JLG 260MRT Manual de usuario

October, 2012

260MRT,

3369LE, 4069LE

3394RT, 4394RT Scissor

Platform Control Measures

2.6.5 Duplicate controls: Location, accessibility, protection and selection

Duplicate controls for all powered functions that are necessary to retrieve the platform in an emergency shall be provided at the

base or ground level, and shall override control devices situated on the work platform.

Extracts from ASNZS 1418-10 2011

2.6.4 Work platform controls: Location, accessibility, protection

Control devices shall be situated on the work platform and shall be readily accessible to the operator. Platform control boxes not permanently

attached shall have their normal location and orientation clearly marked on the platform and the control box.

When released, all control devices shall automatically return to the ‘off’ or ‘neutral’ position, if used to control any movement of the MEWP.

All control devices shall be protected against activation other than that initiated by the operator.

NOTE: A separate control, which has to be continuously activated by the operator in order for any motion to take place, meets this

requirement.

Where a separate control is integral with a motion control, the control shall be mechanically protected against inadvertent actuation.

A guard shall be provided and located at least 50 mm above the highest point of the controls.

2.6.10 Overriding emergency system

Overriding of the platform emergency stop control and load-sensing system is allowed for rescuing a trapped or incapacitated operator on the

platform. Overriding is permitted only by the use of a safety device that is independent from the selection control device. The safety device shall be

operated by hold to run controls.

The overriding of the load-sensing system shall allow motion of the platform sufficient to rescue the operator. Features shall be provided to protect

against misuse of the overriding system.

Refer to the JLG operating manual for the Scissorlift .

Download operators manuals from:

www.jlg.com.au >Product Manuals>JLG > JLG Scissorlifts>

Control Measure

260MRT

M/3369LE

M/4069LE

3394RT

4394RT

Platform Emergency Stop switch, RED

Yes

Mechanical guarding at controls

Yes

Controls >50mm below the guard rails

Yes

Trigger switch as enable switch

Yes

Inactivity Timer on trigger switch

Yes 3 seconds

Yes 5 seconds

Interlock to prevent operation if joystick or

function switch activated before release of

RED emergency stop switch

Yes

Proportional lift/lower

Yes Lift/Lower No

Yes proportional

Lift/Lower No

Yes proportional

Lift/Lower No

Yes, lift & lower

proportional

Yes, lift & lower

proportional

Proportional drive

Yes

Start-up system test

Yes

Lift /drive Function selector switch,

momentary or maintained.

Momentary 3

seconds

Momentary3

seconds

Momentary 3

seconds

Momentary, 5

seconds

Momentary 5

seconds

Outdoor use Permitted

Yes, 2 person

Yes 6 person

Level sensor

Yes, 5 x 5 stowed

( 6 degree on special

extended outrigger

option)

Yes, 5 x 5 stowed

Out of Level Sensor cutout

Lift and elevated

drive

Lift and elevated

drive, 3 degree side

to side at full height

Lift and elevated

drive, 3 degree side

to side at full height

Lift and elevated

drive, 3 degree

side to side at full

height

Lift and elevated

drive, 3 degree side

to side at full height

Drive at full elevation

Yes

Optional on M4069

with outriggers and

All Wheel Drive.

Yes

ASNZS1418-10 2011 post May 2011 model.

Load Sensing System installed

Yes LSS

Ground controls override the platform

controls and override LSS in emergency

Yes

Ground controls include Emergency RED

stop switch

Yes

Manual bleed down valve at base

Yes, pull cable

Outrigger interlocks, prevent outrigger

function when scissor elevated

Interlocks active

Auto level Stabiliser function

Yes

Oscillating axle interlocks, lock axle when

elevated

No Oscillating axle

Interlocks Active

Motion Alarm

Yes

Strobe light at base

Yes

260MRT Diesel engine Scissorlift

Mechanical protection:

Joystick controller protected by

external metal guard over the control

box.

Platform control Box mounted on front

rail.

Control System:

Red Emergency switch shuts down all

platform functions.

Drive and lift momentary selector

switch allows either drive or lift.

Operator to select.

Joystick activation without the trigger

switch will prevent movement.

Trigger switch times out after 3 second

inactivity to prevent misuse.

Joystick proportional function requires

trigger switch to be activated before

moving joystick.

M/3369LE & M/4069LE Hybrid scissor lift

Mechanical protection:

Joystick controller protected by

external metal guard over the control

box.

Platform control Box mounted on front

rail.

Control System:

Red Emergency switch shuts down all

platform functions.

Drive and lift momentary selector

switch allows either drive or lift.

Operator to select.

Joystick activation without the trigger

switch will prevent movement.

Trigger switch times out after 3 second

inactivity to prevent misuse.

Joystick proportional function requires

trigger switch to be activated before

moving joystick.

3369LE, M3369, 4069LE M4069

•NOTE: Travel speed will automatically be reduced to low drive when the platform is raised above the stowed position.

•For M4069 (AUS Full Drive Height Model), low drive speed is cut back to creep drive speed above 28 - 30 ft (8.5 - 9.1 m) up to

the maximum height of 40 ft (12.2 m).

•Controller (Joystick)

The Joystick controls four functions: drive, steer, lift and optional outriggers. The drive or the lift function switch must be

selected before operating the joystick. The controller is ‘ramped’ to allow variable speed

•Drive Select

When selected, the drive function will be active for 3 seconds.

The operator has 3 seconds to select the desired direction of travel.

•Lift /Lower

When selected, the lift function will be active for 3 seconds. The operator has 3 seconds to select the desired direction of

lift.

3394RT & 4394RT Diesel Scissor lift

Mechanical protection:

Joystick controller protected by

external metal guard over the control

box.

Platform control Box mounted on front

rail.

Control System:

Red Emergency switch shuts down all

platform functions.

Drive and lift momentary selector

switch allows either drive or lift.

Operator to select.

Joystick activation without the trigger

switch will prevent movement.

Trigger switch times out after 5 second

inactivity to prevent misuse.

Joystick proportional function requires

trigger switch to be activated before

moving joystick.

260MRT, 3394RT, 4394RT Auto leveling jacks

•Auto Leveling Jacks - (Optional) –

When depressed the light will illuminate on the indicator pad, enabling that function for 5 seconds. Moving the control

handle forward will lower the leveling jacks. Moving the control handle backward will raise the leveling jacks. Once the

machine is level the jacks will discontinue extending and the jack set light will turn on.

NOTE: After initial ground contact is made, the auto level function will pause 2-5 seconds and then begin to properly level

the machine. Once level, the tilt light on the platform control box will stop blinking.

•NOTE: There is an override feature on the Auto Leveling system that allows the operator to adjust (trim) the level of the

machine to the left or right when the platform is completely lowered. Use the following instructions to adjust the level of the

machine.

a. Select the leveling jack selection switch and

squeeze the trigger switch on the controller.

b. To adjust the leveling jacks to the left, activate the

switch on top of the controller to the left. To adjust

to the right, activate the switch on top of the controller

to the right. The leveling jack indicator light

or the side selected will be lit.

Otros manuales para 260MRT

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de elevación de JLG

JLG

JLG G5-18A Manual de usuario

JLG

JLG TOUCAN 861 Manual de usuario

JLG

JLG LiftPod FS60 Guía de instalación y uso

JLG

JLG G5-18A Manual de usuario

JLG

JLG Skytrak 6036 Manual de uso y cuidado

JLG

JLG 4108AN Manual de uso y cuidado

JLG

JLG T350 Guía de instalación y uso

JLG

JLG 1930ES Manual de usuario

JLG

JLG 400S Guía de instalación y uso

JLG

JLG 400S Manual de usuario

JLG

JLG E400A Narrow Manual de uso y cuidado

JLG

JLG 19AMI Manual de uso y cuidado

JLG

JLG E300AJ Manual de uso y cuidado

JLG

JLG 10msp Guía de instalación y uso

JLG

JLG AM Series Manual de uso y cuidado

JLG

JLG G6-42A Guía

JLG

JLG E450A Guía de instalación y uso

JLG

JLG 10msp Guía de instalación y uso

JLG

JLG 600A Manual de uso y cuidado

JLG

JLG 25AM Manual de uso y cuidado

JLG

JLG X430AJ Manual de uso y cuidado

JLG

JLG 3513PS Manual de uso y cuidado

JLG

JLG EcoLift50 Guía de instalación y uso

JLG

JLG 800A Manual de uso y cuidado

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario