Intempco CX600 Series Manual de usuario

InTemp® CX600 Dry Ice/CX700 Cryogenic Logger Manual

22025-G

InTemp CX600 Dry Ice and CX700 Cryogenic loggers are designed for cold shipment monitoring

and have a built-in external probe that can measure temperatures as low as -95°C (-139°F) for

the CX600 series or -200°C (-328°F) for the CX700 series. The loggers include a protecve

sheath to prevent cung the cable during shipment and a clip for mounng the probe.

Designed for wireless communicaon with a mobile device, these Bluetooth® Low Energy-

enabled loggers use the InTemp app, and InTempConnect® web-based soware to form the

InTemp temperature monitoring soluon. Using the InTemp app on your phone or tablet, you

can conﬁgure the loggers and then download them to share and view logger reports, which

include logged data, excursions, and alarm informaon. Or, you can use InTempConnect to

conﬁgure and download CX series loggers via the CX5000 Gateway. The InTempVerify™ app is

also available to easily download loggers and automacally upload reports to InTempConnect.

Once logged data is uploaded to InTempConnect, you can view logger conﬁguraons, build

custom reports, monitor trip informaon, and more. Both the CX600 and CX700 series loggers

are available in single-use 90-day models (CX602 and CX702) or mulple-use 365-day models

(CX603 or CX703).

Specications

Temperature ProbeCX602 & CX603 CX702 & CX703

Sensor Range -95° to 50°C (-139° to 122°F) -200° to 50°C (-328° to 122°F);

To ensure insulaon integrity,

avoid ﬂexing the wire during

exposure to temperatures below

-100°C (-148°F)

Accuracy ±1.5°C from -95° to -40°C (±2.7°F

from -139° to -40°F)

±1.0°C from -40° to -10°C (±1.8°F

from -40° to 14°F)

±0.5°C from -10° to 50°C (±0.9°F

from -14° to 122°F)

±1.5°C from -200° to -90°C (±2.7°F

from -328° to -130°F)

±1.0°C from -90° to -10°C (±1.8°F

from -328° to 14°F)

±0.5°C from -10° to 50°C (±0.9°F

from 14° to 122°F)

Resolution 0.013°C at 25°C (0.023°F at 77°F)

Drift <0.1°C (0.18°F) per year

NIST Calibration Three-point NIST calibraon,

probe only

CX702 and CX703: Single-point

NIST calibraon, probe only

CX703-UN: Calibraon not

included

Cable Length 1.5 m (4.92 )

Probe Dimensions Food-grade stainless steel probe with blunt p, 31.75 mm (1.25 inches)

long, 4.78 mm (0.188 inches) diameter

Logger

Logger Operating Range -30° to 50°C (-22° to 122°F)

Radio Power 1 mW (0 dBm)

Transmission Range Approximately 30.5 m (100 ) line-of-sight

Wireless Data Standard Bluetooth Low Energy (Bluetooth Smart)

Type CX602 and CX702: Single use

CX603, CX703, and CX703-UN: Mulple use

Duration CX602 and CX702: 90 days

CX603, CX703, and CX703-UN: Up to 1 year

Shelf Life Up to 1 year

Logging Rate 1 second to 18 hours

Time Accuracy ±1 minute per month at 25°C (77°F)

Battery CR2450 3V lithium, not replaceable. Baery for CX602 and CX702

models lasts for duraon speciﬁed when logger is used within the 1-year

shelf life. Baery life for the CX603 and CX703 models is 1 year, typical

with logging interval of 1 minute. Faster logging intervals, remaining

connected with the InTemp app, excessive downloads, and paging may

impact baery life.

(CX602 model shown)

InTemp CX600/CX700 and

Series Loggers

Models:

•CX602, 90-day logger,

single use

•CX603, 365-day logger,

mulple use

•CX702, 90-day logger,

single use

•CX703, 365-day logger,

mulple use

•CX703-UN, 365-day logger,

mulple use, without NIST

calibraon

Required Items:

•InTemp app

•Device with iOS or

Android™ and Bluetooth

All manuals and user guides at all-guides.com

InTemp CX600 Dry Ice/CX700 Cryogenic Logger Manual

www.prosensor.com2

Specications (continued)

Memory 16,000 measurements

Full Memory Download

Time

Approximately 30 seconds; may take longer the farther the device is

from the logger

Dimensions 6.9 x 4.5 x 1.1 cm (2.71 x 1.76 x 0.42 inches)

eight 25.5 g (0.90 oz)

Environmental Rating IP65

The CE Marking idenﬁes this product as complying with all relevant

direcves in the European Union (EU).

See last page

Passed RTCA DO160G, part 21H

Logger Components and Operation

Mounting Loop: Use this to e the logger to the materials being

monitored.

Duration: This number indicates how many days the logger will

last: 90 days for the CX602 and CX702 or 365 days for the

CX603 and CX703 models.

Alarm LED: This LED blinks red every 4 seconds when an alarm

is tripped. Both this LED and the status LED will blink once when

you press the start buon to wake up the logger before

conﬁguring it. If you select Page Logger LED in the InTemp app,

both LEDs will be illuminated for 4 seconds.

Status LED: This LED blinks green every 4 seconds when the

logger is logging. If the logger is waing to start logging

(because it was conﬁgured to start “On buon push,” “On

buon push with ﬁxed delay,” or with a delayed start), it will

blink green every 8 seconds.

Start Button:Press this buon for 1 second to wake up the

logger to begin using it. Once the logger is awake, press this

buon for 1 second to move it to the top of the loggers list in

the InTemp app. Press this buon for 4 seconds to start the

logger when it is conﬁgured to start “On buon push” or “On

buon push with ﬁxed delay.” Both LEDs will blink four mes

when you press the start buon to begin logging. You can also

press this buon to stop the logger when it is conﬁgured to

“Stop on buon push.”

Temperature Probe: This is the built-in external probe for

measuring temperature.

Getting Started

InTempConnect is web-based soware where you can monitor

CX600 and CX700 series logger conﬁguraons and view

downloaded data online. Using the InTemp app, you can

conﬁgure the logger with your phone or tablet and then

download reports, which are saved in the app and

automacally uploaded to InTempConnect. Or, anyone can

download a logger using the InTempVerify app if the loggers

are enabled to be used with InTempVerify. See

www.intempconnect.com/help for details on both the gateway

and InTempVerify. If you do not need to access logged data via

the cloud-based InTempConnect soware, then you also have

the opon to use the logger with the InTemp app only.

Follow these steps to begin using the loggers with

InTempConnect and the InTemp app.

1. Set up an InTempConnect account and create roles,

privileges, proles, and trip information elds. If you are

using the logger with the InTemp app only, skip to step 2.

a. Go to www.intempconnect.com and follow the prompts

to set up an administrator account. You’ll receive an

email to acvate the account.

b. Log into www.intempconnect.com and add roles for the

users you will be adding to the account. Click Sengs and

then Roles. Click Add Role, enter a descripon, select the

privileges for the role and click Save.

c. Click Sengs and then Users to add users to your

account. Click Add User enter the email address and ﬁrst

and last name of the user. Select the roles for the user

and click Save.

d. New users will receive an email to acvate their user

accounts.

e. Click Loggers and then Logger Proﬁles if you want to add

a custom proﬁle. (If you want to use the preset logger

proﬁles only, skip to step f.) Click Add Logger Proﬁle and

ﬁll out the ﬁelds. Click Save.

f. Click the Trip Informaon tab if you want to set up trip

informaon ﬁelds. Click Add Trip Info Field and ﬁll out the

ﬁelds. Click Save.

2. Download the InTemp app and log in.

a. Download InTemp to a phone or tablet from the App

Store® or Google Play™.

b. Open the app and enable Bluetooth in the device sengs

if prompted.

Duraon

Alarm LED

Status LED

Mounng

Loop

Start Buon

Temperature

Probe

All manuals and user guides at all-guides.com

InTemp CX600 Dry Ice/CX700 Cryogenic Logger Manual

www.prosensor.com3

c. InTempConnect users:Log in with your InTempConnect

user credenals. Make sure to check the box that says “I

am an InTempConnect user” when signing in.

InTemp app only users: If you will not be using

InTempConnect, create a user account and log in when

prompted. DO NOT check the box that says “I am an

InTempConnect user” when signing in.

3. Congure the logger.Note that InTempConnect users

require privileges for conﬁguring the logger.

Important: CX602 and CX702 loggers cannot be

restarted once logging begins. Do not connue with

these steps unl you are ready to use these loggers.

InTempConnect users: Conﬁguring the logger requires

privileges. Administrators or those with the required

privileges can also set up custom proﬁles and trip

informaon ﬁelds. This should be done before compleng

these steps. If you plan to use the logger with the

InTempVerify app, then you must create a logger proﬁle

with InTempVerify enabled. See

www.intempconnect.com/help for details.

InTemp App only users: The logger includes preset proﬁles.

To set up a custom proﬁle, tap the Sengs icon and tap

CX600 or CX700 Logger before compleng these steps.

a. Press the buon on the logger to wake it up.

b. Tap the Devices icon in the app. Find the logger in the list

and tap it to connect to it. If you are working with

mulple loggers, press the buon again to bring the

logger to the top of the list.

If you are having trouble connecng:

•Make sure the logger is within range of your mobile

device. The range for successful wireless

communicaon is approximately 30.5 m (100 ) with

full line-of-sight.

•If your device can connect to the logger intermiently

or loses its connecon, move closer to the logger,

within sight if possible.

•Change the orientaon of your phone or tablet to

ensure the antenna in your device is pointed toward

the logger. Obstacles between the antenna in the

device and the logger may result in intermient

connecons.

•If the logger appears in the list, but you cannot connect

to it, close the app, power down the mobile device,

and then turn it back on. This forces the previous

Bluetooth connecon to close.

c.Once connected, tap Conﬁgure. Swipe le and right to

select a logger proﬁle. Type a name or label for the

logger. Tap Start to load the selected proﬁle to the

logger. InTempConnect users: If trip informaon ﬁelds

were set up, you will be prompted to enter addional

informaon. Tap Start in the upper right corner when

done.

4. Deploy and start the logger.

Important: Reminder, CX601 and CX602 loggers cannot

be restarted once logging begins. Do not connue with

these steps unl you are ready to use these loggers.

a. Deploy the logger to the locaon where you will be

monitoring the temperature.

b. Press the buon on the logger when you want logging to

begin (or if you chose a custom proﬁle, logging will begin

based on the sengs in the proﬁle).

If the logger was conﬁgured with alarm sengs, an alarm will

trip when the temperature reading is outside the range

speciﬁed in the logger proﬁle. The logger alarm LED will blink

every 4 seconds, an alarm icon appears in the app, and an

Alarm Out of Range event is logged. You can review alarm

informaon in the logger report (see Downloading the Logger).

InTempConnect users can also receive noﬁcaons when an

alarm is tripped. See www.intempconnect.com/help for more

details on conﬁguring the logger and monitoring alarms.

Passkey Protection

The logger is protected by an encrypted passkey automacally

generated by the InTemp app for InTempConnect users and

oponally available if you are using the InTemp app only. The

passkey uses a proprietary encrypon algorithm that changes

with every connecon.

InTempConnect Users

Only InTempConnect users belonging to the same

InTempConnect account can connect to a logger once it is

conﬁgured. When an InTempConnect user ﬁrst conﬁgures a

logger, it is locked with an encrypted passkey that is

automacally generated by the InTemp app. Aer the logger is

conﬁgured, only acve users associated with that account will

be able to connect to it. If a user belongs to a diﬀerent account,

that user will not be able to connect to the logger with the

InTemp app, which will display an invalid passkey message.

Administrators or users with the required privileges can also

view the passkey from the device conﬁguraon page in

InTempConnect and share them if needed. See

www.intempconnect.com/help for more details. Note: This

does not apply to InTempVerify. if the logger was conﬁgured

with a logger proﬁle in which InTempVerify was enabled, then

anyone can download the logger with the InTempVerify app.

InTemp App Only Users

If you are using the InTemp app only (not logging in as an

InTempConnect user), you can create an encrypted passkey for

the logger that will be required if another phone or tablet

aempts to connect to it. This is recommended to ensure that

a deployed logger is not mistakenly stopped or purposely

altered by others.

To set a passkey:

1. Press the buon on the logger to wake it up.

2. Tap the Devices icon and connect to the logger.

All manuals and user guides at all-guides.com

InTemp CX600 Dry Ice/CX700 Cryogenic Logger Manual

www.prosensor.com4

3. Tap Set Logger Passkey.

4. Type a passkey up to 10 characters.

5. Tap Save.

6. Tap Disconnect.

Only the phone or tablet used to set the passkey can then

connect to the logger without entering a passkey; all other

mobile devices will be required to enter the passkey. For

example, if you set the passkey for the logger with your tablet

and then try to connect to the device later with your phone,

you will be required to enter the passkey on the phone but not

with your tablet. Similarly, if others aempt to connect to the

logger with diﬀerent devices, then they would also be required

to enter the passkey. To reset a passkey, connect to the logger,

tap Set Logger Passkey, and select Reset to Factory Default.

Downloading the Logger

You can download the logger to a phone or tablet and generate

reports that include logged data and alarm informaon.

Reports can be shared immediately upon download or accessed

later in the InTemp app.

InTempConnect users: Privileges are required to download,

preview, and share reports in the InTemp app. Report data is

automacally uploaded to InTempConnect when you download

the logger. Log in to InTempConnect to build custom reports

(requires privileges). In addion, InTempConnect users can also

download CX loggers automacally on a regular basis using the

CX5000 Gateway. Or, if the logger was conﬁgured with a logger

proﬁle in which InTempVerify was enabled, then anyone can

download the logger with the InTempVerify app. For details on

the gateway and InTempVerify, see www.intempconnect/help.

To download the logger with the InTemp app:

1. Press the buon on the logger to wake it up.

2. Tap the Devices icon and connect to the logger.

3. Tap Download.

4. Choose a download opon:

Important: CX602 and CX702 loggers cannot be

restarted. If you want a CX602 or CX702 logger to

connue logging aer the download is complete, select

Download & Connue.

•Download & Connue. The logger will connue logging

once the download is complete.

•Download & Restart (CX603 models only). The logger will

start a new data set using the same proﬁle once the

download is complete. Note that if the logger was

originally conﬁgured with a push buon start, you must

push the start buon for logging to restart.

•Download & Stop. The logger will stop logging once the

download is complete.

A report of the download is generated and is also uploaded to

InTempConnect if you are logged in to the InTemp app with

your InTempConnect user credenals.

In the app, tap Sengs to change the default report type

(Secure PDF or XLSX) and report sharing opons. The report is

also available in in both formats for sharing at a later me. Tap

the Reports icon to access previously downloaded reports. See

www.intempconnect.com/help for details on working with

reports in both the InTemp app and InTempConnect.

Logger Events

The logger records the following events to track logger

operaon and status. These events are listed in reports

downloaded from the logger.

Event Name Denition

Conﬁgured The logger was conﬁgured by a user.

Connected The logger was connected to the InTemp

app.

Started The logger started logging.

Stopped The logger stopped logging.

Downloaded The logger was downloaded.

Alarm Out of

Range/In Range

An alarm has occurred because the reading

was outside the alarm limits or back within

range. Note:Although the reading may

return to a normal range, the alarm

indicator will not clear in the InTemp app

and the alarm LED will connue to blink.

Safe Shutdown The baery level dropped below a safe

operang voltage and performed a safe

shutdown.

Deploying the Logger

Use the mounng loop on the logger to secure it to a shipment

or other applicaon you are monitoring. You can also remove

the backing on the tape that is adhered to the top and boom

of the logger to mount it on a ﬂat surface.

Place the stainless steel probe in the plasc clip included with

the logger and clip it to a box or other item.

The external probe cable has a protecve sheath. Move the

sheath as needed to posion it where the cable will be

protected during shipments from inadvertent cuts.

Protecting the Logger

Note: Static electricity may cause the logger to stop logging.

The logger has been tested to 8 KV, but avoid electrostac

discharge by grounding yourself to protect the logger. For more

informaon, search for “stac discharge” on onsetcomp.com.

Battery Information

The logger uses one CR2450 non-replaceable lithium baery.

Baery life is not guaranteed past the 1-year logger shelf life.

Baery life for the CX603 and CX703 models is 1 year, typical

with a logging interval of 1 minute. Expected baery life for the

CX603 and CX703 models vary based on the ambient

temperature where the logger is deployed and the frequency of

connecons, downloads, and paging. Deployments in extremely

cold or hot temperatures or a logging interval faster than 1

minute can impact baery life. Esmates are not guaranteed

due to uncertaines in inial baery condions and operang

environment.

All manuals and user guides at all-guides.com

InTemp CX600 Dry Ice/CX700 Cryogenic Logger Manual

www.prosensor.com

WARNING: Do not cut open, incinerate, heat above 85°C

(185°F), or recharge the lithium baery. The baery may

explode if the logger is exposed to extreme heat or condions

that could damage or destroy the baery case. Do not dispose

of the logger or baery in ﬁre. Do not expose the contents of

the baery to water. Dispose of the baery according to local

regulaons for lithium baeries.

All manuals and user guides at all-guides.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Registrador de datos de Intempco

Intempco

Intempco CX600 Series Manual de usuario

Intempco

Intempco CX501 Manual de usuario

Intempco

Intempco CX600 Manual de usuario

Intempco

Intempco CX402-VFC205 Manual de usuario

Intempco

Intempco CX1000 Series Manual de usuario

Intempco

Intempco CX400 Series Manual de usuario

Intempco

Intempco CX450 Manual de usuario

Intempco

Intempco CX500 Series Manual de usuario

Intempco

Intempco CX600 Dry Ice Manual de usuario

Intempco

Intempco CX405 RTD Manual de usuario

Intempco

Intempco CX405 RTD Manual de usuario

Intempco

Intempco CX402-T205 Manual de usuario

Manuales populares de Registrador de datos de otras marcas

TESTO

TESTO 176 Manual de usuario

HT Italia

HT Italia XL421 Manual de usuario

HBM

HBM SOMAT XR CX22B-R Manual de usuario

Agtrix

Agtrix 380i Manual de usuario

Hobo

Hobo H8 Pro Manual de usuario

Beijing ART Tech

Beijing ART Tech PCI2320 Manual de usuario

Athena

Athena GET SL1 Manual de usuario

Motec Systems

Motec Systems C185 Manual de usuario

Beijing ART Tech

Beijing ART Tech USB2832 Manual de usuario

Rotronic

Rotronic HygroLog HL20 Manual de usuario

MRC

MRC DW-6092 Manual de usuario

Racelogic

Racelogic VBOX LapTimer Manual de usuario

Edu-Logger

Edu-Logger 900-240 Manual de usuario

Elma

Elma DT173 Manual de usuario

MadgeTech

MadgeTech PRTemp140 Hoja de especificaciones

Comet

Comet U0121M Manual de usuario

pico Technology

pico Technology PT-104 Manual de usuario

Soil Instruments

Soil Instruments GTecLink Manual de usuario