Intermec ScanPlus 1800ST Manual de usuario
ScanPlus 1800ST
Scanner
Service Manual
Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203-9280
U.S. service and technical support: 1-800-755-5505
U.S. media supplies ordering information: 1-800-227-9947
Canadian service and technical support: 1-800-668-7043
Canadian media supplies ordering information: 1-800-268-6936
Outside U.S.A. and Canada: Contact your local Intermec service supplier.
The information contained herein is proprietary and is provided solely for the purpose of allowing customers
to operate and/or service Intermec manufactured equipment and is not to be released, reproduced, or used for
any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change without notice.
2001 by Intermec Technologies Corporation
All Rights Reserved
The word Intermec, the Intermec logo, INCA (under license), MobileLAN, JANUS, IRL, Trakker Antares,
EZBuilder, TE 2000, Data Collection Browser, dcBrowser, Universal Access Point, UAP, Duratherm,
EasyCoder, Precision Print, PrintSet, Virtual Wedge, and CrossBar are either trademarks or registered
trademarks of Intermec.
Throughout this manual, trademarked names may be used. Rather than put a trademark (or ) symbol in
every occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and
to the benefit of the trademark owner, with no intention of infringement.
There are U.S. and foreign patents pending.
Contents
iii
Contents
Before You Begin v
Warranty Information v
Safety Summary v
Warnings, Cautions, and Notes vi
About This Manual vi
Repairing the 1800
Cautions 1-3
Ordering Replacement Parts 1-3
Replacing Parts 1-4
Spare Parts List 1-4
Disconnecting the Cable 1-5
Opening the 1800 1-7
Assembling the 1800 1-8
Replacing the Top Shell Assembly 1-9
Replacing the Bottom Shell Assembly or Trigger Spring 1-9
Replacing the Exit Window or Front Rubber Enclosure 1-11
Replacing the Main PCB Assembly 1-13
Replacing the Laser Absorber, Buzzer Cap, or Laser Frame 1-15
Replacing the Scan Engine 1-18
Replacing the Connector PCB Assembly 1-20
Connecting the Cable 1-22
Testing and Upgrading the 1800
Testing the 1800 2-3
Test Conditions 2-3
Test Procedure 2-3
Test Parameters 2-5
Upgrading the 1800 Firmware 2-5
Upgrading the Smart Cable Firmware 2-6
1
2
Before You Begin
v
Before You Begin
This section introduces you to standard warranty provisions, safety precautions,
warnings and cautions.
Warranty Information
To receive a copy of the standard warranty provision for this product, contact your
local Intermec support services organization. In the U.S. call 1-800-755-5505, and in
Canada call 1-800-668-7043. If you live outside of the U.S. or Canada, you can find
your local Intermec support services organization on the Intermec Web site at
www.intermec.com.
Safety Summary
Your safety is extremely important. Read and follow all warnings and cautions in this
book before handling and operating Intermec equipment. You can be seriously injured,
and equipment and data can be damaged if you do not follow the safety warnings and
cautions.
Do not repair or adjust alone Do not repair or adjust energized equipment alone
under any circumstances. Someone capable of providing first aid must always be
present for your safety.
First aid Always obtain first aid or medical attention immediately after an injury.
Never neglect an injury, no matter how slight it seems.
Resuscitation Begin resuscitation immediately if someone is injured and stops
breathing. Any delay could result in death. To work on or near high voltage, you should
be familiar with approved industrial first aid methods.
Energized equipment Never work on energized equipment unless authorized by a
responsible authority. Energized electrical equipment is dangerous. Electrical shock
from energized equipment can cause death. If you must perform authorized emergency
work on energized equipment, be sure that you comply strictly with approved safety
regulations.
ScanPlus 1800ST Service Manual
vi
Warnings, Cautions, and Notes
The warnings, cautions, and notes in this manual use this format:
Warning
A warning alerts you of an operating procedure, practice, condition, or statement
that must be strictly observed to avoid death or serious injury to the persons
working on the equipment.
Caution
A caution alerts you to an operating procedure, practice, condition, or statement
that must be strictly observed to prevent equipment damage or destruction, or
corruption or loss of data.
Follow ESD
Procedures
Follow ESD Procedures
This icon appears at the beginning of any procedure in this manual that could
cause you to touch components (such as printed circuit boards) that are susceptible
to damage from electrostatic discharge (ESD). When you see this icon, you must
follow standard ESD guidelines to avoid damaging the equipment you are
servicing.
Note: Notes are statements that either provide extra information about a topic or
contain special instructions for handling a particular condition or set of circumstances.
Page 1-3 lists cautions you must follow before repairing the 1800 scanner.
About This Manual
This manual will help you troubleshoot and repair the 1800 scanner. It also explains
how to replace parts and shows the spare parts lists.
This manual is written for service technicians who will troubleshoot and repair the
1800 scanner.
Repairing the 1800
1
Repairing the 1800
1-3
1
This chapter explains how to open, assemble, and repair the ScanPlus 1800. It also
gives preliminary cautions to follow when servicing the 1800.
Cautions
Because finger oils can dissolve the reflective coating of the plastic mirrors, always
wear finger cots or non-powdered latex gloves when handling optical parts.
Caution
Always wear an anti-static bracelet when handling all PCB assemblies.
Caution
Never touch the optical surfaces of the mirror, reflector, or lenses, even when you are
wearing gloves.
Caution
Take all precautions to protect the plastic outer case from stains, marks, and
scratches.
ScanPlus 1800ST Service Manual
1-4
Replacing Parts
Thenext illustration showsthe parts of the 1800.
5
4
1
2
63
910
11
7
8
1800M001.eps
Spare Parts List
Description Callout
Number Part Number
Front rubber enclosure 13-360039-31
Exit window23-360039-31
Top shell assembly 33-360039-30
Trigger spring43-360039-31
Bottomshell assembly 53-360039-31
Scanengine63-360039-08
Laser absorber 73-360039-32
Laser frame83-360039-32
Buzzer cap 93-360039-32
MainPCB withlaser flex 10 3-360039-32
Connector PCB withconnector flex 11 3-360039-33
Otros manuales para ScanPlus 1800ST
1
Tabla de contenidos
Otros manuales de Escáner de Intermec
Intermec
Intermec MaxiScan 3300 Manual de usuario
Intermec
Intermec ScanPlus 1800ST Manual de usuario
Intermec
Intermec SG20B Manual de usuario
Intermec
Intermec 1550 Series Manual de usuario
Intermec
Intermec Trakker Antares 2420 Manual de usuario
Intermec
Intermec SR61T Manual de usuario
Intermec
Intermec SG20T Manual de usuario
Intermec
Intermec IV7 Manual de usuario
Intermec
Intermec SR61B Manual de usuario
Intermec
Intermec SF51 Manual de usuario
Intermec
Intermec MaxiScan 2200 Manual de usuario
Intermec
Intermec Sabre 1552 Scanner Guía del usuario
Intermec
Intermec MicroBar 9710 Manual de usuario
Intermec
Intermec SR30 Manual de usuario
Intermec
Intermec SE1022 Manual de usuario
Intermec
Intermec SG10T Manual de usuario
Intermec
Intermec MaxiScan 2210 Manual
Intermec
Intermec Sabre 1551C Manual de usuario
Intermec
Intermec Sabre 1517 Manual
Intermec
Intermec MaxiScan 3010 Manual de usuario
