Juniper PTX3000 Manual de usuario

PTX3000 Packet Transport Router

Quick Start

January 2014

Part Number: 530-056448

Revision 01

This document describes how to install the PTX3000 Packet Transport Router.

Contents QuickStartDescription...............................................3

Step 1: Prepare the Site for the PTX3000 Packet Transport Router . . . . . . . . . . . . 3

Rack-MountingRequirements......................................3

Tools Required to Unpack and Prepare the PTX3000 Packet Transport

RouterforInstallation.........................................5

Step 2: Unpack the PTX3000 Packet Transport Router . . . . . . . . . . . . . . . . . . . . . . 5

Step 3: Install the PTX3000 Packet Transport Router Mounting Hardware . . . . . . 5

InstallCageNuts,IfNeeded........................................5

InstalltheMountingShelf.........................................6

Step 4: Install the PTX3000 Packet Transport Router . . . . . . . . . . . . . . . . . . . . . . . 7

Install the Packet Transport Router By Using a Lift . . . . . . . . . . . . . . . . . . . . . . 7

Step 5: Connect the PTX3000 Packet Transport Router Grounding Cable . . . . . . 12

Step 6: Connect External Devices and PIC Cables to the PTX3000 Packet

TransportRouter................................................14

Connect the PTX3000 to a Console or Auxiliary Device . . . . . . . . . . . . . . . . . 14

Connect the PTX3000 to a Network for Out-of-Band Management . . . . . . . 15

ConnectPICCablestothePTX3000................................16

Step 7: Connect the PTX3000 Packet Transport Router to Power . . . . . . . . . . . . . 19

Connect DC Power to the PTX3000 DC Power Supply Modules . . . . . . . . . . 19

Connect Nonredundant DC Power to the PTX3000 DC Power Supply

Modules................................................19

Connect Redundant DC Power to the PTX3000 DC Power Supply

Modules ...............................................20

Connect AC Power to the PTX3000 AC Power Supply Modules . . . . . . . . . . 24

Connect Nonredundant AC Power to the PTX3000 AC Power Supply

Modules ...............................................24

Connect Redundant AC Power to the PTX3000 AC Power Supply

Modules ...............................................24

Step 8: Power On the PTX3000 Packet Transport Router . . . . . . . . . . . . . . . . . . . 26

Power On the DC-Powered PTX3000 Packet Transport Router . . . . . . . . . . 26

Power On the AC-Powered PTX3000 Packet Transport Router . . . . . . . . . . . 27

Step 9: Install the Card Cage Screens on the PTX3000 Packet Transport

Router ........................................................28

Step 10: Perform the PTX3000 Packet Transport Router Initial Software

Configuration...................................................29

EnterConfigurationMode.........................................29

Configure User Accounts and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

ConfigureSystemAttributes......................................30

CommittheConfiguration.........................................31

SafetyWarnings....................................................33

ComplianceStatementsforNEBS.....................................35

Compliance Statements for EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Canada .......................................................35

European Union ................................................35

Junos OS Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

RequestingTechnicalSupport........................................36

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

OpeningaCasewithJTAC........................................36

Revision History ....................................................37

PTX3000 Packet Transport Router Quick Start

Quick Start Description

This Quick Start contains information you need to install and configure the packet

transport router quickly. For complete installation instructions, see the PTX3000 Packet

Transport Router Hardware Guide at http://www.juniper.net/techpubs/hardware/.

WARNING: This Quick Start contains a summary of safety warnings in “Safety

Warnings” on page 33. For a complete list of warnings for this packet transport

router, including translations, see the PTX3000 Packet Transport Router

Hardware Guide at http://www.juniper.net/techpubs/hardware/.

The packet transport router is a complete routing system that provides 10-Gigabit

Ethernet, 40-Gigabit Ethernet, and 100-Gigabit Ethernet interfaces for large networks

and network applications. The packet transport router supports up to eight Flexible PIC

Concentrators (FPCs). It provides up to 3.84 terabits per second (Tbps) per second, full

duplex (1.92 Tbps per second of any-to-any, nonblocking, half-duplex) switching.

The packet transport router is shipped in a wooden crate. A wooden pallet forms the

base of the crate. The packet transport router chassis is bolted to this pallet. The shipping

crate contains:

•One accessory box (the box to which this Quick Start is taped)

•One Juniper Networks PTX3000 Packet Transport Router

•One Quick Start (this document)

Step 1: Prepare the Site for the PTX3000 Packet Transport Router

Before installing the packet transport router, make sure that the site meets all the power,

environmental, and clearance requirements. See the site preparation guidelines in the

PTX3000 Packet Transport Router Hardware Guide.

•Rack-Mounting Requirements on page 3

•Tools Required to Unpack and Prepare the PTX3000 Packet Transport Router for

Installation on page 5

Rack-Mounting Requirements

•You can install the packet transport router in many types of racks, including a four-post

rack or cabinet or an open-frame rack. The chassis is 38.5 in. (97.8 cm) high, 8.7 in.

(22.1 cm) deep, and 17.6 in. (44.7 cm) wide. The cable management system on the

front of the chassis adds 1.9 in. (4.8 cm) to the depth, for a total depth of 10.6 in.

(26.9 cm). The outer edges of the mounting brackets extend the width to 19 in.

(48.3 cm). See Figure 1 on page 4.

•The rack rails must be spaced widely enough to accommodate the external dimensions

of the PTX3000 chassis. The chassis is 17.6 in. (44.7 cm) wide.

Quick Start Description

NOTE: The mounting brackets extend the width to fit into standard 19-in.

(48.3 cm) racks. The rack rails must be spaced widely enough to

accommodate the external dimensions of the PTX3000 chassis.

•The rack must be strong enough to support the weight of the fully configured packet

transport router, up to about 200 lb (90.7 kg).

•For service personnel to remove and install hardware components, there must be

adequate space in front of the packet transport router. At least 24 in. (61.0 cm) in front

of the rack or cabinet is required. However, NEBS GR-63 recommends at least 30 in.

(76.2 cm) in front of the rack or cabinet. See Figure 1 on page 4.

•The rack or cabinet must have an adequate supply of cooling air.

•In a closed cabinet, we recommend at least 6 in. (15 cm) of unobstructed airflow in

front of the packet transport router, and 1 in. (2.5 cm) of unobstructed airflow behind

the packet transport router.

•Appropriate measures such as airflow baffles must be installed to prevent recirculation

of hot air and overheating.

Figure 1: Chassis Dimensions and Clearance Requirements

PTX3000 Packet Transport Router Quick Start

Tools Required to Unpack and Prepare the PTX3000 Packet Transport Router for Installation

The following tools and parts are required to unpack and prepare the PTX3000 router

for installation:

•A mechanical lift—recommended

•1/2-in. (13-mm) open-end or socket wrench to remove bracket bolts from the shipping

pallet

•Phillips screwdrivers, numbers 1 and 2

•7/16-in. (11-mm) nut driver, for tightening nuts to the terminal studs on each power

distribution unit on a DC-powered packet transport router

CAUTION: You must use an appropriate torque-controlled tool to tighten

the nuts. Applying excessive torque damages the terminal studs. The

maximum torque that may be applied to this nut is 24 lb-in. (2.7 Nm).

•Cage nuts, if needed for your rack or cabinet

•Electrostatic discharge (ESD) wrist strap, to be used when handling electronic

components

•Antistatic mat, to be used when installing or removing components from the chassis

•Blank panels to cover any slots not occupied by a component

Step 2: Unpack the PTX3000 Packet Transport Router

For detailed instructions on how to unpack the shipping crate and verifying the parts

received, see the PTX3000 Packet Transport Router Hardware Guide.

Step 3: Install the PTX3000 Packet Transport Router Mounting Hardware

To install the mounting hardware, perform the following procedures:

•Install Cage Nuts, If Needed on page 5

•Install the Mounting Shelf on page 6

Install Cage Nuts, If Needed

Insert cage nuts on the front rack rails, if needed. The hole distances are relative to the

standard U division on the rack that is aligned with the bottom of the mounting shelf.

To install cage nuts on the front rack rails:

1. Insert cage nuts in the holes specified for the mounting shelf (see Table 1 on page 6).

NOTE: A mounting shelf is not required to install the packet transport

router.

Tools Required to Unpack and Prepare the PTX3000 Packet Transport Router for Installation

Table 1: Mounting Hole Locations for Installing a PTX3000 Mounting Shelf

Distance Above U DivisionHole

0.01 U0.02 in. (.06 cm)1

0.08 U0.2 in. (0.4 cm)2

2. Insert cage nuts in the holes specified for mounting the chassis (see

Table 2 on page 6).

Table 2: Mounting Hole Locations for Installing a Chassis

Distance Above U DivisionHole

2.8 U4.9 in. (12.5 cm)1

8.8 U15.4 in. (39.1 cm)2

17.1 U29.9 in. (76.0 cm)3

Install the Mounting Shelf

Optionally, you can install the mounting shelf before mounting the chassis in the rack.

To install the mounting shelf (see Figure 2 on page 6):

1. Align the mounting shelf with the mounting holes on the rack rail.

2. Partially insert a mounting screw appropriate for your rack into the holes specified in

Table 1 on page 6.

3. Tighten all the screws completely to secure the mounting shelf to the rack rails.

Figure 2: Installing the Mounting Hardware

PTX3000 Packet Transport Router Quick Start

Step 4: Install the PTX3000 Packet Transport Router

Because of the size and weight of the device, we recommend that you install the packet

transport router by using a mechanical lift.

•Install the Packet Transport Router By Using a Lift on page 7

Install the Packet Transport Router By Using a Lift

CAUTION: Before installing the PTX3000 Packet Transport Router:

•Verify that a mechanical lift is available for the installation.

•Have a qualified technician verify that the rack is strong enough to support

the chassis weight and is adequately supported at the installation site.

•Ensure that the rack is in its permanent location and is secured to the

building.

•Ensure that the installation site allows adequate clearance for both airflow

and maintenance.

NOTE: A mounting shelf is not required to install the packet transport router.

To install the packet transport router using a lift (see Figure 3 on page 9 and

Figure 4 on page 10):

1. Load the packet transport router onto the lift, making sure the packet transport router

rests securely on the mechanical lift.

CAUTION: Do not lift the packet transport router by using the handles on

the front-mounting flanges. Use these handles only to help position the

packet transport router.

2. Using the lift, position the packet transport router in front of the rack. Lift the chassis

slightly above the position you plan to install it, and position it as close as possible to

the rack.

3. With two people in front, push the front-mounting flanges to slide the packet transport

router into the rack until the front-mounting flanges contact the rack rails. The

front-mounting flanges of the chassis align with the holes in the rack rails.

4. Install a mounting screw into each of the mounting holes aligned with the rack, starting

from the bottom (Table 3 on page 8). Use an appropriate screwdriver to tighten all

the screws completely.

Visually inspect the alignment of the packet transport router. If the packet transport

router is installed properly in the rack, all the mounting screws on one side of the rack

Step 4: Install the PTX3000 Packet Transport Router

should be aligned with the mounting screws on the opposite side, and the packet

transport router should be level.

5. Move the lift away from the rack.

6. If you are installing two to four routers in the rack, repeat this procedure for each router.

See Figure 5 on page 11 and Figure 6 on page 12 for examples of multiple routers

installed in a single rack.

Table 3: Mounting Hole Locations for Installing a Chassis in a Rack

Distance Above U DivisionHole

2.8 U4.9 in. (12.5 cm)1

8.8 U15.4 in. (39.1 cm)2

17.1 U29.9 in. (76.0 cm)3

PTX3000 Packet Transport Router Quick Start

Figure 3: Loading the PTX3000 onto the Lift

Install the Packet Transport Router By Using a Lift

Figure 4: Installing the PTX3000 in a Rack

PTX3000 Packet Transport Router Quick Start

Otros manuales para PTX3000

Tabla de contenidos

Otros manuales de Hardware de red de Juniper

Juniper

Juniper CTP2000 Series Instrucciones de instalación

Juniper

Juniper NFX150-S1 Manual de usuario

Juniper

Juniper ACX7100 Manual de usuario

Juniper

Juniper ACX7100-32C Manual de usuario

Juniper

Juniper MX150 Manual de usuario

Juniper

Juniper NETSCREEN-5XP Manual de usuario

Juniper

Juniper SRX300 Series Instrucciones de instalación

Juniper

Juniper JATP700 Instrucciones de instalación

Juniper

Juniper JSA7800 Manual de usuario

Juniper

Juniper SSR1400 Manual de usuario

Juniper

Juniper Day One Plus SRX380 Manual de usuario

Juniper

Juniper EX9200 Series Manual de usuario

Juniper

Juniper MX10004 Instrucciones de instalación

Juniper

Juniper CTP2000 Series Manual de usuario

Juniper

Juniper G10 CMTS Instrucciones de instalación

Juniper

Juniper DUAL-PORT T1-E1 GPIMS Manual de usuario

Juniper

Juniper NFX150 Manual de usuario

Juniper

Juniper SSR1200 Manual de usuario

Juniper

Juniper STRM 5000 Manual

Juniper

Juniper Day One+ QFX5120 Manual de usuario

Juniper

Juniper SRX5400 Manual de servicio

Juniper

Juniper QFX Series Manual de usuario

Juniper

Juniper SSR1400 Manual de usuario

Juniper

Juniper Junos Space JA1500 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario