Juniper EX8216 Manual de usuario

Mounting an EX8216 Switch on a Rack or Cabinet

The EX8216 switch ships installed with front-mounting brackets on the chassis for

mounting the switch on a 19-in. equipment rack or cabinet. (The remainder of this

topic uses “rack”to mean “rack or cabinet.”) The switch also comes with adjustable

mounting brackets to support it in the rack.

In a four-post rack, the switch consumes 21 U without the optional power cord tray

and 22 U with the optional power cord tray. Installation in a two-post rack is not

supported. You can mount two switches on a 42 U four-post rack provided that the

rack meets the strength requirements to support the combined weight of the switches.

WARNING: Because of the switch's size and weight, we require the use of a

mechanical lift to install the switch.

CAUTION: If you are installing more than one switch in a rack, install the first switch

at the bottom of the rack.

CAUTION: Do not install line cards in the chassis until after you mount the chassis

securely on a rack.

Before mounting an EX8216 switch on a rack:

1. Verify the site meets the requirements for installation described in Site

Preparation Checklist for an EX8200 Switch.

2. Place the rack in its permanent location, allowing adequate clearance for airflow

and maintenance, and secure it to the building structure. See Clearance

Requirements for Airflow and Hardware Maintenance for an EX8216 Switch for

detailed information.

3. Unpack the switch as described in Unpacking an EX8200 Switch.

4. Install the adjustable mounting brackets at the desired position in a four-post

rack (see Installing Adjustable Mounting Brackets in a Rack or Cabinet for an

EX8200 Switch).

5. Optionally, install the power cord tray, so you can use it to manage the power

supply cords (see Installing the Power Cord Tray in a Rack or Cabinet for an

EX8200 Switch).

6. Read General Safety Guidelines and Warnings for EX Series Switches, with

particular attention to Chassis Lifting Guidelines for EX8200 Switches.

Ensure that you have the following parts and tools available to mount the switch on

a rack:

■A mechanical lift

Mounting an EX8216 Switch on a Rack or Cabinet ■1

■A Phillips (+) screwdriver, number 2 or number 3, depending on the size of

your rack mounting screws

■20 mounting screws appropriate for your rack

To mount the EX8216 switch on a rack (see Figure 2):

1. Install the adjustable mounting brackets at the desired position in a four-post

rack (see Installing Adjustable Mounting Brackets in a Rack or Cabinet for an

EX8200 Switch). If you are planning to install the optional power cord tray, leave

at least 1 U of space below the adjustable mounting brackets (see Installing the

Power Cord Tray in a Rack or Cabinet for an EX8200 Switch). The power cord

tray is optional.

2. Load the switch onto the mechanical lift, making sure it rests securely on the lift

platform. See Figure 1.

Figure 1: Installing the Switch Chassis Using a Mechanical Lift

3. Using the lift, position the switch in front of the rack or cabinet, centering it in

front of the adjustable mounting brackets installed in the rack.

2■Mounting an EX8216 Switch on a Rack or Cabinet

4. Lift the chassis approximately 0.75 in. (1.9 cm) above the surface of the adjustable

mounting brackets. Position the chassis in the rack as close as possible to resting

on the support that the mounting brackets provide.

5. Carefully slide the switch onto the adjustable mounting brackets until the

front-mounting brackets (“ears”) attached to the chassis contact the rack rails,

using the handles on the lower side of the chassis to help guide it into position.

The adjustable mounting brackets installed in the rack ensure that the holes in

the front-mounting brackets align with the holes in the rack rails.

6. Move the lift away from the rack.

7. Ensure the chassis is flush with the front of the rack.

8. Install a mounting screw into each of the open front-mounting holes aligned with

the rack, starting from the bottom.

9. Visually inspect the alignment of the switch. If the switch is installed properly in

the rack, all the mounting screws on one side of the rack are aligned with the

mounting screws on the opposite side and the switch is level.

10. After ensuring that the switch is aligned properly, tighten the screws.

11. Insert 20 mounting screws appropriate for your rack (not provided) into the

aligned holes. Use the appropriate Phillips (+) screwdriver to tighten the screws

to the rack rail.

CAUTION: To meet safety and electromagnetic interference (EMI) requirements and

to ensure proper operation, you must connect EX8200 switches to earth ground

before you connect them to power. For installations that require a separate grounding

conductor to the chassis, use one of the two protective earthing terminals on the

switch chassis to connect to the earth ground. For instructions on connecting an

EX8200 switch to ground using a separate grounding conductor, see Connecting

Earth Ground to an EX Series Switch.

Mounting an EX8216 Switch on a Rack or Cabinet ■3

Figure 2: Installing an EX8216 Switch in a Four-Post Rack

Related Topics ■Removing an EX8216 Switch from a Rack or Cabinet

■Connecting AC Power to an EX8200 Switch

■Connecting DC Power to an EX8200 Switch

■Rack Requirements for an EX8216 Switch

■Cabinet Requirements and Specifications for an EX8216 Switch

Published: 2009-07-15

4■Mounting an EX8216 Switch on a Rack or Cabinet

Otros manuales para EX8216

Tabla de contenidos

Otros manuales de Cambiar de Juniper

Juniper

Juniper Day One+ Instrucciones de instalación

Juniper

Juniper EX8200 Series Manual de usuario

Juniper

Juniper QFX3000-G QFabric Guía de referencia rápida

Juniper

Juniper EX2200 Series Instrucciones de instalación

Juniper

Juniper EX2200 Series Guía

Juniper

Juniper EX2200 Series Manual de usuario

Juniper

Juniper PTX Series Instrucciones de instalación

Juniper

Juniper EX9251 Manual de usuario

Juniper

Juniper EX4500 Series Manual de usuario

Juniper

Juniper EX Series Manual de usuario

Juniper

Juniper OCX1100-48SX Manual de usuario

Juniper

Juniper EX3200 Series Manual de usuario

Juniper

Juniper NETWORK AND SECURITY MANAGER NSM3000 - REV... Manual de usuario

Juniper

Juniper EX3200 Series Manual de usuario

Juniper

Juniper EX2300-24P Manual de usuario

Juniper

Juniper EX4300 Instrucciones de instalación

Juniper

Juniper EX4200 Series Instrucciones de instalación

Juniper

Juniper EX4550 Instrucciones de instalación

Juniper

Juniper EX8200 Series Guía de inicio rápido

Juniper

Juniper EX3400 Manual de usuario

Juniper

Juniper EX Series Manual de usuario

Juniper

Juniper EX2200 Series Manual de usuario

Juniper

Juniper QFX5200-32C-L Manual de usuario

Juniper

Juniper EX4500-40F-FB Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario