Juniper SSR1200 Manual de usuario
Quick Start Guide
SSR1200
IN THIS GUIDE
Step 1: Begin | 1
Step 2: Up and Running | 5
Step 3: Keep Going | 15
Step 1: Begin
SUMMARY
In this guide, we provide a simple, three-step path, to quickly
get the Juniper Networks® SSR1200 appliance up and
running on Juniper Mist™ cloud. You'll learn how to install,
power on, and congure basic sengs for an AC-powered
SSR1200 appliance.
IN THIS SECTION
Meet the SSR1200 | 1
Install the SSR1200 | 2
Power On | 4
Meet the SSR1200
The SSR1200 is a 1 U xed conguraon appliance that's ideal for large branch and small data center or campus
deployments. Powered by the Juniper® Session Smart Router (SSR) soware, the SSR1200 provides secure and resilient
WAN connecvity.
The SSR1200 has seven 1 GbE ports, four 1/10 GbE SFP+ ports, a management port (for Mist operaons), 64 GB of
memory, and a 256 GB enterprise-grade solid-state drive (SSD) for storage.
Install the SSR1200
IN THIS SECTION
What's in the Box? | 2
What Else Do I Need? | 2
Rack It | 3
What's in the Box?
Along with your SSR1200, you’ll nd:
• RJ-45 to USB A serial cable
• AC power cord (country-specic)
• Rack mount kit
• Two front mounng brackets
• Two side mounng rails
• Two rear mounng blades
• Eight rack screws and cage nuts
• Fourteen M4 at-head screws
What Else Do I Need?
• Number 2 or 3 Phillips (+) screwdriver, depending on the size of your rack screws
• A management host such as a laptop or desktop PC
• A grounding cable
CAUTION: Ensure that a licensed electrician has aached the appropriate grounding lug to your
grounding cable. Using a grounding cable with an incorrectly aached lug can damage the SSR1200.
2
Rack It
Here’s how to install the SSR1200 in a four-post rack:
1. Review the General Safety Guidelines and Warnings.
2. Wrap and fasten one end of the electrostac discharge (ESD) cable grounding strap around your bare wrist, and
connect the other end to a site ESD point.
3. Aach the front mounng brackets to the front of the chassis, using six M4 at-head screws. Then aach the side
mounng rails to the chassis, using eight M4 at-head screws.
4. Grasp both sides of the SSR1200 chassis, li it, and posion it in the rack so that the front mounng bracket holes
align with the threaded holes in the rack rail.
NOTE: Ensure that the rear of the appliance is supported while you mount the SSR1200 in the rack.
5. While you’re holding the SSR1200 in place, have a second person insert and ghten the rack-mount screws to
secure the front mounng brackets to the rack rails. Tighten the screws in the two boom holes rst, then ghten
the screws in the two top holes.
6. Connue to support the SSR1200 in place and have the second person slide the rear mounng blades into the
channels of the side mounng rails.
7. Secure the rear mounng blades on each side of the chassis to the rack post, using rack mounng screws.
3
8. Check that the front mounng brackets on each side of the rack are lined up with each other.
9. Aach a grounding cable to earth ground and then aach the other end to the SSR1200 grounding point.
10. Dress the grounding cable. Ensure that it doesn’t touch or block access to other device components, and that it
doesn’t drape where people could trip over it.
Power On
Now that you’ve installed your SSR1200 in the rack and grounded the chassis, you’re ready to connect it to power.
The SSR1200 supports redundant AC power supplies that are pre-installed at the factory. It comes with two AC power
supplies preinstalled on the rear of the device.
1. Wrap and fasten one end of the ESD grounding strap around your bare wrist, and connect the other end to one of
the ESD grounding points on the router.
2. Turn o the power switch on the SSR1200.
3. Make sure that the power supplies are fully inserted in the chassis.
4. Push the end of the power cord retainer strip into the hole next to the power supply socket unl it snaps into
place. Ensure that the loop in the retainer strip faces the power supply socket.
4
5. Press the small tab on the retainer strip to loosen the loop. Slide the loop unl there is enough space to insert the
power cord coupler through the loop into the power supply socket.
6. Insert the power cord coupler rmly into the power supply socket.
7. Slide the loop toward the power supply socket unl it is snug against the base of the coupler.
8. Press the tab on the loop and draw out the loop into a ght circle.
9. If the AC power source outlet has a power switch, turn it o.
10. Plug in each power cord to an AC power source outlet.
WARNING: Ensure that the power cord does not block access to the appliance components or
drape where people can trip on it.
11. If the AC power source outlet has a power switch, turn it on.
12. Turn on the power switch on the SSR1200.
Step 2: Up and Running
IN THIS SECTION
Connect Your SSR1200 to the Mist Cloud | 6
Claim Your Appliance | 7
Add the Network | 8
5
Add Applicaons | 9
Create a Template | 10
Assign the Template to a Site | 14
Assign the SSR1200 to a Site | 14
Now that the SSR1200 is powered on, let's get it up and running on Juniper Mist™ cloud. Ensure that you have a
Juniper Mist WAN Assurance subscripon, and log in credenals for the Juniper Mist portal.
Connect Your SSR1200 to the Mist Cloud
Your SSR1200 uses port MGMT (mgmt-0/0/0) as the default port to contact Mist for zero-touch provisioning (ZTP). You
will also be seng up port 3 (ge-0/0/3) with a LAN network.
1. Connect the MGMT port to an Ethernet WAN link capable of providing the SSR1200 with:
• DHCP address assignment
•Connecvity to the Internet and Mist
2. Connect port 3 to your LAN devices, such as
• Mist-managed Juniper EX switches
• Mist APs
• User devices
3. Power on the SSR1200.
Your SSR1200 is now connected to the Mist cloud.
6
Claim Your Appliance
IN THIS SECTION
Enter the Mist Claim Code | 7
Mist AI App QR Scan | 8
To add the SSR1200 to your organizaon's WAN Edge inventory, you must enter the SSR1200 claim informaon into
Mist. The claim label (QR code scker) on the front panel has the claim informaon.
To enter the claim informaon, do one of the following:
• Enter the claim code in Mist. The claim code is the number above the QR code. For example: In this picture, the claim
code is K6TAACRTCJWQ8GQ.
• Scan the QR code with the Mist mobile applicaon.
Enter the Mist Claim Code
1. Log in to your organizaon on the Juniper Mist cloud.
2. Select Organizaon > Inventory from the menu on the le, then select the WAN Edges tab at the top.
3. Click Claim WAN Edges in the upper right poron of the inventory screen.
4. Enter the SSR1200 claim code and click Add.
5. Uncheck the Assign claimed WAN Edges to site check box to place the SSR1200 in the inventory. The SSR1200 is
assigned to a site later.
6. Click the Claim buon to claim the SSR1200 into your inventory.
Video: Add the Claim Informaon in Mist
7
Mist AI App QR Scan
You can download the Mist AI App from the Mac App Store or from Google Play Store.
1. Open the Mist AI app.
2. Click Claim Devices to Org.
3. Scan the QR code.
Add the Network
Add the network to be used for accessing applicaons over a LAN network segment.
1. Select Organizaon > Networks from the menu on the le.
2. Click Add Networks in the upper-right corner of the Networks page.
Video: Access the Add Networks Page
3. Enter a name for the network.
4. Enter the network subnet as 192.168.1.0/24.
8
5. Click Add.
This network is now dened for use across the enre organizaon, including the template that you will apply to your
SSR1200.
Add Applicaons
1. Select Organizaon > Applicaons from the menu on the le.
2. Click Add Applicaons in the upper-right corner of the Applicaons page.
Video: Access the Add Applicaons Page
3. Enter the name for the applicaon as Internet.
4. Enter 0.0.0.0/0, or all IPv4 address space in the IP Addresses eld.
9
5. Click Add.
Your organizaon is now set up to provide access to the Internet using the WAN.
Create a Template
Excellent! Now you have the SSR1200 waing to be claimed, a network for your LAN, and an Internet applicaon for
your WAN. Next, you need to create a WAN Edge template that es them all together! Templates are reusable and keep
the conguraon consistent for every SSR1200 you deploy.
1. Select Organizaon > WAN Edge Templates from the menu on the le.
2. Click Create Template in the upper-right corner of the WAN Edge Templates page.
3. Enter a name for the template.
4. Click Create.
5. Enter the NTP and DNS informaon for the WAN edge device.
Video: Create the Template
Congure the WAN Port
The rst thing to do in your template is to describe which port to use for the WAN.
1. Scroll to the WAN secon of the template, and click Add WAN.
2. Enter the name for the WAN port as wan1.
Video: Add WAN Conguraon
10
Otros manuales para SSR1200
1
Tabla de contenidos
Otros manuales de Hardware de red de Juniper
Juniper
Juniper G10 CMTS Instrucciones de instalación
Juniper
Juniper SSR130 Instrucciones de instalación
Juniper
Juniper EX8208 Manual de usuario
Juniper
Juniper CTP2000 Series Instrucciones de instalación
Juniper
Juniper Junos Space JA2500 Instrucciones de instalación
Juniper
Juniper MX SERIES - FAN TRAY UPGRADE REV1 4-2010 Manual de usuario
Juniper
Juniper MX10016 Instrucciones de instalación
Juniper
Juniper SSR130 Manual de usuario
Juniper
Juniper NFX250 Manual de usuario
Juniper
Juniper T1600 Manual de usuario
Juniper
Juniper Day One+ QFX5120 Manual de usuario
Juniper
Juniper NFX150 Manual de usuario
Juniper
Juniper JSA7800 Manual de usuario
Juniper
Juniper CSE2000 Manual
Juniper
Juniper QFX Series Manual de usuario
Juniper
Juniper JSA3800 Instrucciones de instalación
Juniper
Juniper NSM4000 Instrucciones de instalación
Juniper
Juniper SRX320 Manual de usuario
Juniper
Juniper EX4100-48P/T Manual de usuario
Juniper
Juniper SSR1500 Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
