JLG 330CRT Manual de usuario

Service & Maintenance Manual

Model

330CRT

400CRT

3121804

April 7, 2004

INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

3121804 – JLG Lift – a

SECTION A. INTRODUCTION - MAINTENANCE SAFETY

PRECAUTIONS

A.A GENERAL

This section contains the general safety precautions

which must be observed during maintenance of the

aerial platform. It is of utmost importance that main-

tenance personnel pay strict attention to these warn-

ings and precautions to avoid possible injury to

themselves or others, or damage to the equipment.

A maintenance program must be followed to ensure

that the machine is safe to operate.

MODIFICATION OF THE MACHINE WITHOUT CERTIFI-

CATION BY A RESPONSIBLE AUTHORITY THAT THE

MACHINE IS AT LEAST AS SAFE AS ORIGINALLY

MANUFACTURED, IS A SAFETY VIOLATION.

The specific precautions to be observed during

maintenance are inserted at the appropriate point in

the manual. These precautions are, for the most

part, those that apply when servicing hydraulic and

larger machine component parts.

Your safety, and that of others, is the first consider-

ation when engaging in the maintenance of equip-

ment. Always be conscious of weight. Never attempt

to move heavy parts without the aid of a mechanical

device. Do not allow heavy objects to rest in an

unstable position. When raising a portion of the

equipment, ensure that adequate support is pro-

vided.

SINCE THE MACHINE MANUFACTURER HAS NO

DIRECT CONTROL OVER THE FIELD INSPECTION

AND MAINTENANCE, SAFETY IN THIS AREA RESPON-

SIBILITY OF THE OWNER/OPERATOR.

A.B HYDRAULIC SYSTEM SAFETY

It should be noted that the machines hydraulic sys-

tems operate at extremely high potentially danger-

ous pressures. Every effort should be made to

relieve any system pressure prior to disconnecting

or removing any portion of the system.

Relieve system pressure by cycling the applicable

control several times with the engine stopped and

ignition on, to direct any line pressure back into the

reservoir. Pressure feed lines to system components

can then be disconnected with minimal fluid loss.

A.C MAINTENANCE

FAILURE TO COMPLY WITH SAFETY PRECAUTIONS

LISTED IN THIS SECTION MAY RESULT IN MACHINE

DAMAGE, PERSONNEL INJURY OR DEATH AND IS A

SAFETY VIOLATION.

• NO SMOKING IS MANDATORY. NEVER REFUEL DUR-

ING ELECTRICAL STORMS. ENSURE THAT FUEL CAP

IS CLOSED AND SECURE AT ALL OTHER TIMES.

• REMOVE ALL RINGS, WATCHES AND JEWELRY

WHEN PERFORMING ANY MAINTENANCE.

• DO NOT WEAR LONG HAIR UNRESTRAINED, OR

LOOSE-FITTING CLOTHING AND NECKTIES WHICH

ARE APT TO BECOME CAUGHT ON OR ENTANGLED

IN EQUIPMENT.

• OBSERVE AND OBEY ALL WARNINGS AND CAU-

TIONS ON MACHINE AND IN SERVICE MANUAL.

• KEEP OIL, GREASE, WATER, ETC. WIPED FROM

STANDING SURFACES AND HAND HOLDS.

• USE CAUTION WHEN CHECKING A HOT, PRESSUR-

IZED COOLANT SYSTEM.

• NEVER WORK UNDER AN ELEVATED BOOM UNTIL

BOOM HAS BEEN SAFELY RESTRAINED FROM ANY

MOVEMENT BY BLOCKING OR OVERHEAD SLING,

OR BOOM SAFETY PROP HAS BEEN ENGAGED.

• BEFORE MAKING ADJUSTMENTS, LUBRICATING OR

PERFORMING ANY OTHER MAINTENANCE, SHUT

OFF ALL POWER CONTROLS.

• BATTERY SHOULD ALWAYS BE DISCONNECTED

DURING REPLACEMENT OF ELECTRICAL COMPO-

NENTS.

• KEEP ALL SUPPORT EQUIPMENT AND ATTACH-

MENTS STOWED IN THEIR PROPER PLACE.

• USE ONLY APPROVED, NONFLAMMABLE CLEANING

SOLVENTS.

INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

b–JLG Lift –3121804

REVISON LOG

Original Issue - April 13, 2000

Revised - August 17, 2000

Revised - September 28, 2001

Revised - October 18, 2002

Revised - April 7, 2004

TABLE OF CONTENTS

3121804 –JLG Lift –i

TABLE OF CONTENTS

SUBJECT - SECTION, PARAGRAPH PAGE NO.

SECTION A - INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

A.A General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-a

A.B Hydraulic System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-a

A.C Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-a

SECTION 1 - SPECIFICATIONS

1.1 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.2 Component Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.3 Performance Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.4 Torque Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.5 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.6 Pressure Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.7 Serial Number Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.8 Limit Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.9 Cylinder Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1.10 Major Component Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1.11 Critical Stability Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

SECTION 2 - PROCEDURES

2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2 Servicing and Maintenance Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

2.3 Lubrication Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2.4 Cylinders - Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2.5 Valves - Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2.6 Component Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.7 Wear Pads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.8 Cylinder Checking Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.9 Lift Cylinder Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2.10 Lift Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2.11 Steer Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

2.12 Oscillation Cylinder Bleeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2.13 Magnetic Speed Pickup Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2.14 Pressure Setting Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

2.15 Limit Switch Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

2.16 Automatic Choke - Field Adjustment (DF-750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

2.17 Electronic Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

2.18 Flash Codes and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

2.19 Preventive Maintenance and Inspection Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27

SECTION 3 - TROUBLESHOOTING

3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 Troubleshooting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.3 Hydraulic Circuit Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

TABLE OF CONTENTS

ii –JLG Lift –3121804

LIST OF FIGURES

FIGURE NO. TITLE PAGE NO.

1-1. Lubrication Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1-1. Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1-2. Serial Number Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

2-1. Arms and Platform Positioning and Support, Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

2-2. 330CRT Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7

2-3. 400CRT LIft Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

2-4. Cylinder Barrel Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2-5. Capscrew Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

2-6. Cylinder Rod Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2-7. Tapered Bushing Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

2-8. Rod Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

2-9. Wiper Seal Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11

2-10. Installation of Head Seal Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

2-11. Piston Seal Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12

2-12. Tapered Bushing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12

2-13. Seating the Tapered Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

2-14. Poly-Pak Piston Seal Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

2-15. Rod Assembly Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13

2-16. Steer Cylinder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

2-17. Magnetic Speed Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2-18. Magnetic Speed Pickup Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-16

2-19. Valve Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

2-20. Automatic Choke Adjustment (DF-750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-18

2-21. Analyzer Flow Chart - Sheet 1 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23

2-22. Analyzer Flow Chart - Sheet 2 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24

3-1. Electrical Schematic - Sheet 1 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10

3-2. Electrical Schematic - Sheet 2 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

3-3. Hydraulic Schematic - Sheet 1 of 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

3-4. Hydraulic Schematic - Sheet 2 of 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

TABLE OF CONTENTS

3121804 –JLG Lift –iii

LIST OF TABLES

TABLE NO. TITLE PAGE NO.

1-1 Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1-2 Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1-3 Lubrication Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1-4 Cylinder Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-5 Major Component Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-6 Critical Stability Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

2-1 Cylinder Component Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

2-2 Holding Valve Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

2-3 Help Messages and Flash Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

2-4 Machine Model Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

2-5 Machine Configuration Programming Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26

2-6 Preventive Maintenance and Safety Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

3-1 Elevation System Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3-2 Chassis Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

3-3 Hydraulic System Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

3-4 Electrical System Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

TABLE OF CONTENTS

iv –JLG Lift –3121804

This page left blank intentionally.

SECTION 1 - SPECIFICATIONS

3121804 –JLG Lift –1-1

SECTION 1. SPECIFICATIONS

1.1 CAPACITIES

Hydraulic Oil Tank

Approximately 60.6 liters (16 U.S. gallons) w/15% air

space

Hydraulic System (Including Tank)

Approximately 75.7 liters (20 U.S. gallons)

Fuel Tank

Approximately 48.8 liters (13 U.S. gallons)

Engine Crankcase

Gasoline Engine

3.2 liters (3.4 quarts) w/filter

2.7 liters (2.9 quarts) w/o filter

Diesel Engine

5.1 liters (5.4 quarts) w/filter

4.6 liters (4.9 quarts) w/o filter

Coolant Capacity

13.2 liters (3.5 U.S. gallons)

1.2 COMPONENT DATA

Gasoline Engine

Manufacturer - Kubota 750 Dual Fuel

Displacement - 750 cc

Low RPM - 2200

High RPM - 3600

Alternator - 40 Amp external

Battery - 85 Amphour, 700 cold cranking amps @ -17.8°C

(0° F)

Fuel Consumption

Low RPM - 4.9 lph (1.3 gph)

High RPM - 9 lph (2.4 gph)

Horsepower - 24.5 @ 3600 RPM

Diesel Engine

Manufacturer - Kubota 1105

Low RPM - 1500

High RPM - 3000

Alternator - 40 Amp

Battery - 85 Amphour, 700 cold cranking amps @ -17.8°C

(0° F)

Fuel Consumption

Low RPM - 3.5 lph (.93 gph)

High RPM - 6.6 lph (1.7 gph)

21 kW @ 3000 RPM (28 Horsepower @ 3000 RPM)

Drive/Steer System

Toe-In - Adjust to 12.7 mm (1/2 inch) overall

Drive Motor Displacement- 400 cc

Drive Brake - Spring applied, hydraulic release, release

pressure - 20.7 bar (300 psi ) max.

Hydraulic Filter - Full flow paper ( Cartridge type)

10 Microns Nominal

Tires

Standard 30.4 x 10 loader pneumatic or foam filled

NOTE: Inflate pnuematic tire to 3.1 bar (45 psi )

1.3 PERFORMANCE DATA

Travel Speed

High drive - 5.6 kmh (3.5 mph)

Gradeability

35%

Turning Radius (Inside)

7 ft. (2 m)

Lift Speed

Lift up - 330CRT - 36-40 seconds

400CRT - 53-55 seconds

Lift down - 330CRT - 36-40 seconds

400CRT - 49-51 seconds

SECTION 1 - SPECIFICATIONS

1-2 –JLG Lift –3121804

Platform Capacity

330CRT - 450 kg (1,000 lb.)

400 CRT - 360 kg (800 lb.)

Platform Extension Capacity

All Models - 120 kg (250 lb)

Machine Weight

330CRT - Approx. 4,409 kg (9,720 lb.)

440CRT - Approx. 5,601 kg (12,348 lb.)

Machine Platform Height (Fully Extended)

330 CRT - 10 m (33 ft.)

400 CRT - 12 m (40 ft.)

Machine Platform Height (Platform Lowered)

330 CRT - 1.7 m (66.5 in.)

400 CRT - 1.7 m (68.25 in.)

Machine Length

3 m (10 ft. 2 in.)

Machine Width

1.8 m (69 in.)

1.4 TORQUE REQUIREMENTS

All wheel lugs must be torqued at 142 Nm (105 ft lb) every

50 hours.

1.5 LUBRICATION

NOTE: Hydraulic oils must have anti-wear qualities at least

to API Service Classification GL-3, and sufficient

chemical stability for mobile hydraulic system ser-

vice. JLG Industries recommends Mobilfluid 424

hydraulic oil, which has an SAE viscosity index

of152.

NOTE: Aside from JLG recommendations, it is not advisable

to mix oils of different brands or types, as they may

not contain the same required additives or be of

comparable viscosities. If use of hydraulic oil other

than Mobilfluid 424 is desired, contact JLG Indus-

tries for proper recommendations.

Lubrication Specifications

Ta b l e 1 - 1 . H y d r a u l i c O i l

HYDRAULICSYSTEMOPERATING

TEMPERATURE RANGE

SAE VISCOSITY GRADE

0 to +23 degrees F

(-18 to -5 degrees C)

10W

0 to +210 degrees F

(-18 to +100 degrees C)

10W-20,10W-30

+50 to +210 degrees F

(+10 to +100 degrees C)

20W-20

Table 1-2. Lubrication Specifications

KEY SPECIFICATIONS

MPG Multipurpose Grease having a minimum dripping

point of 350 degrees F. Excellent water resistance

and adhesive qualities, and being of extreme pres-

sure type. (Timken OK 40 pounds minimum.)

EPGL Extreme Pressure Gear Lube (oil) meeting API ser-

vice classification GL-5 or MIL-Spec MIL-L-2105.

EO Engine (crankcase) Oil. Gas - API SF/SG class, MIL-

L-2104. Diesel - API CC/CD class, MIL-L-2104B/

MIL-L-2104C.

HO Hydraulic Oil. API service classification GL-3, e.g.

Mobil 424.

Otros manuales para 330CRT

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de elevación de JLG

JLG

JLG T350 Guía de instalación y uso

JLG

JLG 660SJ Guía de instalación y uso

JLG

JLG 1532E2 Guía de instalación y uso

JLG

JLG DVL Series Manual de uso y cuidado

JLG

JLG 600A Manual de uso y cuidado

JLG

JLG 400S Guía de instalación y uso

JLG

JLG X1000AJ Manual de uso y cuidado

JLG

JLG 1230ES Manual de uso y cuidado

JLG

JLG 800A Manual de uso y cuidado

JLG

JLG 4394RT Manual de uso y cuidado

JLG

JLG 1930ES Manual de usuario

JLG

JLG 1532E3 Manual de uso y cuidado

JLG

JLG 600SJC Guía de instalación y uso

JLG

JLG LiftPod FS80 Guía de instalación y uso

JLG

JLG EcoLift70 Manual de uso y cuidado

JLG

JLG 740AJ Guía de instalación y uso

JLG

JLG 400SJ Manual de uso y cuidado

JLG

JLG Toucan 12E Manual de uso y cuidado

JLG

JLG G6-42A Guía

JLG

JLG 10msp Manual de uso y cuidado

JLG

JLG 340AJ Manual de uso y cuidado

JLG

JLG 19AMI Manual de uso y cuidado

JLG

JLG 1230ES Guía de instalación y uso

JLG

JLG 3513PS Manual de uso y cuidado

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario