Juniper EX Series Manual de instrucciones

Installing a Power Supply in an EX-series Switch

The power supply in EX 3200 and EX 4200 switches is a hot-removable and

hot-insertable field-replaceable unit (FRU): you can remove and replace it without

powering off the switch or disrupting switch functions.

Ensure you have the following parts and tools available to install a power supply in

an EX 3200 or EX 4200 switch chassis:

■Electrostatic discharge (ESD) grounding strap

■Phillips (+) screwdriver, number 2

Before you begin installing a power supply in an EX 3200 or EX 4200 switch, ensure

that you have taken the necessary precautions to prevent ESD damage (see Preventing

Electrostatic Discharge Damage).

To install a power supply in an EX 3200 or EX 4200 switch (see Figure 1 on page 2):

1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to the ESD point on the chassis.

2. Taking care not to touch power supply components, pins, leads, or solder

connections, remove the power supply from its bag.

3. Loosen the locking lever screw on the left front of the power supply by using the

Phillips (+) screwdriver, number 2.

4. Push down on the locking lever until it is in its lowest position.

5. Using both hands, place the power supply in the power supply slot on the rear

panel of the switch and slide it in until it is fully seated.

NOTE: The handle on the 320 W AC power supply is at the bottom of the power

supply faceplate, while the handle on the 600 W and the 930 W AC power supplies

is at the top of the faceplate. The handle on the 190 W DC power supply runs across

the faceplate.

6. Push the locking lever up to its highest position (this action might pull the power

supply in).

7. Tighten the locking lever screw by using the Phillips (+) screwdriver, number 2.

Installing a Power Supply in an EX-series Switch ■1

Figure 1: Installing a Power Supply in an EX 3200 or EX 4200 Switch

NOTE: Each power supply must be connected to a dedicated power source outlet.

NOTE: If you have a Juniper J-Care service contract, register any addition, change,

or upgrade of hardware components at

https://www.juniper.net/customers/csc/management/updateinstallbase.jsp. Failure to do so

can result in significant delays if you need replacement parts. This note applies if

you change the type of power supply or add a new type of uplink module. It does

not apply if you replace these components with the same type of component.

Related Topics ■Removing a Power Supply from an EX-series Switch

■Installing and Removing EX-series Switch Hardware Components

■Power Supply in EX-series Switches

■Field-Replaceable Units in EX-series Switches

■AC Power, Connection, and Power Cord Specifications

■EX 3200 Switch—Rear-Panel Description

■EX 4200 Switch—Rear-Panel Description

2■Installing a Power Supply in an EX-series Switch

Otros manuales para EX Series

15

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Otros manuales de Cambiar de Juniper

Juniper

Juniper QFX3000-G QFabric Manual del operador

Juniper

Juniper QFX5100-48T Manual de usuario

Juniper

Juniper EX8200 Series Manual de usuario

Juniper

Juniper EX3200 Series Manual de usuario

Juniper

Juniper EX4300 Instrucciones de instalación

Juniper

Juniper EX Series Manual de usuario

Juniper

Juniper QFX5120 Series Manual de usuario

Juniper

Juniper QFX5110-32Q Manual de usuario

Juniper

Juniper QFX5230-64CD Instrucciones de instalación

Juniper

Juniper QFX5200-48Y Manual de usuario

Juniper

Juniper EX Series Manual de usuario

Juniper

Juniper QFX5110 Instrucciones de instalación

Juniper

Juniper EX4600 Instrucciones de instalación

Juniper

Juniper QFX5200-48Y Manual de usuario

Juniper

Juniper EX2200 Series Instrucciones de instalación

Juniper

Juniper EX8200 Series Guía de inicio rápido

Juniper

Juniper EX Series Guía de inicio rápido

Juniper

Juniper EX2200 Series Instrucciones de instalación

Juniper

Juniper EX3300 Manual de usuario

Juniper

Juniper EX4550 Manual de usuario

Juniper

Juniper EX4600 Instrucciones de instalación

Juniper

Juniper EX9204 Manual de usuario

Juniper

Juniper EX4300 Manual de usuario

Juniper

Juniper QFX5200-32C-L Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario