Juniper SRX380 Manual de usuario

Quick Start Guide

SRX380 Services Gateway

IN THIS GUIDE

SRX380 Services Gateway Overview | 1

SRX380 Front Panel and Rear Panel | 2

SRX380 Services Gateway Physical Specifications | 3

Factory-Default Settings | 3

Install the SRX380 in a Rack | 4

Connect to Ground | 6

Connect Power to the Device | 7

Configure Root Authentication | 8

Plug and Play | 9

Configure the SRX380 Using J-Web | 10

Next Steps | 11

SRX380 Services Gateway Overview

The Juniper Networks SRX380 Services Gateway consolidates security, routing, switching to provide an all-in-one

networking platform for SD-WAN and NGFW deployments. The services gateway is designed for enterprise (large branch

offices, small campus, SD-WAN) and service provider (managed WAN CPE, SD-WAN) deployments. For more information

on the SRX380 hardware, see the SRX380 Services Gateway Hardware Guide.

addition or change to the installation base or if the installation base is moved. Juniper Networks will not be held accountable

for not meeting the hardware replacement service-level agreement for products that do not have registered serial numbers

or accurate installation base data.

Update your installation base at https://www.juniper.net/customers/csc/management/updateinstallbase.jsp.

SRX380 Front Panel and Rear Panel

Figure 1: SRX380 Front Panel Components

g100930

ALARM

PWR

mPIM1

mPIM2

mPIM3

mPIM4

mPIM 12

T TS

3 4

0 / 8 0/9 0 / 10 0/ 11 0 / 12 0/ 13 0 / 14 0/ 15 0 / 16 0 / 17 0/ 18 0/ 19

124

6791011 8

21 45

7—1—1-Gigabit Ethernet portsLEDs

8—2—Management portReset Config button

9—3—USB portMini-USB console port

10—4—RJ-45 console portMini-PIM slots

11—5—Power buttonESD outlet

6—1-Gigabit Ethernet or 10-Gigabit Ethernet SFP/SFP+ ports

Figure 2: SRX380 Rear Panel Components

g100933

3—1—Power supply inputGrounding point

4—2—SSD slotFans

SRX380 Services Gateway Physical Specifications

Table 1 lists the physical specifications for the services gateway.

Table 1: Physical Specifications for the SRX380 Services Gateway

ValuePhysical Specification of Chassis

With handles—20.47 in. (52 cm)

Without handles—18.7 in. (47.5 cm)

Depth

17.36 in. (44.09 cm)Width

1.72 in. (4.37 cm)Height

15 lb (6.80 kg)Weight (with single power supply unit)

Factory-Default Settings

The SRX380 device is shipped with the with the factory-default settings listed in Table 2,Table 3,Table 4, and Table 5.

Table 2: Security Policies

Policy ActionDestination ZoneSource Zone

permittrusttrust

permituntrusttrust

Table 3: NAT Rules

Policy ActionDestination ZoneSource Zone

Source NAT to untrust zone interfaceuntrusttrust

Table 4: Ethernet Interfaces

IP AddressDHCP StateSecurity ZoneInterfacePort Label

UnassignedClientuntrustge-0/0/0 and xe-0/0/190/0 and 0/19

Table 4: Ethernet Interfaces (continued)

IP AddressDHCP StateSecurity ZoneInterfacePort Label

192.168.2.1/24ServertrustVLAN Interface irb.0

(ge-0/0/1 to ge-0/0/15)

(xe-0/0/16 to xe-0/0/18)

0/1 to 0/18

192.168.1.1/24Serverfxp0MGMT

Table 5: LTE Interfaces

IP AddressSecurity ZoneInterface

N/AN/Acl-1/0/0

ISP assigned*untrustdl0 (logical)

*Only if the LTE Mini-PIM is present

The SRX380 device is shipped with the following services and protocols enabled by default:

Table 6: Services, Protocols, and Startup Mode

Device Startup ModeProtocolsServices

SwitchingRSTP (all interfaces)SSH

HTTPS

NETCONF over SSH

To provide secure traffic, a basic set of screens are configured on the untrust zone.

Install the SRX380 in a Rack

You can install the SRX380 in a four-post rack. The rack mounting kit is shipped with the device. Before you start:

•Review the General Safety Guidelines and Warnings

•Have someone on hand to help you install the SRX380

•Make sure you have a number 2 Phillips screwdriver and screws to secure the chassis to the rack

•Check the SRX380 package for the following:

•RJ-45 cable

•DB-9 adapter

•USB cable

•Power cord

•Power cord retainer clip

•Rack mounting kit containing the following:

•6 flat-head 4-40 mounting screws

•12 flat-head M4x6-mm Phillips mounting screws

•Four mounting brackets (includes two 2-inch-recess brackets) that attach to the mounting rails

•One pair of mounting rails

•One pair of mounting blades

To install the SRX380 in a rack:

1. Secure the front-mounting brackets to the side-mounting rails using the six flat-head mounting screws.

g100945

2—1—Mounting-railMounting bracket

2. Secure the mounting rails to the sides of the SRX380 using the M4x6-mm Phillips flat-head mounting screws.

g100946

3. Lift the SRX380 and position it in the rack. Line up the bottom hole in each mounting bracket with a hole in each rack

rail, making sure the SRX380 is level.

4. While you’re holding the SRX380 in place, have a second person insert and tighten the rack mount screws to secure

the mounting brackets to the rack rails. Make sure they tighten the screws in the two bottom holes first and then

tighten the screws in the two top holes next.

g100947

5. Continue holding the SRX380 in place and have the second person slide the mounting blades into the channel of the

mounting rails. Secure the blades to the rack using the rack mount screws.

g100948

6. Check that the mounting brackets on each side of the rack are lined up with each other.

Connect to Ground

To ground the device:

1. Wrap and fasten one end of the ESD grounding strap around your wrist and connect the other end to a site ESD point.

2. Connect the grounding cable to a proper earth ground, such as the rack in which the device is mounted.

3. Remove the two screws on the rear of the chassis using a Phillips screwdriver.

4. Place the grounding cable lug attached to the grounding cable over the grounding point on the rear of the chassis. See

Figure 3.

Figure 3: Connecting the Grounding Cable to the SRX380 Services Gateway

g100950

5. Secure the grounding cable lug to the grounding point with the washers and screws.

6. Dress the grounding cable and verify that it does not touch or block access to the services gateway components and

that it does not drape where people could trip on it.

Connect Power to the Device

To connect AC power to the device:

1. Push the end of the power cord retainer strip into the slot above the power cord inlet until the strip snaps into place.

Ensure that the loop in the retainer strip faces the power cord (see Figure 4).

The power cord retainer clip extends out of the chassis by 3 in. (7.62 cm).

2. Press the small tab on the retainer strip to loosen the loop. Slide the loop until there is enough space to insert the

power cord coupler into the power cord inlet.

3. Insert the power cord coupler firmly into the power cord inlet (see Figure 4).

4. Slide the loop toward the power supply until it is snug against the base of the coupler.

Figure 4: Connecting an AC Power Cord

g100940

5. Press the tab on the loop and draw out the loop into a tight circle.

6. If the AC power source outlet has a power switch, set it to the OFF (0) position.

7. Insert the power cord plug into an AC power source outlet.

8. If the AC power source outlet has a power switch, set it to the ON (|) position.

If the power supply is installed correctly and functioning normally, the LED on the faceplate of the power supply glows

solid green.

The device starts automatically as the power supply completes its startup sequence. The PWR LED lights up during

startup and remains on when the device is operating normally.

NOTE: After the power supply is turned on, it can take up to 60 seconds for status indicators—such as the

STAT and PWR LEDs—to show that the power supply is functioning normally. Ignore error indicators that

appear during the first 60 seconds.

Configure Root Authentication

To configure root authentication:

1. Connect one end of the Ethernet cable to the management port (labeled MGMT) on the device.

2. Connect the other end of the Ethernet cable to the management device.

Figure 5: Connecting the SRX380 to a Management Device

g100951

The SRX380 functions as a DHCP server and automatically assigns an IP address to the laptop.

3. Ensure that the laptop acquires an IP address on the 192.168.1.0/24 network.

4. If the laptop is unable to acquire an IP address, manually configure an IP address in the 192.168.1.0/24 network. Be

sure you don’t assign the IP address 192.168.1.1 to the laptop as this is the IP address assigned to the SRX380.

5. Open a browser and type https://192.168.1.1. No login is required.

The J-Web Setup wizard opens on your screen.

6. Click Skip in the upper-right corner of the Setup wizard.

7. Set a root authentication password and click OK.

The J-Web login page appears.

8. Log in using the root authentication password.

The J-Web Setup application displays.

Plug and Play

The SRX380 already has factory-default settings configured to make it a plug and play device. So all you have to do to

get the SRX380 up and running is connect it to your LAN and WAN networks.

1. Connect the WAN network to port 0/0 or 0/19.

2. Connect the LAN network to any of the ports from 0/1 through 0/18.

3. Check to see if the SRX380 is connected to the Internet. Go to http://www.juniper.net. If the page does not load,

check the Internet connection.

After you complete these steps, you can start using the SRX380 on your network right away. You can go back and customize

settings at anytime. The J-Web Setup wizard is always available to you.

Configure the SRX380 Using J-Web

You can modify the configuration using J-Web. Have the following information ready before you start the configuration

process:

•Hostname

•Root authentication password

•IP address for the NTP server

•IP address for the DNS server

•IP address for the management interface

1. In the J-Web application, select Configure > Setup Wizard. The Setup wizard opens on your screen.

Figure 6: Setup Wizard Page

2. Select Standard.

3. Configure the device and users:

a. Enter the hostname.

b. (Optional) Allow root access.

c. Enter the root authentication password.

d. (Optional) Add user accounts.

e. Click Next.

4. Set the time and configure the DNS server:

Otros manuales para SRX380

Tabla de contenidos

Otros manuales de Puerta de Juniper

Juniper

Juniper SRX 210 Instrucciones de instalación

Juniper

Juniper SRX240 Series Manual de usuario

Juniper

Juniper SRX5600 Manual de instrucciones

Juniper

Juniper SRX1500 Guía de configuración

Juniper

Juniper SRX100 Manual de usuario

Juniper

Juniper SRX4100 Instrucciones de instalación

Juniper

Juniper SRX 5800 Manual de instrucciones

Juniper

Juniper SSG140 Manual de usuario

Juniper

Juniper SRX240 Series Manual de usuario

Juniper

Juniper SRX240B Manual de usuario

Juniper

Juniper SRX5600 Instrucciones de instalación

Juniper

Juniper SRX4200 Guía de configuración

Juniper

Juniper SRX 5800 Manual de usuario

Juniper

Juniper SRX Series Manual de usuario

Juniper

Juniper SRX3600 Manual de usuario

Juniper

Juniper SRX110 Manual de usuario

Juniper

Juniper SRX550 Manual de usuario

Juniper

Juniper SRX5400 Manual de usuario

Juniper

Juniper SRX345 Manual de usuario

Juniper

Juniper SRX4100 Instrucciones de instalación

Juniper

Juniper SRX1500 Guía de configuración

Juniper

Juniper SRX 5800 Manual de usuario

Juniper

Juniper MAG2600 Instrucciones de instalación

Juniper

Juniper SRX650 Instrucciones de instalación

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario