provides fully mechanical primary or auxiliary pushbutton access
control by exterior combination, while allowing free egress at all
times by interior thumbturn. Deadbolt models must be manually
relocked. Deadlocking latch models automatically relock each time
the door closes.
No Battery
Fully mechanical lock eliminates the material and labor expense
of battery replacements
Locking Device
Deadbolt—must be manually relocked
Deadlocking latch—relocks automatically when door closes
Rim locking latch—relocks automatically when door closes; also
has latch holdback
Number of Codes
Single access code—one easy-to-manage code for all users
Programming
Lock is easily programmed via keypad without removing lock from
the door
Handing
Field reversible
Operation Modes
Pushbutton Access
Latch Holdback (7106 only)
Economical
A cost eective access control solution
Simplex
®
7100
•1"(25mm)Tubular
Deadbolt,FlatFacePlate
•Backset2¾"(70mm)
•AuxiliaryLock
•ManualRelock
•NumerousFinishes
Model 7102
•½"(13mm)
DeadlockingLatch,
FlatFacePlate
•Backset2⅜"–2¾"(60-70
mm)—Adjustable
•Primary/AuxiliaryLock
•AutomaticRelock
•NumerousFinishes
Model 7104
•⅝"(16mm)Rim
DeadlockingLatch,Flat
FacePlate
•Backset2⅜"(60mm)
•ForWoodDoorsOnly
•AuxiliaryLock
•AutomaticRelockand
LatchHoldback
•SelectFinishes
Model 7106
•1"(25mm)Tubular
Deadbolt,FlatFacePlate
•Backset2⅜"(60mm)
•AuxiliaryLock
•ManualRelock
•NumerousFinishes
Model 7108
Kaba Access & Data Systems Americas
Winston-Salem NC 27105
1-800-849-8324
www.kaba-adsamericas.com KAA1356 0416
Mechanical Features
Construction All metal cast front housing; force-resistant, clutch-protected exterior thumbturn
Numeric Keypad Vandal resistant, solid metal pushbuttons
Door Handing Field reversible
Finishes
For all models except 7106: Bright Brass 03 (605), Satin Chrome 26D (626),
Antique Copper (AC) (059), Gold Vein (GV) (060), Antique White (AW) (062),
Silver Vein (SV) (061), Black 19 (676), and Antique Brass 05 (609)
Model 7106: Inside trim (Black only)
All other Black models, inside trim (Satin Chrome)
Latch
1" (25 mm) tubular deadbolt
½" (13 mm) deadlocking latch
⅝" (16 mm) rim deadlocking latch
Strike
Models 7102 and 7108: Flat deadbolt strike plate
Model 7104: Curved lip strike plate
Model 7106: Box strike for in-swing doors and at strike for out-swing doors
Minimum Stile Recommended
4" (102 mm)
Weight 2.5 lbs. (1.1 kg)
Installation
Installation 1⅜" (35 mm) diameter through bore; 1" (25 mm) diameter cross bore; ¾" (19 mm)
through bore; 2 x ¼" through bores
Backset 2¾" (70 mm) or 2⅜" (60 mm) backset
Door Thickness 1⅜" (35 mm) to 2¼" (57 mm), wood or metal
Items Supplied Include Installation manual, full-scale template and required installation hardware
Certication and Testing
Durability Weather resistant
Warranty
Warranty 1-year warranty
Exterior
6½"
(165 mm)
2½"
(64 mm)
Exterior Side
2½"
(64 mm)
6½"
(165 mm)
Interior
Models 7102, 7104, 7108
2"
(51 mm)
3⅝"
(92 mm)
2¼"
(57 mm)
Model 7106
3"
(76 mm)
3⅜"
(86 mm)
2⅛"
(54 mm)
1⅜"
(35 mm)
Latch
2¾"
(70 mm)
⅞"
(22 mm)
Changing the Code/Combination
Simplex 7000/7100
7000/7100 Series FAQ
Changing the Code/Combination
Note: If your lock is opening on every turn of the knob or lever, except upon entering a code, this may
be a ZERO CODE. Before attempting to remove the lock from the door, refer to the troubleshooting
procedures outlined at bottom of this document for a zero code symptom/solution.
Important: The following steps must be performed while the door is be
open.
The factory pre-set combination is 2 and 4 pressed simultaneously and re-
leased, then press 3 and release.
Read the instructions through once before attempting to change
the combination.
1. Turn the outside thumbturn to the left (counterclockwise) until it stops
then return it to the right (clockwise) slowly to the horizontal position
and release.
2. Enter the existing combination.
3. Insert a Phillips-head screwdriver into the central piece of the combina-
tion change assembly (see gure 1). Gently turn the screwdriver to the
right (clockwise) until it stops. A slight click should be felt. Do not force.
4. Remove the screwdriver from the combination change assembly.
Important: When removing the screwdriver, the central piece must return to its
initial position, if not, set it back to its original position using the screwdriver
(see Figure 1). If the central piece of the combination change assembly does not
return to its original position, the combination will be cancelled and the lock will
jam.
5. Turn the outside thumbturn to the left (counterclockwise) until it stops
and return it slowly to the right (clockwise) to the horizontal position
and release.
This clears the existing code (see gure 2).
6. Select a new combination and write it down. Some or all of the buttons
may be used for your new code, pressed individually or simultaneously.
Each button may be used only once. We do not recommend the use of a
one-button combination.
KAA1158 0108
7. With the door open, enter your new combination. Depress each button fully and release
it. You must feel a click each time you press a button to know that the button was
fully depressed.
8. Turn the outside thumbturn to the right (clockwise) until it stops; the latch/bolt
should retract.
9. For automatic relocking latches, release the outside thumbturn and the latch should return
to its initial extended position.
For manual relocking deadbolts, turn the outside thumbturn to the left (counterclockwise)
until it stops; the bolt should extend.
Keep the door open and test the operation of the lock 2–3 times to make sure your combination was
set correctly.
Note:
• Donotuseexcessiveforceatanytime.
• Ifawrongcombinationisenteredwhileoperatingthelock,turntheoutsidethumbturntothe
left (counterclockwise) to the top position and release (see Figure 2). This will clear any
previously depressed buttons. Enter in the correct combination.
Troubleshooting
Symptom/problem: Turning outside thumbturn clockwise always retracts latch without depressing
any buttons.
Cause: Lock is in zero combination.
Solution: Follow the procedure for setting a new combination except omit step 2.
Otros manuales para Simplex 7104 Series
3
Este manual sirve para los siguientes modelos
3
Otros manuales de Cerrar de Kaba
Kaba
Kaba Saflok QuantumII MT RFID Manual de usuario
Kaba
Kaba E-Plex 5000 Manual de usuario
Kaba
Kaba Simplex 506 Series Manual de usuario
Kaba
Kaba simplex 7106 series Manual de usuario
Kaba
Kaba Simplex Mechanical Pushbutton Locks Manual de usuario
Kaba
Kaba E-Flash EF680 Manual de usuario
Kaba
Kaba SIMPLEX 900 Series Manual de usuario
Kaba
Kaba Simplex 6200 Series Manual de usuario
Kaba
Kaba 7006 Series Manual de usuario
Kaba
Kaba PowerPlex 2000 Series Manual de usuario
Kaba
Kaba LA GARD 1947 Manual de usuario
Kaba
Kaba 1546-K5 Manual de usuario
Kaba
Kaba E-PLEX 2000 Manual de usuario
Kaba
Kaba E-730 Series Manual de usuario
Kaba
Kaba 1435MID Manual de usuario
Kaba
Kaba 5402 Series Manual de usuario
Kaba
Kaba SIMPLEX L1000 Series Manual de usuario
Kaba
Kaba 7102 series Manual de usuario
Kaba
Kaba Quantum Series Manual de usuario
Kaba
Kaba SIMPLEX LD450 Manual de usuario
