Intellinet IBC-667IR Manual

IBC-667IR

Network Bullet Camera

Hardware Installation Guide

Package Contents

Camera Network Bullet Camera

Quick Installation Guide

Brief product information and quick

installation

Software CD

IP Surveillance Software

Intelligent IP Installer

User Manuals

Language Packs

Accessories -Wall mount bracket & U-shape bracket

-Metal plate for wall mount bracket

-Alignment Sticker

-Waterproof Connector

-Screw pack for sun shield &

burglarproof screw

-Screw pack for wall and ceiling

mounting

-Silica gel

-Foam tape

-2 pin terminal blocks for power

-8 pin terminal blocks for DI/DO

Hardware Description

IRLED

Lens

LightSensor

I/O Terminal Block Circuit

I/O Terminal Block Pin Definition

PIN Definition Description Max. V/A

1 Ground -

2 + 12V DC 12V DC

1.2W

3 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

4 AUDIO_Out(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

5 Digital Output 1

Uses an NPN transistor with the emitter connected to the

GND pin. If used with an external relay, a diode must be

connected in parallel with the load for protection against

voltage transients.

100 mA

24V

6 Digital Output 2

Uses an NPN transistor with the emitter connected to the

GND pin. If used with an external relay, a diode must be

connected in parallel with the load for protection against

voltage transients.

100mA

24V

7 Digital Input 1 Connected to GND to activate, or leave floating (or

unconnected) to deactivate. 30V DC

8 Digital Input 2 Connected to GND to activate, or leave floating (or

unconnected) to deactivate. 30V DC

DigitalInput1/2:Max:30VDC

DigitalOutput1/2:Max:24V/100mA

LED Indicators

LED Color Indication

Network Green Active network link

Orange Flashing indicates network activity

Power

Red Steady red during boot-up process

Blue Steady blue when boot sequence has been completed

Unlit When the reset button was pressed for at least 5 sec.

and camera is restarting,

Micro SD / SDHC Orange Steady orange means SD card ready

Flashes orange while accessing SD card

Power Mode

PoE Mode

Power Requirement PoE (IEEE802.3af) with Class 3

Note: While IR on, Heater and Fan will be disabled.

Power Consumption 3.59 W, without IR/Heater/Fan

7.9 W, with max. IR on.

Adaptor Mode

Power Requirement 12V/1.5A Adaptor

Note: While IR on, Heater or Fan would be activated

automatically.

Power Consumption

3.58 W, without IR/Heater/Fan

7.9 W, with max. IR on

9.6 W, with max. IR on / Heater on

8.87 W, with max. IR on / Heater Fan

Note: Heater will be activated while the inner temparature drops under 5C and fan over 50C.

Installing the hardware

1) Assembling sun shield and camera with two supplied screws(M3*6).

2) Fix U-shape bracket to the bottom of camera with supplied screws.

3) Insert all cables (RJ45/power cord/DIDO) into waterproof connector (M25*1.5).

4) Open the front cover and feed all cables through the screw hole of bottom cover from

outside. Connect them to sockets. Then secure the connector tightly.

5) Attach the foam tape and silica gel. (Please change a new silica gel if open the top

cover afterwards.)

6) Lock the front cover. Then secure the burglarproof screw.

7) Feed all cables through the front opening of wall mount bracket.

8) Push the spring mortise of wall mount bracket. Then hook the U-shape bracket onto

the groove of the former.

9) Secure the two screws of wall mount bracket on the other side.

Wall and Ceiling mounting

1) Attached the alignment sticker to the wall. Drill four holes into the wall. Three

holes are for the screws to affix the bracket to the wall, and one larger hole for

the cable. Push the supplied plastic anchors into the screw holes and secure the

plate with the supplied screws (T1/4”*32).

2) Fix the wall mount bracket to the plate with the supplier screws.

3) Position the camera angle by adjusting the pan and tilt.

Lens Focusing

Factory Reset

Reset: With the camera turned on, press the reset button briefly to reboot the camera,

or hold the reset button for 10 seconds to set all settings back to factory default values.

1. Connect the camera via PoE

Using a standard RJ-45 network cable, connect the bullet camera to an

IEEE802.3af/at compliant PoE switch or PoE injector.

2. Connect the camera without PoE

1. Connect the power adaptor to the dome camera

2. Using a standard RJ-45 network cable, connect the camera to a normal

Ethernet Switch or Router

3. Software Installation

Insert the Installation CD into a CD or DVD drive and follow the instructions given

by the Quick Installation Guide.

INTELLINET NETWORK SOLUTIONS™ offers a complete line

of active and passive networking products.

Ask your local computer dealer for more information or visit

www.intellinet-network.com

SOLUTIONS

All products mentioned are trademarks or registered trademarks of their respective

owners.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Intellinet

Intellinet

Intellinet BGC-2010S Series Manual de usuario

Intellinet

Intellinet NSC15 Manual de usuario

Intellinet

Intellinet NSC10 Manual de usuario

Intellinet

Intellinet IDC-757IR Manual

Intellinet

Intellinet 503181 Manual de usuario

Intellinet

Intellinet 550857 Manual de usuario

Intellinet

Intellinet NFC31-WG Manual de usuario

Intellinet

Intellinet NSC15 Manual de usuario

Intellinet

Intellinet 550437 Manual de usuario

Intellinet

Intellinet IBC-607IR Manual de usuario

Intellinet

Intellinet 550857 Manual de usuario

Intellinet

Intellinet NFD130-IR Manual de usuario

Intellinet

Intellinet 524421 Manual de usuario

Intellinet

Intellinet NSC10-WG 550918 Manual de usuario

Intellinet

Intellinet PRO SERIES Manual de usuario

Intellinet

Intellinet 550413 Manual de usuario

Intellinet

Intellinet IDC-767IR Manual de usuario

Intellinet

Intellinet IDC-757IR Manual

Intellinet

Intellinet NSC15-WG Manual de usuario

Intellinet

Intellinet NSC11-WN Manual de usuario

Intellinet

Intellinet NSC10-WG 550918 Manual de usuario

Intellinet

Intellinet 550260 Manual de usuario

Intellinet

Intellinet 503792 Manual de usuario

Intellinet

Intellinet 550260 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario