Jason International MicroSilk Manual de usuario
Jason International, Inc. • 501.771.4477 Page 1 of 2 Customer Service : 800.255.5766
NOTE: These instructions can also be found in the
Installation, Operation and Maintenance manual of the
separately packaged MicroSilk®therapy bath unit.
WARNING: SYSTEM UNDER PRESSURE –
NEVER PERFORM MAINTENANCE WHILE SYSTEM
IS RUNNING.
MICROSILK®PUMP ASSEMBLY
Figure 1
The Jason MicroSilk®system has been factory assembled
following ETL and IAPMO guidelines. For shipping purposes,
the MicroSilk®Pump Assembly may be packaged separately
and disconnected from the bath.
Note: Verify the MicroSilk®Pump Assembly is the same
unit that was provided for the bath being installed. The serial
number listed on the label provided on the MicroSilk®Pump
Assembly carton should match the serial number of the bath.
WARNING: Any modification to the equipment is
not recommended and will VOID the manufacturer’s
warranty.
To install the MicroSilk®Pump Assembly to the bath, the
following procedures must be followed.
Note: Do not install the MicroSilk®Pump Assembly further
than the length of the tubing that is factory installed on the
bath. These tubing lengths have been designed for proper
drainage of the system.
1. Position the bath in the area of intended installation.
2. Before beginning any work, the installer is to determine
the proper location of the MicroSilk®Pump Assembly
and service access.
3. Do not disconnect the plumbing lines that are secured
to the bath with nylon tie straps (Figure 2).
INSTRUCTION MANUAL
MicroSilk®Pump Assembly
Field Installation
“TO BE REMOVED FOR USE BY THE OCCUPANT.”
49-2001-002
Date 11/14
Figure 2
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118
www.jasoninternational.com
MADE IN THE U.S.A.
Jason International, Inc. • 501.771.4477 Page 2 of 2 Customer Service : 800.255.5766
FIELD INSTALLATION INSTRUCTIONS (cont.)
Figure 3
7. For a MicroSilk®only or MicroSilk®-Air bath (not
MicroSilk®-Whirlpool), if an Automatic Ozone Sanitation
System is installed, connect the ozone system tubing to
the tee above the MicroSilk®Saturation Tank with the
included clamps (Figure 5).
Figure 5
8. The bottom of the Pump Mount must be secured and
level with the bottom of the bath. It is recommended
that removable fasteners be used in case any future
servicing is required.
9. Continue bath installation per the Jason Owner’s Manual
Installation, Operation, and Maintenance guide.
4. Clamp the MicroSilk®Jet Line to the MicroSilk®
Discharge Barb using the clamp provided on the tubing.
Assure the MicroSilk® Jet Line will allow proper drainage
to the Jets (Figure 3). The discharge hose must have a
continuous drop from the discharge barb to the jet fitting.
5. Clamp the MicroSilk®Suction Line to the MicroSilk®
Suction Barb using the clamp provided on the tubing.
Assure the MicroSilk®Suction Line will allow proper
drainage to the suction (Figure 4). The suction hose
must have a continuous drop from the suction barb to
the suction fitting.
Figure 4
6. Clamp the MicroSilk®Drain Line to the MicroSilk®Drain
Barb using the clamp provided on the tubing. Assure
the MicroSilk® Drain Line will allow proper drainage to
the drain fitting (Figure 4). The drain hose must have a
continuous drop from the drain barb to the drain fitting.
Caution: Confirm all tubing is fully engaged on its
respective barb and its clamp has secured the tubing
to the barb.
Otros manuales de Bañera de Jason International
Manuales populares de Bañera de otras marcas
Lyons
Lyons Elite ETLxx663219 Series Manual de usuario
Woodbridge
Woodbridge BJ500 Instrucciones de montaje
Whirlpool
Whirlpool Ariel ARL-702 Manual de usuario
TEIKO
TEIKO EXCELLENT DUO Manual de usuario
American Standard
American Standard Colony 5-1/2' x 32" Manual de usuario
American Standard
American Standard 3052OD.X0X Guía de inicio rápido
