Jura IMPRESSA C50 Manual de usuario

IMPRESSA C50 – Quick Reference Guide

The ‘IMPRESSA C50 Instructions for Use’ together with these short

instructions ‘IMPRESSA C50 – Quick Reference Guide’ has been awarded

the seal of approval by the independent German Technical Inspection

Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness

and coverage of safety aspects.

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

These short instructions do not replace the ‘IMPRESSA C50 Instruc-

tions for Use’. Make sure you read and observe the safety informa-

tion and warnings first in order to avoid hazards.

You can initiate the rinse operation manually at any time.

Precondition: ESPRESSO is displayed (example).

TPlace a receptacle under the coffee spout.

OTTouch the P symbol for approximately 2 seconds until

RINSE appears on the display.

kTPress the Rotary Switch to enter the programme item.

RINSE

kTPress the Rotary Switch to initiate the rinse operation.

RINSING, water flows out of the coffee spout.

The rinse stops automatically. ESPRESSO appears on the

display (example).

EThis chapter applies to the professional fine foam frother

and the fine foam frother.

To ensure that the fine foam frother always works properly, you

must rinse it with water after every milk preparation.

Your IMPRESSA will not prompt you to rinse the fine foam frother.

Precondition: ESPRESSO is displayed (example).

TRemove the milk pipe from the milk container or carton.

TFill a receptacle with 250 ml of fresh water.

TImmerse the milk pipe in the receptacle.

TPlace a receptacle under the fine foam frother.

nTTouch the Steam symbol.

HEATING / STEAM

As soon as the machine has heated up, STEAM / READY

appears, the light segment on the switch lights up.

hTTurn the switch to the mposition.

STEAM appears and the fine foam frother and the milk

pipe are rinsed with fresh water.

Rinsing the machine

Rinsing the fine foam

frother

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

jTWhen clean water starts to flow out of the frother, turn the

switch back to the oposition.

STEAM / READY

The rinsing of the fine foam frother is now complete.

EThis chapter applies to the professional fine foam frother

and the fine foam frother.

To ensure that the fine foam frother always works properly, you

must clean it daily when you have been preparing milk. Your

IMPRESSA will not prompt you to clean the fine foam frother.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

EJURA Cappuccino Cleaner is available from specialised dealers.

Precondition: ESPRESSO is displayed (example).

TRemove the milk pipe from the milk container or carton.

TPour 250 ml of fresh water into a receptacle and add one

capful of Cappuccino Cleaner.

TImmerse the milk pipe in the receptacle.

TPlace a receptacle under the fine foam frother.

nTTouch the Steam symbol.

HEATING / STEAM

As soon as the machine has heated up, STEAM / READY

appears, the light segment on the switch lights up.

hTTurn the switch to the mposition.

STEAM appears and the fine foam frother and the milk

pipe are cleaned.

jTAs soon as the receptacle containing the cleaning solution is

empty, turn the switch to the oposition.

STEAM / READY

TRinse the receptacle thoroughly, fill it with 250 ml of fresh

water and immerse the milk pipe in the water.

TEmpty the other receptacle and place it under the fine foam

frother once more.

Cleaning the fine foam

frother

CAUTION

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

hTTurn the switch to the mposition.

STEAM, the fine foam frother and the milk pipe are rinsed

with fresh water.

jTAs soon as the receptacle containing the fresh water is

empty, turn the switch to the oposition.

STEAM / READY

The cleaning of the fine foam frother is now complete.

To make sure the fine foam frother works properly, and in the inter-

ests of hygiene, it must be dismantled and rinsed daily if you have

been preparing milk. Your IMPRESSA will not prompt you to disman-

tle and rinse the frother.

TRemove the milk pipe and rinse it thoroughly under running

water.

TCarefully remove the fine foam frother from the Connector

System©by twisting slightly.

TDismantle the fine foam frother into its individual parts.

TRinse all the parts of the fine foam frother thoroughly under

running water. If there are severely dried-on milk residues,

firstly immerse the individual parts in JURA Cappuccino

Cleaner and then rinse them thoroughly.

TRe-assemble the fine foam frother.

EEnsure that all individual parts are correctly and firmly con-

nected to ensure optimum operation.

TFirmly attach the fine foam frother to the Connector Sys-

tem©.

To make sure the professional fine foam frother works properly, and

in the interests of hygiene, it must be dismantled and rinsed daily if

you have been preparing milk. Your IMPRESSA will not prompt you

to dismantle and rinse the frother.

TRemove the milk pipe and rinse it thoroughly under running

water.

TCarefully remove the professional fine foam frother from the

Connector System©by twisting slightly.

Dismantling and rinsing

the fine foam frother

Dismantling and rinsing

the professional fine

foam frother

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

TDismantle the professional fine foam frother into its individ-

ual parts.

TRinse all the parts of the professional fine foam frother thor-

oughly under running water. If there are severely dried-on

milk residues, firstly immerse the individual parts in JURA

Cappuccino Cleaner and then rinse them thoroughly.

TRe-assemble the professional fine foam frother.

EEnsure that all individual parts are correctly and firmly con-

nected to ensure optimum operation.

TFirmly attach the professional fine foam frother to the Con-

nector System©.

Your IMPRESSA no longer has to be descaled if you are using the

CLARIS Blue filter cartridge. If you did not activate the filter cartridge

the first time you used the machine, you can do this now as follows.

EPerform the ‘inserting the filter’ operation without any inter-

ruptions. This will ensure that your IMPRESSA always produces

its best.

Precondition: ESPRESSO is displayed (example).

OTTouch the P symbol for approximately 2 seconds until

RINSE appears on the display.

gTTurn the Rotary Switch until FILTER- is displayed.

kTPress the Rotary Switch to enter the programme item.

gTTurn the Rotary Switch until YES is displayed.

kTPress the Rotary Switch to confirm the setting.

OK appears briefly on the display.

FILTER INSERT, the Maintenance symbol clights up.

TRemove and empty the water tank.

TOpen the filter holder.

TRemove the CLARIS Blue filter cartridge from the Welcome

Pack.

Inserting and activating

the filter

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

TInsert the CLARIS Blue filter cartridge into the water tank,

exerting slight pressure.

TClose the filter holder. It will click into place audibly.

EAfter two months, the filter will cease to work. Set the date on

the date plate on the filter holder in the water tank.

TFill the water tank with fresh, cold water and reinsert the

tank.

TPlace a receptacle (at least 500 ml) under the fine foam

frother.

cTTouch the Maintenance symbol.

SWITCH OPEN, the light segment on the switch lights up.

hTTurn the switch to the mposition.

FILTER RINSING, water flows out of the fine foam

frother.

EYou can interrupt rinsing of the filter at any time. To do this,

turn the switch clockwise. Turn the switch anticlockwise to

continue rinsing the filter.

EThe water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately

500 ml. SWITCH CLOSE appears on the display.

jTTurn the switch to the oposition.

HEATING, the machine heats up.

ESPRESSO appears on the display (example). The filter is

now activated.

EAfter 50 litres of water have flowed through, the filter will

cease to work. Your IMPRESSA will automatically prompt you

to change the filter.

EAfter two months, the filter will cease to work. Set the date on

the date plate on the filter holder in the water tank.

EIf the CLARIS Blue filter cartridge is not activated in program-

ming mode, you will not be prompted to change the filter.

ECLARIS filter cartridges are available from specialised dealers.

Changing the filter

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

Precondition: FILTER / ESPRESSO is displayed (example).

cTTouch the Maintenance symbol for approximately 2

seconds.

FILTER CHANGE appears on the display.

TRemove and empty the water tank.

TOpen the filter holder and remove the old CLARIS Blue filter

cartridge.

TInsert a new CLARIS filter cartridge Blue into the water tank,

exerting slight pressure.

TClose the filter holder. It will click into place audibly.

TFill the water tank with fresh, cold water and reinsert the

tank.

TPlace a receptacle (at least 500 ml) under the fine foam

frother.

cTTouch the Maintenance symbol.

SWITCH OPEN, the light segment on the switch lights up.

hTTurn the switch to the mposition.

FILTER RINSING, water flows out of the fine foam

frother.

EYou can interrupt rinsing of the filter at any time. To do this,

turn the switch clockwise. Turn the switch anticlockwise to

continue rinsing the filter.

EThe water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately

500 ml. SWITCH CLOSE appears on the display.

jTTurn the switch to the oposition.

HEATING, the machine heats up.

ESPRESSO appears on the display (example).

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

After 200 preparations or 80 switch-on rinses, the IMPRESSA will

prompt you to clean it.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

EThe cleaning programme lasts approximately 20 minutes.

EDo not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

EJURA cleaning tablets are available from specialised dealers.

Precondition: CLEAN / ESPRESSO is displayed (example).

cTTouch the Maintenance symbol for approximately 2

seconds.

EMPTY TRAY appears on the display.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

PRESS RINSE

TPlace a receptacle under the coffee spout.

cTTouch the Maintenance symbol.

CLEANING, water flows out of the coffee spout.

The operation is interrupted, ADD TABLET.

TOpen the cover of the filler funnel for ground coffee.

TInsert a JURA cleaning tablet into the filler funnel.

TClose the cover of the filler funnel.

cTTouch the Maintenance symbol.

CLEANING, water flows out of the coffee spout several

times.

The operation stops automatically.

EMPTY TRAY

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

HEATING

ESPRESSO appears on the display (example). Cleaning is

now complete. Your IMPRESSA is once more ready for use.

Cleaning the machine

CAUTION

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

The IMPRESSA builds up deposits of limescale over time and auto-

matically prompts you to descale it when necessary. The degree of

calcification depends on the hardness of your water.

If the descaling agent comes into contact with the skin or eyes, this

can cause irritation.

TAvoid contact with the skin or eyes.

TRinse off the descaling agent with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be dam-

aged and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

If the descaling operation is interrupted, there may be damage to

the machine.

TAllow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces

(e.g. marble), damage cannot be ruled out.

TClean up any splashes immediately.

EThe descaling programme lasts approximately 45 minutes.

EJURA descaling tablets are available from specialised dealers.

EIf you use a CLARIS Blue filter cartridge and this is activated,

you will not be prompted to descale.

Precondition: DESCALE / ESPRESSO is displayed (example).

cTTouch the Maintenance symbol for approximately 2

seconds.

EMPTY TRAY appears on the display.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

AGENT IN TANK

TRemove and empty the water tank.

TCompletely dissolve the contents of one blister (3 JURA des-

caling tablets) in a receptacle holding 500 ml of water. This

may take several minutes.

TPour the solution into the empty water tank and insert it into

the machine.

SWITCH OPEN, the light segment on the switch lights up.

Descaling the machine

JCAUTION

CAUTION

Downloaded from ManualsNet.com search engine

IMPRESSA C50 – Quick Reference Guide

TCarefully remove the fine foam frother from the Connector

System©by twisting slightly.

TPlace a receptacle (at least 500 ml) under the Connector Sys-

tem©.

hTTurn the switch to the mposition.

DESCALE, water flows out of the Connector System©sev-

eral times. The Maintenance symbol cflashes during the

descaling operation.

The operation is interrupted, SWITCH CLOSE.

jTTurn the switch to the oposition.

DESCALE, the descaling operation is continued.

The operation is interrupted, EMPTY TRAY.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

FILL TANK

TEmpty the receptacle and place it back under the Connector

System©.

TPlace another receptacle under the coffee spout.

TRemove the water tank and rinse it thoroughly.

TFill the water tank with fresh, cold water and reinsert the

tank.

SWITCH OPEN, the light segment on the switch lights up.

hTTurn the switch to the mposition.

DESCALE, the descaling operation is continued.

The operation is interrupted, SWITCH CLOSE.

jTTurn the switch to the oposition.

DESCALE, the descaling operation is continued.

The operation is interrupted, DESCALE.

Water flows out of the coffee spout.

EMPTY TRAY

TRe-assemble the fine foam frother.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

ESPRESSO appears on the display (example). Descaling is

now complete. Your IMPRESSA is once more ready for use.

EIf the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

C50_Kurz/en/201211

Downloaded from ManualsNet.com search engine

Otros manuales para IMPRESSA C50

Tabla de contenidos

Otros manuales de Cafetera de Jura

Jura

Jura Giga X3 Professional Guía de configuración

Jura

Jura IMPRESSA S70 Manual de instrucciones

Jura

Jura IMPRESSA XJ5 Professional Manual de usuario

Jura

Jura ENA 8 Manual de usuario

Jura

Jura J8 Manual de usuario

Jura

Jura IMPRESSA XJ9 Professional Manual de usuario

Jura

Jura IMPRESSA C5 Manual de usuario

Jura

Jura ENA 8 Manual de usuario

Jura

Jura Z6 Manual de usuario

Jura

Jura GIGA X8 Professional Manual de usuario

Jura

Jura ENA 8 Manual de usuario

Jura

Jura S8 Manual de usuario

Jura

Jura IMPRESSA J5 Manual de usuario

Jura

Jura IMPRESSA F50 Classic Manual de usuario

Jura

Jura ENA 8 Manual de usuario

Jura

Jura 729 Manual de usuario

Jura

Jura ENA 8 NAC Manual de usuario

Jura

Jura GIGA G2 Manual de usuario

Jura

Jura J8 Manual de usuario

Jura

Jura 734 Manual de usuario

Jura

Jura GIGA X8 Professional Manual de usuario

Jura

Jura IMPRESSA XJ9 OT TFT Professional Manual

Jura

Jura IMPRESSA E80 Manual de usuario

Jura

Jura Impressa J6 Manual de usuario

Manuales populares de Cafetera de otras marcas

Taurus

Taurus Livorno 6 Manual de usuario

Delta-q

Delta-q QUICK Manual de usuario

Bunn

Bunn LCA-1 Guía de solución de problemas

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instrucciones de instalación

Saeco

Saeco Vienna Plus Sup 018M Manual de usuario

DeLonghi

DeLonghi DC300 Manual de usuario

INCAPTO

INCAPTO BXCO1470E Manual de usuario

Bosch

Bosch TASSIMO finesse TAS16B Series Manual de usuario

Exido

Exido 245-072 Manual de usuario

Animo

Animo OptiVend Choco Manual de usuario

Siemens

Siemens TQ505DF Series Manual de usuario

DeLonghi

DeLonghi ECI341 Manual de usuario

Krups

Krups KT406511 Manual de usuario

Cimbali

Cimbali M32 Classic Manual de usuario

Philips

Philips HL3844N Manual de usuario

Bosch

Bosch TES 515 SERIES Manual de usuario

Tekmatix

Tekmatix TMFM - 65 Manual de usuario

Scarlett

Scarlett SC-CM33005 Manual de usuario