Intellinet IDC-757IR Manual





IDC-757IR

Outdoor Megapixel Night-Vision

Network Dome Camera

Hardware Installation Guide

Package Contents

Dome Camera IDC-757IR Outdoor Megapixel Night-Vision

Network Dome Camera

Quick Installation Guide

Brief product information and quick

installation

Software CD

IP Surveillance Software

Intelligent IP Installer

User Manuals

Language Packs

Mounting Bracket Three plastic anchors and screws,

Alignment sticker,

4pin I/O connector

Power Adaptor 12V DC, max 9W



Hardware Description





Conduit hole

Dome glass

Cover screw hole

Plug

Cable gland





Power Indicator LED

MicroSD / SDHC

memory card slot

PAL / NTSC video

out mode selector

IR LEDs

Terminal block connector

(digital input / output)

RJ45 Network

Connector

Power connector

(12 V DC)

Analog video

output

Factory reset

Thread-lock sealing nutClawCable gland



LED Indicators



LED Color Indication

Network Green On = Network link

Orange Flashing = Network activity

Power

Red Steady red for booting up process

Blue Turns blue upon completion of start-up

Purple Flashing during firmware upgrading

Unlit Off when press reset button is pressed

SD Card Orange Steady orange means SD card is ready

Flashing when SD card is being accessed



Factory Reset

Reset: With the camera turned on, press the reset button briefly to

reboot the camera, or hold the reset button for 10 seconds to set all

settings back to factory default values.

Digital In-/Ouput & 12 V DC Power Input







Hardware Installation

a. Install the hardware

1. Connect the adaptor to the supplied 2pin I/O terminal block which

shows positive and negative polarity on it. Please make sure the

marked red wire should connect with the positive polarity or device

won’t work. If you are going to use a PoE injector as the power source,

then you won’t need to perform this step.

2. Loosen the tamper-proof screws using supplied special hex wrench and

remove the dome cover from the rugged dome. Be careful do not

scratch the cover glass.

3. Disassemble the cable gland.

4. Thread the network and I/O cable (power/digital input and digital

output) through thread-lock sealing nut, claw (using the claw to round

all cable) and cable gland. To seal all cable in the claw part tightly in

case of water leaking.

5. Attach the cable gland to the conduit hole on the side or bottom of the

rugged dome. Push the claw into the cable gland and tighten thread-

lock sealing nut to secure the cables.

6. Use the supplied blind plug to fill unused conduit hole.

7. Use the cable gland is optional. For vandal-proof requirement of the

cables, use vandal-proof conduits instead.

b. Wall mounting and Ceiling mounting

1. Attach the alignment sticker to the wall/ceiling and drill three pilot

holes through the three circles on the sticker into the wall.

2. Hammer the supplied plastic anchors into the holes.

3. Align the three holes on the base of the camera with the three plastic

anchors on the wall or ceiling, then insert the supplied screws into the

corresponding hole and tighten them.



b. Connect all cables

b1. Power over Ethernet (PoE)

1. Using a standard RJ-45 network cable, connect the dome camera to a

IEEE802.3af compliant PoE switch or PoE injector

b2. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the dome camera

2. Using a standard RJ-45 network cable, connect the camera to a normal

Ethernet Switch or Router

c. Access the camera

Start the IP Installer application to set up the camera. More information

can be found in the user manual on the installation CD.

d. Adjust the viewing angle

Once you have network access to the camera and can see the live image,

you can proceed with adjusting the camera.

d1. Turn the lens module right and left to your desired pan position.

d2. Turn the lens module up and down to your desire tilt position.

d3. Rotate the lens module to adjust the image orientation.



e. Adjust zoom and focus

e1. Loosen the zoom and focus screws anti-clockwise, then adjust the

zoom range and focus by moving the lever left or right. Please note that

the focus adjustment is quite sensitive. Spending some time on getting it

perfect will yield the best possible image quality.

e2. Once you are satisfied with the .result you should tighten the screws

to lock the levers in place.

f. Completion

f1. Clean the dome bubble to remove dust and finger prints.

f2. Fix the tamper-proof screws using supplied special hex. Be careful do

not scratch the cover glass

Otros manuales para IDC-757IR

Tabla de contenidos

Otros manuales de Cámara de seguridad de Intellinet

Intellinet

Intellinet 503792 Manual de usuario

Intellinet

Intellinet IBC-667IR Manual

Intellinet

Intellinet NSC15 Manual de usuario

Intellinet

Intellinet 503181 Manual de usuario

Intellinet

Intellinet 550260 Manual de usuario

Intellinet

Intellinet PRO SERIES Manual de usuario

Intellinet

Intellinet NFC31-WG Manual de usuario

Intellinet

Intellinet NSC11-WN Manual de usuario

Intellinet

Intellinet IDC-757IR Manual

Intellinet

Intellinet IBC-607IR Manual de usuario

Intellinet

Intellinet 524421 Manual de usuario

Intellinet

Intellinet BGC-2010S Series Manual de usuario

Intellinet

Intellinet IBC-637IR Manual del propietario

Intellinet

Intellinet NSC10-WG 550918 Manual de usuario

Intellinet

Intellinet IDC-767IR Manual de usuario

Intellinet

Intellinet NSC15 Manual de usuario

Intellinet

Intellinet NSC15-WG Manual de usuario

Intellinet

Intellinet 550857 Manual de usuario

Intellinet

Intellinet NFD130-IR Manual de usuario

Intellinet

Intellinet NSC15-WG Manual de usuario

Intellinet

Intellinet NSC10-WG 550918 Manual de usuario

Intellinet

Intellinet 550413 Manual de usuario

Intellinet

Intellinet NFC30-IRWG Manual de usuario

Intellinet

Intellinet 550260 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario