Küppersbusch IGV 699 Manual de usuario

   

 

 

 

en Index

Safety instructions 4. . . . . . . . . . . . .

Getting to know your appliance 6. .

Before using your appliance

for the first time 7. . . . . . . . . . . . . . . .

Filling in the Salt 8. . . . . . . . . . . . . . .

Setting up the water softener 9. . . .

Filling with rinse aid 10. . . . . . . . . . . .

Unsuitable dishes 11. . . . . . . . . . . . .

Arranging crockery, glasses,

etc. in the dishwasher 12. . . . . . . . . .

Detergents 15. . . . . . . . . . . . . . . . . . .

Opening and closing the door 17. . .

serve@Home * 18. . . . . . . . . . . . . . . .

Adjusting the appliance 19. . . . . . . . .

auto 3in1 19. . . . . . . . . . . . . . . . . . . . .

Programme overview 21. . . . . . . . . .

Selecting options/standard settings 22

Maintenance and care 28. . . . . . . . . .

Fault finding 30. . . . . . . . . . . . . . . . . .

Customer Service 33. . . . . . . . . . . . .

Notes 33. . . . . . . . . . . . . . . . . . . . . . . .

Installation 34. . . . . . . . . . . . . . . . . . . .

Safety instructions

Delivery

Immediately check the packaging and

dishwasher for any damage which may

have been caused in transit. Do not use

a damaged appliance, but consult your

supplier.

Please dispose of packaging material

properly.

The corrugated cardboard consists

mainly of waste paper.

The polystyrene moulded parts have

been foamed without any CFCs.

The polyethylene film (PE) consists

partly of secondary raw material.

The wooden frames (if fitted) are made

of residual wood and are untreated.

The hoops (if fitted) consist of

polypropylene (PP).

Installation

Install and connect the appliance

according to the installation and

assembly instructions.

The dishwasher must NOT be

connected to the power supply during

installation.

Ensure that the protective conductor

system of the domestic electricity

supply has been installed correctly.

Electrical connection conditions must

correspond with the specifications on

the rating plate of the dishwasher.

In order for your dishwasher to become

serve@Home capable, you will need

a special accessory, the System

Interface (available from your specialist

supplier). Please follow the enclosed

installation instructions, and install the

system interface in the chamber located

at the front of the dishwasher.

Built-under and built-in appliances

should always be installed under a

continuous work surface which is

attached to the adjacent cupboards, in

order to ensure that the appliance is

entirely stable.

After the appliance has been installed,

the mains plug should still be easily

accessible.

Not on all models:

The plastic housing on the water input

contains an electrically operated valve.

The connecting wires are inside the

inlet hose. Do not cut through this hose

and do not immerse the plastic housing

in water.

Warning

For safety reasons, if the appliance is not

fitted in a recess, thereby making a side

wall accessible, the door hinge area

should be covered at the side.

(Risk of injury)

Covers are available as optional

accessories from customer services or

specialist stores.

In daily use

Warning

Knives and other utensils with sharp points

must be placed in the baskets either flat or

with the points downwards.

Use the dishwasher only in the

household and only for its designed

purpose, i.e. for washing domestic

dishes.

Do not lean or sit on the open door.

The appliance could tip.

The water in the appliance is not

drinking water.

Do not add any solvents to the washing

chamber. Danger of explosion!

Open the door carefully when the

programme is still running. Water could

spray out of the appliance.

Read and observe the safety

information and instructions for use on

the packaging for cleaning and rinsing

agents.

Children in the household

Do not let infants play or operate the

dishwasher.

Keep cleaning and rinsing agents out of

the reach of infants.

Keep infants away from the open

dishwasher. It could contain residue of

the cleaning agent.



To prevent injuries, e.g. caused by

stumbling, open the dishwasher only

briefly in order to load and unload the

dishwasher.

If a fault occurs

Repairs or other work on the

dishwasher should only be carried out

by a qualified specialist.

The dishwasher must be disconnected

from the electricity supply before any

repairs or other work are started. Pull

the mains plug out of the wall socket or

switch off at the fuse box. Grasp the

plug to remove it from the socket; do

not tug on the cable. Turn the water off

at the tap.

When disposing of old

appliances

Appliances that have reached the end

of their service life should be rendered

inoperable in order to exclude the

possibility of subsequent accidents. Pull

the mains plug out of the wall socket,

cut through the connecting cable and

disable the door lock.

Take the appliance to a designated

waste disposal centre.

Warning

Children could get locked in the appliance

(risk of suffocation) or get stuck in other

positions.

Therefore: Remove the mains plug, cut the

mains wire and set aside. Damage the

door lock so that the door can no longer

be closed.

Getting to know your

appliance

Diagrams of the control panel and the

interior of the appliance can be found

in the envelope at the front.

Individual positions are referred to in

the text.

Control panel

1 Main switch

2Button M/OK: Select options, store

(changed) value

3Buttons – and +: Select programmes

and settings

4This display gives optical character

information on the programmes,

options, and settings to be selected

as well as on the available actions.

5Start Button: Start programme

6Door Opener

The luminous arrows indicate whether you

are able to select among other options

using – or + 3.

This dishwasher is equipped with touch

buttons. A gentle touch starts the function.

Always keep the user interface clean

and free of grease in order to prevent

malfunctions. Use a dry or lightly

moistened cloth only, do not use

scouring or abrasive detergents.

Appliance interior

20 Upper utensils basket

21 Additional cutlery basket * for the

top basket

22 Additional cup rack *

23 Upper spray arm

24 Lower spray arm

25 Dispenser for salt

26 Filters

27 Cutlery basket

28 Lower utensils basket

29 Lock

30 Dispenser for rinse aid with refill

display

31 Detergent dispenser

32 Optical limescale sensor

33 Rating plate

* some models

Before using your appliance for the first time

Before you can use your appliance for the first time, you must select the language. When

the appliance has been switched on, the following display is output:

DE EN FR NL IT EL

M

OK 

–+

The language abbreviation “DE” for

“Deutsch” (German) is flashing. If you

want to select a different language,

press – or + 3repeatedly until the

abbreviation of your desired language

flashes.

Confirm the language selection by

pressing M/OK 2.

All following optical character messages

will be displayed in the selected language.

Chosen the wrong language

The following steps will take you back

to the language selection:

1. Switch off the device.

2. Switch on the device. Press the button

M/OK 2until the language selection

is displayed.

3. Select the desired language and

confirm your selection.

Providing operating materials

To operate the dishwasher you will require

salt (only for appropriate water

hardness, see chapter “Adjusting

the softening system”),

rinse aid,

detergent.

Only use products which are suitable

for the dishwasher.

Before using the appliance for the first time

and after selecting the language, fill with

salt (if required) and rinse aid and adjust

the softening system. Proceed as

described in the chapters “Filling with salt”,

“Filling with rinse aid” and “Adjusting the

softening system”.

Filling in the Salt

Note

If the hardness of your mains

water corresponds to the

device’s index value (see

chapter “Setting up the softening

system”), you do not need to fill

in the salt because the operation

will not use any salt. In case of

the settings “Hardness-Auto” and

to , salt must be filled in.

During the rinse cycle the salt is being

washed automatically from the salt

compartment into the softening system

where it will dissolve the lime.

The lime-containing solution drains from

the dishwasher. Afterwards the softening

system is ready to be loaded again.

This regeneration cycle will only work if

the salt is dissolved in water.

After switching on the device, lack of salt

is indicated by the display “Refill Salt”.

(This display will no longer appear once

you have set the softening system to the

value .)

Open the screw-type cap of the

compartment 25 .

Before operating the device for the first

time you must pour 1 litre of water into

the salt compartment.

Then you must refill salt (not table salt)

using the supplied salt filling aid until the

salt compartment is full (max 1.5 kg).

When you refill the salt, water is being

displaced and drains off. Therefore the

refilling must take place shortly before

switching on the device. (In order to avoid

corrosion). This way the overflowing salt

solution is diluted and flushed immediately.

Then clean the filling area of salt residues

and screw the compartment lid back on

without tilting the lid.

As soon as a sufficiently high salt solution

has formed the display “Refill Salt” will

disappear.

If you do not want to wait until the display

disappears but you want to wash

immediately, confirm the refilling of the salt

using the button M/OK 2.

If you do not want to refill the salt now you

can skip the display “Refill Salt” by

pressing the button M/OK 2.

Do not pour detergent into the

container for special salt. This

would destroy the water

softener.

Setting up the water

softener

In order to provide satisfactory rinsing

results, the dishwasher requires soft water,

i.e., containing little or no lime, otherwise

water stains will be left behind on the

dishes and interior containers.

If the tap water exceeds a certain level of

hardness, it must be softened, i.e.,

decalcified, so that it can be used in the

dishwasher.

This is achieved by adding a special salt

to the water softener inside the

dishwasher.

The water softener, that is the required

amount of salt, is set up according to how

hard the tap water is.

The softening system is only capable to

accept a limited amount of lime. If this

limit is reached the system must be

regenerated or refreshed using salt.

The factory setting “Hardness-Auto” allows

the deposit sensor to determine the

hardness and to control the softening

system automatically. This means that

changes to the settings are unnecessary

during start-up or in case of changes in

the water hardness.

If you would nevertheless like to set

the water softening system manually,

proceed as follows:

Find out the degree of hardness of your

tap water. Your water supply company

or customer service will assist you.

Switch on the appliance with the main

switch 1. The main menu is

displayed (if switching on the appliance

for the first time, only when a language

has been selected and dispensers

have been filled with salt (if required)

and rinse aid).

Press the button M/OK 2until

“Hardness-Auto” is displayed.

Using the buttons – or + 3, select the

setting corresponding to the hardness

of your mains water. The factory setting

is “Hardness-Auto”.

Press the button M/OK 2to store the

setting and return to the Main Menu.

If the setting is “0” the softening system is

switched off. Possible lack of salt will not

be indicated.

Filling with rinse aid

Rinse aid is used in washing mode to

ensure that glasses are sparkling and

utensils are stain-free.

When the appliance is switched on, low

rinse aid level is indicated by ”Refill rinse

aid”. You can add rinse aid either when the

appliance door is completely open or – for

a more comfortable posture – when the

door is half open.

Open the rinse aid dispenser 30 by

pressing the button on the dispenser

cover and open the cover. When the

door is half open, also pull out the

hinged filling aid until it locks into

position.

Fill in the rinse aid slowly and take care

not to overfill. The right amount is

indicated by the level indicator at the

compartment not being illuminated

when the door is fully opened and by

the display “Refill Rinse Aid” no longer

being lit.

Close the lid of the compartment until it

audibly clicks into place. If necessary,

the filling aid will be re-inserted

automatically.

If you want to fill in the rinse aid at a later

time you can skip the display “Refill Rinse

Aid” by pressing the button M/OK 2.

If necessary, you can change the amount

of rinse aid that is added during the

operation. In order to do this, select the

option “Rinse Aid Amount” as described

in the chapter “Device Set-up” under

the heading “Options/Basic Settings”.

rinse–aid control

Fill when door is fully open.

Filling when the door is half open.

Note

Use only rinse aid for domestic

dishwashers. Spilt rinse aid

may result in excessive foam

formation in the next rinse

cycle. Therefore, remove any

spilt rinse aid with a cloth.

Otros manuales para IGV 699

Tabla de contenidos

Otros manuales de Lavavajillas de Küppersbusch

Küppersbusch

Küppersbusch IGV 458.4 Manual de usuario

Küppersbusch

Küppersbusch IGV 668.0 Manual de usuario

Küppersbusch

Küppersbusch IGV 459 Series Manual de usuario

Küppersbusch

Küppersbusch IGV 689.1 Guía de configuración rápida

Küppersbusch

Küppersbusch IGV 445.0 Manual de usuario

Küppersbusch

Küppersbusch IGV 457.2 Manual de usuario

Küppersbusch

Küppersbusch Dishwasher Manual de usuario

Küppersbusch

Küppersbusch Dishwasher Manual de usuario

Küppersbusch

Küppersbusch IGV 6507.0 Manual de usuario

Küppersbusch

Küppersbusch IGV 655.1 Manual de usuario

Küppersbusch

Küppersbusch IGV4408 Manual de usuario

Küppersbusch

Küppersbusch Dishwasher Manual de usuario

Küppersbusch

Küppersbusch IGV 645.2 Manual de usuario

Küppersbusch

Küppersbusch IGV 649 Manual de usuario

Küppersbusch

Küppersbusch Dishwasher Manual de usuario

Küppersbusch

Küppersbusch IGV6509 Manual de usuario

Küppersbusch

Küppersbusch IGV 657.1 Manual de usuario

Küppersbusch

Küppersbusch IGV659.2 Manual de usuario

Küppersbusch

Küppersbusch IGV6504.0 Manual de usuario

Küppersbusch

Küppersbusch IGV 449.3 Manual de usuario

Küppersbusch

Küppersbusch IGVS6506 Manual de usuario

Küppersbusch

Küppersbusch IGV 699 Manual de usuario

Küppersbusch

Küppersbusch IGV 643.4 Manual de usuario

Küppersbusch

Küppersbusch IGV 656.1 Manual de usuario

Manuales populares de Lavavajillas de otras marcas

Electrolux

Electrolux ESI5211LOX Manual de usuario

KitchenAid

KitchenAid KUDB230B Manual de usuario

Brandt

Brandt BDJ424DB Manual de usuario

Asko

Asko DSD767UXXL.AU Manual de usuario

Beko

Beko DFN26210W Manual de usuario

NEFF

NEFF S153ITX00E Hoja de especificaciones

Midea

Midea SV 4.45 wi Manual de usuario

LG LDF7932 Manual de usuario

Gorenje

Gorenje GV63214 Manual de usuario

Hotpoint

Hotpoint HDA1100ZWH Manual de servicio

Blomberg

Blomberg LDFN2240W Manual de usuario

AEG

AEG FFB83836PM Manual de usuario

Cylinda

Cylinda DM3220RFD Manual de usuario

Atag

Atag DW8214MB Manual de usuario

GE GLD8000 Series Manual de usuario

Siemens

Siemens SN23HI02KE Hoja de especificaciones

Omega

Omega ODW717X Manual de usuario

BORETTI

BORETTI BVW-683 Manual de usuario