Johnson Controls Tyco iSTAR Edge G2 Manual de usuario

iSTAR Edge G2 Controller

Quick Start Guide

March 2021

Revision: B0

www.swhouse.com

Document Number:8200-1917-01

C•CURE and Software House are registered trademarks of Johnson Controls.

The trademarks, logos, and service marks displayed on this document are registered in the United States [or other

countries]. Any misuse of the trademarks is strictly prohibited. All trademarks not owned by Johnson Controls are the

property of their respective owners, and are used with permission or allowed under applicable laws.

Products offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all

products include all features. Availability varies by region; contact your regional sales manager.

This manual is proprietary information of Software House. Unauthorized reproduction of any portion of this manual is

prohibited. The material in this manual is for information purposes only. It is subject to change without notice. Software

House assumes no responsibility for incorrect information this manual may contain.

Overview

The iSTAR Edge G2 Controller is supported on C•CURE 9000 version 2.80 and later with firmware version 6.8.x.

UL Listed Models

Part Number Description

GSTAR004 iSTAR Edge G2, 4 readers, in metal enclosure

GSTAR004-MB iSTAR Edge G2, 4 readers, board only

GSTAR004-MBP iSTAR Edge G2, 4 readers, board only w/PoE

GSTAR004-POE iSTAR Edge G2, 4 readers, metal encl, PoE+

GSTAR004-RM iSTAR Edge G2, 4 readers, metal encl, with 2 RM-4

Table 1:iSTAR and Components Wiring Specifications

NOTE • All controllers and networking equipment in a cluster must be UL listed to qualify as UL Listed

Products.

• USB has not been evaluated by UL.

• iSTAR Edge LCD display, and associated diagnostic tests, have not been evaluated by UL.

Compatible Readers

■RM2L-PI

■RM1 series

■RM2 series

■RM3 series

■RM2L-4000

■SWH-4200, SWH-4000, SWH-2100, SWH-3100, SWH-4100, SWH-5100, P345MTR, SWH-5200, P345KPMTR

■Touchscreen card reader

■OSDP-formatted readers

NOTE iClass and Mifare credential formats are not evaluated by UL.

Specifications and Requirements

Specifications

iSTAR Edge G2 Specifications

Environmental

Operational Temperature 32° F (0° C) to 120° F (49° C)

Electrical

Power 12 VDC, 5 A max

24 VDC, 5 A max

PoE, PoE+ (PoE/PoE+ module must be set to 24 V)

Auxiliary Power 12 VDC, 350mA

Wiegand Ports 12 VDC, 750 mA max each

Reader Output control

(red, green, yellow, beeper)

Open drain

10 mA max

Reader Input Lines (D0, D1) Low Level <0.8 V

High Level 4.0 - 5.25 V

Reader Output Voltage 12 VDC

RM / RS485 Reader Ports 12 VDC, 1.2 A each

Relay Ports 30 VDC, 3.0 A (Dry)

12/24 VDC, 750mA (Wet) Voltage is same as source voltage minus current

switch drop.

All outputs are Class 2 power limited.

Total port output limited by overall board maximum (5A minus board electronics).

Maximum loading must not exceed 4.5 A.

Table 2:Environmental and Electrical Specifications

Power

The iSTAR Edge G2 is powered by a UL 603 or UL 2610 External Power Supply, such as the Software House apS or a

Power over Ethernet (PoE) injector with a UL listed surge protector, evaluated to UL 1449.

A PoE module can be used with the following injectors:

■POE125U-4-HP-R

■POE36U-1AT-R

NOTE Phihong injectors , or power-limited, PoE injectors, which are UL 294 listed.

Ensure PoE/PoE+ modules are set to 24 V.

IEEE 802.3 (AT or AF) compliance was not verified to UL294.

PoE installations are UL listed for Mode B only.

Grounding Requirements

■Ensure that the iSTAR Edge G2 controller is properly connected to an earth ground at the ground stud in the cabinet.

Use 16 AWG or larger wire.

■Ensure that the shield wires for the readers, inputs, outputs, and AUX cables are grounded to the nearest ground

connection at one end only of the cable.

■Disconnect the ground wire last to provide maximum protection to the equipment and personnel.

Compliance

■The iSTAR Edge G2 must be installed within the protected premises.

■When purchased separately, the iSTAR Edge G2 modules must be installed in an enclosure which has an electrically

supervised tamper switch to maintain UL compliance.

■For Proprietary Burglar Alarm installations, the iSTAR Edge G2 must be installed in accordance with UL 681 -

Standard for Installation and Classification of Burglar and Hold-Up Alarm Systems.

Feature Level

Destructive Attack 1

Line Security 4

Endurance 4

Standby Power 1

Table 3:UL294 Levels

Safety Information

Life Safety Requirement

A fail-safe mechanism override must be installed at each card reader exit to allow people to leave the secure area in case of

electromechanical device failure.

Static Electricity

■Before handling any internal components, discharge static electricity by touching a grounded surface.

■Wear a grounding wrist strap and stand on a grounded static protection mat during installation

■Limit movement during installation to reduce static buildup.

■Transport components in static-shielded containers.

Ethernet Connection

■x2 Ethernet port onboard - supports 10/100/1000 Base-T Ethernet connections.

Communications

■Full 256-bit encryption.

NOTE All cabling must be shielded.

Installation

Mounting the Enclosure

The iSTAR Edge G2 module must be installed in a GSTAR-CAN to maintain UL listing.

NOTE The system must be installed indoors within a protected premises in accordance with the National Electrical Code (NFPA70), and

relevant local authority regulations.

1. Ensure that the mounting site has been prepared. A certified installer or structural engineer should verify the upper

mounting points.

2. Unpack the components while observing static electricity precautions.

3. Remove the appropriate knockouts for all of the wiring inputs and outputs.

4. Remove the enclosure door and place it on a soft surface.

5. Align the keyhole mounting slots at the upper back of the enclosure with the two upper mounting screws and lower the

enclosure into position. See iSTAR Edge G2 Enclosure on Page 7.

6. Install the two bottom mounting screws.

7. Attach conduit couplings to the knockout openings as needed to comply with local and national codes or regulations.

8. Reattach the enclosure door.

• If an accessory board is mounted to the inside of the door, ensure the wires are not pinched by the door.

• The iSTAR Edge G2 must be permanently wired to mains electricity without switches that could be used to

interrupt the electricity supply.

Figure 1:iSTAR Edge G2 Enclosure

NOTE The WIFI/BLE MODULE *PHASE 2* shown in Figure 1 is a future option which may not be included on your current iSTAR Edge G2

board.

Wiring

Wiring Specifications and Components

Signal From To AWG Shield Max Length

RS-485 Comm,

two wire

iSTAR Edge

RM and I/O

Modules

22 Yes 4000 ft (1212m)

Power iSTAR Edge

RM and I/O

Modules

22/18 No Range of 600 ft to

1500 ft, depending on

AWG used.

RJ-45-Ethernet iSTAR Edge

Hub, Host Cat 5e

N/A 328 ft (100m)

Supervised Input iSTAR Edge

Input 22/18 No 2000 ft (606m)

Request-to-exit

(REX or RTE)

iSTAR Edge

Switch 22/18 No 2000 ft (606m)

Door Contact (DSM) iSTAR Edge

Contact 22/18 No 2000 ft (606m)

Supervised Input iSTAR Edge

Input 22 Yes 2000 ft (606m)

Reader Input iSTAR Edge

Proximity/Wiegand

signaling read

head

Yes 200 ft (60.96m)

300 ft (91.4m)

500 ft (152.4m)

Table 4:iSTAR and Components Wiring Specifications

■There are 2 jumpers on the PoE module:

• x1 jumper to select PoE or PoE Plus (+). Ensure the jumpers are set correctly if using PoE.

• x1 jumper to configure the voltage used to power the Edge G2 and to supply the wet relays for door locks. Set the

jumper to 24 VDC for the Edge G2.

■Do not connect the PoE injector to a receptacle controlled by a switch.

■The Tamper, Battery Low, and AC Power Fail inputs must be enabled and connected to report to comply with UL

requirements.

NOTE Shielded cable must be used for AC Fail in Low Battery input connections.

Supervised Inputs must use shielded, 22 AWG (minimum) stranded, twisted-pair cable, such as Belden 9462 or equivalent, for

monitor points, DSMs, and REXs.

Wiring methods must be in accordance with the National Electrical Code, ANSI/NFPA 70.

Connections between PSE or power injector and the PD must use 26 AWG (0.13mm2) for patch cords and 24 AWG (0.21mm2) for

horizontal or riser cables connected through standard 8-pin RJ-45 connectors.

NO/NC Double Resistor 1K

This is the standard Software House method of supervision.

1K Ω is considered Secure and 500 Ω or 2K Ω are considered Alert. The wiring for NO and NC is different, as shown in

Figure 2.

Figure 2:NO / NC Double Resistor 1K

The NO/NC Double Resistor method will report:

■Short

■Normal / Secure (1K)

■Alert (500 Ω or 2K)

■Open (>30K)

■Line Fault (Any unexpected value). This is usually due to faulty resistors or incorrect resistor values.

Otros manuales para tyco iSTAR Edge G2

Tabla de contenidos

Otros manuales de Controladores de Johnson Controls

Johnson Controls

Johnson Controls M9316-A Z Series Manual de usuario

Johnson Controls

Johnson Controls M9320-AUA-4 Manual de usuario

Johnson Controls

Johnson Controls P2000 Manual

Johnson Controls

Johnson Controls VG1600 Series Manual de usuario

Johnson Controls

Johnson Controls FX-PCV1615 Manual de usuario

Johnson Controls

Johnson Controls tyco PowerSeries Neo Manual de usuario

Johnson Controls

Johnson Controls TEC3010 Manual de usuario

Johnson Controls

Johnson Controls Metasys VMA1610 Manual de usuario

Johnson Controls

Johnson Controls VA9204-B-2 Series Manual de usuario

Johnson Controls

Johnson Controls A28 Series Manual de usuario

Johnson Controls

Johnson Controls TRUE RH HC-67x3 Manual de usuario

Johnson Controls

Johnson Controls Metasys FEC Series Manual de usuario

Johnson Controls

Johnson Controls LN-DSWSC1-0 Manual de usuario

Johnson Controls

Johnson Controls ATC1510 Manual de usuario

Johnson Controls

Johnson Controls EDA-8102 Manual de usuario

Johnson Controls

Johnson Controls LN Series Manual de usuario

Johnson Controls

Johnson Controls M9220-GG-3 Series Manual de usuario

Johnson Controls

Johnson Controls VFD66 Series Manual

Johnson Controls

Johnson Controls FX-PCG1621 Series Manual de usuario

Johnson Controls

Johnson Controls VFD66 Series Manual de usuario

Johnson Controls

Johnson Controls LP-NRM653-000C Manual de usuario

Johnson Controls

Johnson Controls Joventa BAS1(S) Manual de usuario

Johnson Controls

Johnson Controls Tyco Kantech KT-400 Manual de usuario

Johnson Controls

Johnson Controls EDA-8100 Instrucciones de montaje

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

Johnson Controls tyco iSTAR Edge G2 Manual de usuario

Manuales populares de Controladores de otras marcas