Juniper EX4600 Manual de usuario

EX4600 Quick Start

Published

2023-11-06

RELEASE

Table of Contents

Step 1: Begin

Meet the EX4600 | 1

Install the EX4600 | 2

What’s in the Box? | 2

What Else Do I Need? | 3

Rack It | 3

Power On | 4

Step 2: Up and Running

Plug and Play | 6

Customize the Basic Conguraon | 6

Step 3: Keep Going

What’s Next? | 9

General Informaon | 10

Learn With Videos | 11

Step 1: Begin

IN THIS SECTION

Meet the EX4600 | 1

Install the EX4600 | 2

Power On | 4

In this guide, we provide a simple, three-step path, to quickly get you up and running with your new

EX4600. We’ve simplied and shortened the installaon and conguraon steps, and included how-to

videos. You’ll learn how to install an AC-powered EX4600, power it up, and congure basic sengs.

NOTE: Are you interested in geng hands-on experience with the topics and operaons covered

in this guide? Visit Juniper Networks Virtual Labs and reserve your free sandbox today! You’ll nd

the Junos Day One Experience sandbox in the stand alone category. EX switches are not

virtualized. In the demonstraon, focus on the virtual QFX device. Both the EX and QFX

switches are congured with the same Junos commands.

Meet the EX4600

The Juniper Networks® EX4600 oers a compact, highly scalable, high-performance 10GbE soluon for

enterprise campus distribuon deployments as well as low-density data center top-of-rack

environments. A single EX4600 can support up to 72 10GbE ports (using 10GbE breakout cables on

40GbE xed ports) at line rate. In addion, Virtual Chassis technology makes it easy to scale the network

while reducing management complexity. By adding switches to a Virtual Chassis conguraon, you can

grow the number of switch ports without increasing the number of devices to manage.

The base EX4600 model has:

• 24 xed small form-factor pluggable (SFP) or SFP+ access ports

• Four xed quad SFP+ (QSFP+) high-speed uplinks

• Two power supplies

• Five fan modules

• Management interface ports: RJ-45 console (CON) port, RJ-45 management Ethernet port (CO), SFP

management Ethernet port (C1), and a USB port

• Two expansion slots for oponal expansion modules

The EX4600 is available in AC-powered or DC-powered models with air-ow in or air-ow out cooling.

You can install the switch in a two-post or four-post rack. In this guide, we show you how to install an

AC-powered EX4600 in a four-post rack. If you need instrucons for installing a DC-powered EX4600,

see the EX4600 Ethernet Switch Hardware Guide.

Install the EX4600

IN THIS SECTION

What’s in the Box? | 2

What Else Do I Need? | 3

Rack It | 3

Let’s get going and install the EX4600 in a four-post rack.

What’s in the Box?

• EX4600 switch with two power supplies and ve fan modules pre-installed

• Two power cords appropriate for your geographic locaon

• Rack mount kit

The rack mount kit contains one pair of mounng rails, one pair of mounng blades, and 12 at-head

Phillips mounng screws.

What Else Do I Need?

• Someone to help you secure the switch to the rack

• A number two Phillips (+) screwdriver

• Eight rack mount screws

• Cage nuts and washers, if your rack requires them

• Grounding lug and aached cable

• Two 10-32 x 0.25 screws with #10 split-lock washers

• An electrostac discharge (ESD) grounding strap

• Management host, such as a laptop or desktop PC

• Serial-to-USB adapter (if your laptop or desktop PC doesn’t have a serial port)

• An Ethernet cable with RJ-45 connectors aached and an RJ-45 to DB-9 serial port adapter

NOTE: We no longer include a DB-9 to RJ-45 cable or a DB-9 to RJ-45 adapter with a CAT5E

copper cable as part of the device package. If you require a console cable, you can order it

separately with the part number JNP-CBL-RJ45-DB9 (DB-9 to RJ-45 adapter with a CAT5E

copper cable).

Rack It

1. Review General Safety Guidelines and Warnings.

2. Wrap the ESD grounding strap around your bare wrist and ground yourself to an ESD point or to the

rack.

3. Decide which end of the switch you want to place at the front of the rack: the eld-replaceable unit

(FRU) end or the port end. Posion it in the rack so that the AIR IN labels on the power supplies are

next to the cold aisle, and the AIR OUT labels on the power supplies are next to the hot aisle.

4. Aach the mounng rails to each side of the switch using the supplied at-head mounng screws.

5. Li the switch and posion it in the rack. Line up the boom hole in each mounng rail with a hole in

each rack rail, making sure the switch is level.

6. While you’re holding the switch in place, have a second person insert and ghten the rack mount

screws to secure the mounng rails to the rack rails. Make sure they ghten the screws in the two

boom holes rst, and then ghten the screws in the two top holes.

7. Connue holding the switch in place and have the second person slide the mounng blades into the

mounng rail grooves.

8. Screw the mounng blades to the rack using the rack mount screws (and cage nuts and washers, if

your rack requires them).

9. Double-check that the mounng brackets on each side of the rack are level.

Power On

Now that you’ve installed your EX4600 in the rack, you’re ready to connect it to power.

1. Wrap and fasten one end of the ESD grounding strap around your bare wrist, and connect the other

end to one of the ESD grounding points on the chassis.

2. Secure the grounding lug and aached cable to the chassis using two 10-32 x 0.25 screws with #10

split-lock washers. Aach the lug to the chassis through the le rail and blade assembly.

3. Connect the other end of the grounding cable to a proper earth ground, such as the rack. Dress the

grounding cable and ensure that it doesn’t touch or block access to other device components, and

that it doesn’t drape where people could trip over it.

4. Plug in the coupler end of the AC power cord to the AC power cord inlet on each of the switch’s

power supplies.

5. Push the power cord retainer onto the power cord.

6. If the AC power source outlet has a power switch, turn it o.

7. Plug in the power cord to the AC power source outlet.

8. If the AC power source outlet has a power switch, turn it on.

The EX4600 powers up as soon as you connect it to power; there is no power switch. When the AC

and DC LEDs on each power supply are solid green, the EX4600 is ready to use.

Step 2: Up and Running

IN THIS SECTION

Plug and Play | 6

Customize the Basic Conguraon | 6

Now that the EX4600 is powered on, let’s do some inial conguraon to get it up and running on the

network. It’s simple to provision and manage the EX4600 using the CLI.

Plug and Play

The EX4600 switch ships with factory-default sengs that enable plug-and-play operaon. These

sengs load as soon as you power on the switch.

Customize the Basic Conguraon

You can easily customize the factory-default conguraon using CLI commands. You can revert to the

factory-default conguraon whenever you want.

Have the following informaon handy before you begin customizing switch sengs:

• Hostname

• Root authencaon password

• Management port IP address

• Default gateway IP address

•(Oponal) SNMP read community, locaon, and contact informaon

1. Verify that the serial port sengs for your laptop or desktop PC are set to the default:

• Baud Rate—9600

• Flow Control—None

• Data—8

• Parity—None

• Stop Bits—1

• DCD State—Disregard

2. Connect the console (CON) port on the switch’s management panel to a laptop or desktop PC using

the RJ-45 cable and RJ-45 to DB-9 adapter (not provided).

NOTE: If your laptop or desktop PC doesn't have a serial port, use a serial-to-USB adapter

(not provided).

3. At the Junos OS login prompt, type root to log in. You don't need to enter a password. If the

soware booted before you connected the laptop or desktop to the console port, you might need

to press the Enter key for the prompt to appear.

4. Start the CLI.

root@% cli

5. Enter conguraon mode.

root> configure

6. Add a password for the root administraon user account.

[edit]

root@# set system root-authentication plain-text-password

New password:

password

Retype new password:

password

7. (Oponal) Congure the name of the switch. If the name includes spaces, enclose the name in

quotaon marks (“ ”).

[edit]

root@# set system host-name

host-name

8. Congure the default gateway.

[edit]

root@# set routing-options static route default next-hop

address

9. Congure the IP address and prex length for the switch management interface.

[edit]

root@# set interfaces em0 unit 0 family inet address

address/prefix-length

NOTE: Although the CLI lets you congure two management Ethernet interfaces within the

same subnet, only one interface is usable and supported at any point in me.

NOTE: The management ports, em0 (labeled C0), and em1 (labeled C1), are on the switch’s

management panel.

10. Congure the stac routes to remote prexes with access to the management port.

[edit]

root@# set routing-options static route remote-prefix next-hop

destination-ip

retain no-

readvertise

11. Enable Telnet service.

[edit]

root@# set system services telnet

NOTE: When Telnet is enabled, you cannot log in to the EX4600 through Telnet using root

credenals. Root login is allowed only for SSH access.

12. Commit the conguraon. Your changes become the acve conguraon for the switch.

[edit]

root@# commit

Otros manuales para EX4600

Tabla de contenidos

Otros manuales de Cambiar de Juniper

Juniper

Juniper EX Series Manual de instrucciones

Juniper

Juniper QFX5100-48T Manual de usuario

Juniper

Juniper EX8200 Series Manual de usuario

Juniper

Juniper EX2300 Series Manual de usuario

Juniper

Juniper EX9208 Manual de usuario

Juniper

Juniper EX Series Manual de usuario

Juniper

Juniper QFX5220-128C Manual de usuario

Juniper

Juniper QFX3600 Manual del operador

Juniper

Juniper EX2200 Series Guía

Juniper

Juniper EX8200 Series Manual de usuario

Juniper

Juniper EX4500 Series Instrucciones de instalación

Juniper

Juniper EX8200 Series Manual de instrucciones

Juniper

Juniper EX3200 Series Instrucciones de instalación

Juniper

Juniper EX3300 Manual de usuario

Juniper

Juniper EX9251 Manual de usuario

Juniper

Juniper EX Series Manual de usuario

Juniper

Juniper EX9214 Instrucciones de instalación

Juniper

Juniper EX4600 Instrucciones de instalación

Juniper

Juniper EX2200-C Manual de usuario

Juniper

Juniper QFX5120 Series Manual de usuario

Juniper

Juniper QFX10016 Instrucciones de instalación

Juniper

Juniper EX8216 Instrucciones de instalación

Juniper

Juniper EX4300 Instrucciones de instalación

Juniper

Juniper EX4600 Instrucciones de instalación

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario