Jbc DI-2B Manual de usuario

Este manual sirve para los siguientes modelos

3

Tabla de contenidos

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

DI

1 tool

control unit

Reference Guide

www.jbctools.com

2

DI/1 TOOL CONTROL UNIT

DESOLDERING PUMP

MS-A

DESOLDERING STAND

DR-SA

CONTROL UNIT

DI-2B / DI-1B / DI-9B

Connectable tools: T210, T245, PA120, HT420, AP130, DR560 and DS360.

Connectable modules: MS, MV and MN.

CONTENTS

Power Cord Socket

USB Connector

to PC

JBC stations intelligently manage the tool temperature:

Work mode: When the tool is used, pre-set work temperature is 350º C.

Sleep mode: When the tool is in the stand, the temperature goes down to 220º C.

Hibernation mode: After longer periods of inactivity (pre-set i.e 30 minutes), the power is cut off and the

tool cools down to room temperature.

The advantage of this heat management is lifespan increase which ensure low cost of ownership

HEAT MANAGEMENT

DI

1 tool

control unit

Reference Guide

3

Main menu

Counters

Tool settings

Exit

1 Reset settings

2

Station settings

3

Tool settings

1

Plugged hours 0

2

Working hours 0

3

Sleep hours 0

1

Fix one temp -----

2

Temp levels set OFF

3

Sleep delay 0 min

4 Counters

5

Program version

4

Hibernation hours 0

5

No tool hours 0

6 Sleep cycles

0

7 Desold cycles

0

4

Sleep temp 220

0

C

5

Hibernation delay

3

0 min

6

Temp adjust O

O

C

Tool DR

Tool DR

Back

Back

0

c

Selected temp.

350

o

C

Power 10%

350

Decrease & move down Increase & move up

Tip temperature

% Instant power supplied to the tool

ORIGINAL PIN: 0105

Station settings

1 Temp unit

Celsius

2

Maximum temp 400

0

C

3

Minimum temp 200

0

C

4

Nitrogen mode OFF

5

Help text OFF

6 Beep ON

7 Power limit 130W

8

Change PIN

Back

Access Menu

&

Conﬁrm

Selection

WORKING

SETTINGS

WArrAntY

The JBC 2 years warranty, guarantees this equipment against all

manufacturing defects, covering the replacement of defective parts

and all necessary labour.

Warranty does not cover product wear due to use or mis-use.

In order for the warranty to be valid, equipment must be returned,

postage paid, to the dealer where it was purchased enclosing this,

fully ﬁlled in, sheet.

MORE INFORMATION

www.jbctools.com

SEriAl nº

StAMP oF DEAlEr

DAtE oF PurcHASE

0008528 / 0811

TECHNICAL SPECIFICATIONS

- Temperature selection from 90 to 450°C (±5%).

- Power: 75W.

- Safety transformer, mains separator and double isolation, with temperature protection fuse.

- DI-2B 230V control unit. Input: 230V 50/60Hz. Output: 24V.

- DI-1B 120V control unit. Input: 120V 50/60Hz. Output: 24V.

- DI-9B 100V control unit. Input: 100V 50/60Hz. Output: 24V.

- Total weight of unit: 2 Kg.

- Complies with CE standards on electrical safety, electromagnetic compatibility and ESD protected housing “skin

effect”.

- RoHS compliant.

- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.

This product should not be

thrown in the garbage.