IWILL P6NS Manual de usuario

EC Declaration of Conformity

Iwill Corp.

No. 9-1, Kong6th RD.,

Lin Kou 2nd Industrial

Park, Taipei, Taiwan R.O.C.

declare under sole responsibility that the

P6NS motherboard

meets the intent of Directive 89/336/ECC for Electromagnetic

Compatibility. Compliance was demonstrated to the following

specifications as listed in the official Journal of the European

Communities:

EN 50081-1 Emissions:

EN 55022 Radiated, Class B

EN 55022 Conducted, Class B

EN 60555-2 Power Harmonics

EN 50082-1 Immunity:

IEC 801-2 Electrostatic Discharge

IEC 801-3 RF Radiat

IEC 801-4 Fast Transient

About This Manual

This P6NS PPro SCSI Motherboard is the newest memberto our SCSI

Motherboard solution products families. It incorporated with new Intel generation

82440FX Chipset and with Adaptecnew Ultra / Ultra Wide SCSI embedded

which is equilevent to AHA 2940UW. AdaptecRAID port option ready is a big

advantagein this P6NS PPro SCSI motherboard.It can turn this SCSI

motherboard to supporthardwareSCSI RAID by addingthe RAIDBUS 1000 or

the ARO 1130 adapterfrom Adaptec.

This SCSI motherboard incorporated with Intel new 440FX Chipset which is PCI

Rev. 2.1 Compliant and supportwide range of the DRAMs include Fast Page,

EDO , Burst EDO DRAM type with SIMM socket. With 6 SIMM sockets

available,it is very flexible for customerto configure the system memory from

8MB up to 512MB.

Run with the new Intel Pentium Pro based CPU is the most important feature that

this motherboard provide.It support Intel Pentium Pro from 133Mhzup to

233Mhz.

Featurewith Error Check Correction ( ECC ) system memory is anotherplus on

this P6NS PPro SCSI Motherboard to outperform the whole system stability. It

equip 4 of the 72 Pin SIMM that support Fast Page, EDO or BEDO DRAM with

ECC.

This manualis subject to changewithout notice.

Trademark

Intel

/ Pentium is trade mark of Intel

Corporation and all otherproduct

namesaretrademarksand registered trademarksof their respective owners.

iii

Contents

Chapter 1 - Overview

1.1 Features........................................................... P1

Chapter 2 - Quick Installation ........................................ P5

Chapter 3 - Hardware Installation

3.1 Prepare & Inspection ....................................... P7

3.2 Placement ........................................................ P8

3.3 Block Diagram ................................................. P12

3.4 CPU group ...................................................... P13

3.5 Integrated PCI Bridge ...................................... P15

3.6 SCSI Interface ................................................. P16

3.7 Adaptec RAIDport option ................................. P19

3.8 IDE Interface ................................................... P20

3.9 USB ............................................................... P21

3.10 Enhanced Multi-I/O .......................................... P21

3.11 Other .............................................................. P23

Chapter 4 - ATX Form-Factor Overview ..................... P26

Chapter 5 - Award BIOS SETUP

5.1 Main Menu ...................................................... P34

5.3 Standard CMOS Setup .................................... P37

5.3 BIOS Features Setup ...................................... P41

5.4 Chipset Features Setup ................................... P47

5.5 Power Management Setup ............................... P55

5.6 PNP/PCI Configuration .................................... P55

5.7 Integrated Peripherals ..................................... P62

5.8 Load Setup Defaults ......................................... P64

5.9 Change Supervisor or User password................ P64

5.10 IDE HDD Auto Detection ................................. P65

5.11 HDD Low Level Format ................................... P65

5.12 Save & Exit Setup ........................................... P65

5.13 Exit without saving .......................................... P65

CHAPTER1

Overview

Thank you for purchasing this P6NS PPro SCSI Motherboard. This operation

manualwill guide you to proper configure and install. It has an overview of the

engineer design and feature of this board.Also, this manualprovidesuseful

information foryour later upgradeor changethe configuration.Keep this, for

your futureneed.

1.1 Features

This P6NS PPro SCSI Motherboard is a high performance on IntelPentium

Pro system hardware based motherboard.Both quality and innovative design to

address the need of today’s market. With various out-put voltage for Pentium Pro

level CPU supported,64 bit Burst Bus DRAM, Built-in AdaptecWide/ Ultra

Wide SCSI(AHA-2940UW) and Plug & Play Super I/O, this motherboard brings

exceptionalprocessing power that could only be achieved by Mini-computer.

Incorporatingthe new emerging industrial standard PeripheralComponent

Interconnect (PCI) Local Bus together with the standard 16-bit Industrial

Standard Architecture (ISA), this motherboard dramatically boots system I/O

through for even the most demanding a pplication in today’s market. The

hardwaredimension is Full ATX form factorwith fourlayer design technology.

The IntelPentiumPro Processor is the 6th generation in the Intel386, Intel

486, and Pentium family of processors. The Pentium Pro Processor hasseveral

key featuressuch as 12-stage super pipeline architecture, Built-in 256KB/512KB

cache,Out of order execution, dynamicbranch prediction & speculative

execution and a pipestage time 33 percent less than the Pentium Processor, which

helps achieve a higher clock rate on any given Process. It will be super pipeline

for high clock speed from 150MHzup to 233MHz.The Pentium Pro Processor

was used to theDynamicExecution that is the combination of improved branch

prediction, speculativeexecution and data flowanalysis that enablesthe Pentium

Pro processor to deliver its superior performancefrom CPU architecture.

The Pentium Pro Processor is a 64 bit processor with RISC technology. It

requires 32-bit applications(like Microsoft Windows NT and OS/2) to optimize

its capabilities and performances.The Pentium Pro processor delivers best value

for businesses moving to 32-bit computingwhen using the 32-bit Operating

System and Applications.

◼CPU

Intel Pentium Pro Processor operating at 150 ~ 233 MHz with 387 ZIF

socket 8 is scalableto accept fasterProcessors in the future. The Pentium

Pro Processor is the next in the Intel386,Intel486,and Pentium family of

processor. The second Level Cache(L2), controller are some of the

componentsthat existed in the Pentium Pro Processor.

◼Memories

Supports up to 512 Mega Bytes DRAM(minimum of 8 MB) onboard(72

Pin SIMM x 4, and BIOS auto FP DRAM, EDO and Burst EDO DRAM

detection and configuration.

◼BIOS:

Award BIOS, on-screen "Plug & Play" setup forAdaptec SCSI, Enhanced

IDE, and Super multi-IO. Support Flash ROM ( This ROM provides

better upgrade ability for user to updatetheirBIOS data on the system

board,user can down-load newer version BIOS from Internet,BBS or get

the diskette file from your vender.

◼Expansion slots:

1 X 16-bits ISA slots.

X 32-bits PCI slots for PCI compatible add-on cards.(PCI#2 is

occupied by the Adaptec SCSI, it is flexible for your choose while you

install a prior or minor controller on this PCI bus.)

1 X RAID port bus slot

◼Ultra/ Ultra Wide SCSI interface:

Built in Adaptec PCI Ultra Wide SCSI ( AIC 7880chip ) which is

equilevent to Adaptec AHA-2940UW PCI SCSI controller.

Data transfer rate up to 40MB/Sec.

Complete software driver from Adaptec Inc., include EZ-SCSI for

DOS/Windows, 7800 Family Set Driver forNetware, Windows NT ,

OS/2 , SCO Unix ,

Unixware.

◼IDE functions:

Built in dualPCI Bus EIDE Channels.

Support ATAPI (AT Attachment Packet Interface)

◼USB interface (Universal SerialBus):

Plug and Play peripherals outside the box

Up to 12Mbit

Easy of use

◼Floppy Interface:

Support both 3 1/2"and 5 1/4" floppy disk drives and Tape Drive

(360K / 720K/ 1.2M / 1.44M / 2.88MB)

Enabled/Disable selectable from system BIOS

Non-Burst Mode DMA Option

Byte Data FIFO

ModeDriver (option)

◼Serial Port

Two high speed 16550UART serial port

Address changeableform system BIOS

ProgrammableBaud Rate Generator

◼Parallel Port:

IRQ selectable for IRQ5(278h), 7IRQ(378h) from system BIOS.

Standard mode--Compatiblewith IBM PC/AT Printer port

EPP Mode --Enhanced Parallel Port compatible(EPP) compatible

IEEE 1284

ECP Mode --Microsoft & Hewlett Packard Extended Capabilities Port

(ECP) Compatible

IncorporatesChip Protect Circuit for protection against damage due to

printer power-on

◼Others function:

Support both Fast Page DRAM or EDO DRAM SIMM.

Support Pentium CPU SMM (System Management Mode).

Using Embeded Battery in RTC (Real Time Clock) which provides

environmentalprotection and longer battery life.

◼Input Power supply

Supports AT and ATX power Supply Connectors.

Supports Power/ON Switch when ATX power Supply is plugged

◼Physical Dimension

Four Layerdesign technology and 245mm x 305mm fullATX form factor.

CHAPTER2

Quick Installation

This SCSIMotherboard isshippedwith

manufacturepresetat:

1. CPU Clock at 200 MHz

2. Adaptec Ultra Wide SCSI Chip Enabled

3. Wide SCSI Mode Enabled

4. SCSI Terminator Control by BIOS

5. Printer ECPMode at DMA3

6. Printer at IRQ7, Address at 378h

7. Serial 1 at IRQ4, Serial 2 at IRQ3

8. PS/2 MOUSE at IRQ 12

Referenceto the Chapter 3 & Chapter 4, if you

havedevices conflictwith themanufacturedefault.

Step 1. Install CPU and Cooler

Make sure the Clock Frequency is set to the sameas theCPU

installed.

Step 2. Install the memory

Plug at least 2 PCS of 72 pins Micro Edge DRAM modules.

Step 3. Install display controller and connect I/O ports

This system boardis designed using PCI (Peripheral Component

Interconnect)and ISA (Industry Standard Architecture) interface

controller. This support +5Volt interface slots. All PCI interface

controllers must be PCI Rev 2.1 compliant.

Step 4. Connect the power supply

Connect AT P8 and P9 or the ATX ( Recommended )from

power supply output.

Step 5. Power on the system

Turn on the Computerpower.( Make sure the volutage110 or

220 in your area )

Step 6. Setting up the system

Enter the "Setup Menu" screen by press the " Del " key while

power on or warm reset the system.Always "LOAD SETUP

DEFAULT" at first and select others necessary that your

system require.

Step 7. Save the setup data to the CMOS

Exit the "Setup Menu " screen and then write to CMOS RAM.

And enjoy the high performance system board.

Step 8. After boot yoursystem O.S., insert the AdaptecEZ-SCSI

Installation diskette in a floppy disk drive and follow the EZ-

SCSI operation manualorreference to Adaptec 7800 Family

Set manualwhich will guide you to install theDOS/Windows,

Netware, Windows NT, OS/2 , SCO UNIX, Unixware.

CHAPTER3

Hardware Installation

3.1 Preparation and Inspection

Tabla de contenidos

Otros manuales de Placa madre de IWILL

IWILL

IWILL FB24624100 Manual de usuario

IWILL

IWILL P4SP Manual de usuario

IWILL

IWILL IWILL P4D-N Manual de usuario

IWILL

IWILL wa133 Manual de usuario

IWILL

IWILL XP333 Manual de usuario

IWILL

IWILL P55XB2 Manual de usuario

IWILL

IWILL Motherboard DJ800 Manual de usuario

IWILL

IWILL KK266 Manual de usuario

IWILL

IWILL XA100 Ultra ATA-2 Manual de usuario

IWILL

IWILL kv200 Manual de usuario

IWILL

IWILL DK8X Manual de usuario

IWILL

IWILL P4DA Manual de usuario

IWILL

IWILL DN800-SATA Manual de usuario

IWILL

IWILL P55XPLUS Manual de usuario

IWILL

IWILL P55TV Manual de usuario

IWILL

IWILL P4R533 Manual de usuario

IWILL

IWILL DP533 Series Manual de usuario

IWILL

IWILL KK266plus-R Instrucciones de funcionamiento originales

IWILL

IWILL mp4s Instrucciones de funcionamiento originales

IWILL

IWILL DK8N Manual de usuario

IWILL

IWILL DH800 Manual de usuario

IWILL

IWILL UPX Manual de usuario

IWILL

IWILL DNS-SATA Manual de usuario

IWILL

IWILL MPX2 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario