JYTEK PXIe-69529 Manual de usuario

PXIe-69529

8-CH 24-Bit 204.8 kS/s

Dynamic Signal Acquisition Module

User’s Manual

Manual Rev.: 1.00

Revision Date: Jul.16,2016

Getting Service

SHANGHAI JYTEK Co., Ltd.

Web site: hp://www.jytek.com

Address: 300 Fang Chun Rd., Zhangjiang Hi-Tech Park, Pudong New Area, Shanghai, 201203

China

Tel: +86-21-5047-5899

Fax: +86-21-5047-5899

Email: [email protected]

Addional informaon, aids, and ps that help users perform tasks

Informaon to prevent minor physical injury, component damage, data loss,

and/or program corrupon when trying to complete a task.

Informaon to prevent serious physical injury, component damage, data loss,and/

or program corrupon when trying to complete a specic task.

Table of Contents

Geng Service �� I

1 Introducon�� 1

1�1 Features �� 1

1.2 Applicaons �� 1

1.3 Specicaons �� 2

1�3�1 Analog Input �� 2

1�3�2 Timebase �� 4

1�3�3 Triggers �� 4

1.3.4 General Specicaons �� 4

1.4 Soware Support �� 5

1�4�1 SDK �� 5

1�4�2 DSA-DASK�� 5

1�5 Device Layout and I/O Array�� 6

2 Geng Started�� 8

2.1 Installaon Environment �� 8

2�2 Installing the Module �� 9

3 Operaons ��10

3.1 Funconal Block Diagram��10

3�2 Analog Input Channel��10

3.2.1 Analog Input Front-End Conguraon ��10

3�2�2 Input Range and Data Format��11

3�2�3 ADC and Analog Input Filter ��12

3�2�4 DMA Data Transfer��12

3�3 Trigger Source and Trigger Modes��14

3�4 Trigger Mode��16

3�5 ADC Timing Control ��18

3�5�1 Timebase ��18

3�5�2 DDS Timing vs� ADC��18

3�5�3 Filter Delay in ADC ��19

3.6 Synchronizing Mulple Modules ��19

3.6.1 SSI_TIMEBASE ��20

3�6�2 SSI_SYNC_START ��20

3�6�3 SSI_TRIG��20

Appendix A Calibraon ��21

A.1 Calibraon Constant ��21

A.2 Auto-Calibraon ��21

Important Safety Instrucons ��22

III

List of Tables

Table 1-1: Channel Characteriscs�� 2

Table 1-2: Timebase�� 4

Table 1-3: Trigger Source & Mode �� 4

Table 1-4: Digital Trigger Input �� 4

Table 3-1: Input Range and Data Format ��11

Table 3-2: Input Range Midscale Values ��12

Table 3-3: ADC Sample Rates vs DDS Output Clock��12

Table 3-4: Preferred Characteriscs for Analog Triggers��16

Table 3-5: Timing Relaonship between ADC and PLL Clock ��18

Table 3-6: ADC Filter Delay��19

Table 3-7: SSI Timing Signal Denions ��19

List of Figures

Figure 1-1: Analog Input Channel Bandwidth, ±0.2 Vpp �� 3

Figure 1-2: Analog Input Channel Bandwidth, ±2 Vpp �� 3

Figure 1-3: PXIe-69529 schemac �� 6

Figure 1-4: PXIe-69529 I/O Array�� 7

Figure 3-1: Analog Input Architecture ��10

Figure 3-2: Linked List of PCI Address DMA Descriptors��13

Figure 3-3: Trigger Architecture��14

Figure 3-4: External Digital Trigger ��14

Figure 3-5: Analog Trigger Condions ��16

Figure 3-6: Post-Trigger Acquision��17

Figure 3-7: Delay Trigger Mode Acquision��17

Figure 3-8: Re-Trigger Mode Acquision ��18

Figure 3-9: Timebase Architecture ��18

Figure 3-10: SSI Architecture��20

1 Introduction

The PXIe-69529 is a high-performance 8-CH 24-Bit 204.8 kS/s dynamic signal acquision

module, specically designed for applicaons such as structural health monitoring, noise,

vibraon, and harshness (NVH) measurement, and phased array data acquision.

The PXIe-69529 features 24-bit simultaneous sampling at 204.8 kS/s over 8 channels,

and a 110 dB dynamic range, providing ample power for high-density, high channel count

signal measurement, and vibraon-opmized lower AC cuto frequency of 0.3 Hz. All input

channels incorporate 4 mA bias current for integrated electronic piezoelectric (IEPE) signal

condioning for accelerometers and microphones.

The PXIe-69529 is auto-calibrated with an onboard reference circuit calibrang oset and

acquiring analog input errors. Following auto-calibraon, the calibraon constant is stored

in EEPROM, such that these values can be loaded and used as needed by the board. There

is no requirement to calibrate the module manually.

1�1 Features

• PXI Express specicaon Rev. 1.0 compliant

• 8 simultaneous analog inputs

• 204.8 kS/s maximum sampling rate

• AC or DC input coupling, soware selectable

• Support for:

◦ One external digital trigger input

◦ IEPE output on each analog input, soware congurable

◦ Auto-calibraon

1�2 Applications

• Structural health monitoring

• Phase array data acquision

• Noise, vibraon, and harshness (NVH) detecon

• Machine status monitoring

1�3 Specifications

1�3�1 Analog Input

Channel Characteriscs Comment

Channels 8

Type Dierenal or Pseudo-Dierenal

Coupling AC or DC, soware selectable

AC coupling cuto frequency 0.5Hz

ADC resoluon 24-Bit

ADC type Delta-sigma

Input signal range ±10V, ±1V

Sampling rate (fs) 8 kS/s to 204.8 kS/s,

768 μS/s increments for fs > 108 kS/s,

576 μS/s increments for 54 kS/s ≤ fs

≤108 kS/s

Over voltage protecon Dierenal: ±42.4V, Pseudo-

dierenal:

• posive terminal ±42.4 V

• negave terminal unprotected,

rated at ±2.5 V

Input impedance 1MΩ, (50Ω between negave input and

system ground for pseudo-dierenal

mode)

Oset error ±1 mV max.

Gain error ±0.1% of FSR

SNR, @n = 1kHz 103 dB fs = 8.0 kS

104 dB fs = 54.0 kS

99 dB fs = 108 kS

98 dB fs = 192 kS

THD < -106 dB

SFDR > 106 dB

crosstalk < -100 dB

-3 dB bandwidth >0.4863 fs fs < 108 kS

≌ 0.2 fs fs > 108 kS

IEPE

Current 4 mA, each channel independently

soware congurable

Compliance 24V

Table 1-1: Channel Characteriscs

0 1 2 3 4 5 6

x 10

−25

−20

−15

−10

−5

Magnitude Response

Frequency (Hz)

Magnitude (dB)

Figure 1-1: Analog Input Channel Bandwidth, ±0.2 Vpp

0 1 2 3 4 5 6 7 8 9 10

−12

−10

−8

−6

−4

−2

0Response when AC coupling enabled

Frequency (Hz)

Magnitude (dB)

Figure 1-2: Analog Input Channel Bandwidth, ±2 Vpp

1�3�2 Timebase

Sampling Clock

Timebase opons Internal: onboard synthesizer

External: PXI_CLK10, PXIe_CLK100

Timebase accuracy < ± 25ppm

Table 1-2: Timebase

1�3�3 Triggers

Trigger Source & Mode

Trigger source Soware, external digital trigger, analog trigger, PXI trigger

bus[0..7], PXI_STAR, and PXIe_DSTARB

Trigger mode Post trigger and delay trigger

Table 1-3: Trigger Source & Mode

Digital Trigger Input

Sources Front panel SMA connector

Compability 3.3 V TTL, 5 V tolerant

Input high threshold 2.0 V

Input low threshold (VIL) 0.8 V

Maximum input overload -0.5 V to +5.5 V

Trigger polarity Rising or falling edge

Pulse width 20 ns minimum

Table 1-4: Digital Trigger Input

1�3�4 General Specifications

Physical

Physical dimensions 160 W x 100 H mm (6.24 x 3.9 in)

Bus

Bus interface PCI Express Gen1 x 4

Environmental Tolerance

Operang Temperature: 0°C - 55°C

Relave humidity: 10% - 90%, non-condensing

Storage Temperature: -20°C - +80°C

Relave humidity: 10% - 90%, non-condensing

Calibraon

Onboard reference +5.000 V

Temperature coecient < 5.0 ppm/°C

Warm-up me 15 minutes

Tabla de contenidos

Otros manuales de Unidad de control de JYTEK

JYTEK

JYTEK PXI-67921 Manual de usuario

JYTEK

JYTEK JY5312 Manual de usuario

JYTEK

JYTEK PXI-67931 Manual de usuario

JYTEK

JYTEK PXI-93518 Manual de usuario

JYTEK

JYTEK USB-61900 Series Manual de usuario

JYTEK

JYTEK JY6302 Manual de usuario

JYTEK

JYTEK JY6301 Manual de usuario

JYTEK

JYTEK USB-61210 Manual de usuario

JYTEK

JYTEK PCIe-5211 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario