Intel SRCSAS18E - RAID Controller Manual de usuario

Intel®RAID Controller SRCSAS18E

User’s Guide

Intel Order Number: D26788-003

ii Intel® RAID Controller SRCSAS18E User’s Guidel

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL(R) PROD-

UCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTEL-

LECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN

INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO

LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY,

RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRAN-

TIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR

INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT. Intel products are not intended for use in medical, life saving, life sustaining applications.

Intel may make changes to specifications and product descriptions at any time, without notice.

Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United

States and other countries.

*Other names and brands may be claimed as the property of others.

Intel® RAID Controller SRCSAS18E User’s Guidel iii

Safety Warnings and Instructions

WARNING: English

Important Safety Instructions

Read all caution and safety statements in this document before performing any of the instructions. See also

Intel Server Boards and Server Chassis Safety Information on the Resource CD and/or at

http:\\support.intel.com\support\motherboards\server\sb\cs-010770.htm.

ADVERTENCIAS: Español

Instrucciones de seguridad importantes

Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar cualquiera de las

instrucciones. Vea Intel Server Boards and Server Chassis Safety Information en el CD Resource y/o en

http:\\support.intel.com\support\motherboards\server\sb\cs-010770.htm.I

SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the system,

follow these steps:

1. Turn off all peripheral devices connected to the system.

2. Turn off the system by pressing the power button.

3. Unplug all AC power cords from the system or from wall outlets.

4. Label and disconnect all cables connected to I/O connectors or ports on the back of the system.

5. Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap attached

to chassis ground of the system-any unpainted metal surface-when handling components.

6. Do not operate the system with the chassis covers removed.

A microprocessor and heat sink may be hot if the system has been running. Also, there may be

sharp pins and edges on some board and chassis parts. Contact should be made with care.

Consider wearing protective gloves.

NSTRUCCIONES DE SEGURIDAD: Cuando extraiga la tapa del chasis para acceder al interior del

sistema, siga las siguientes instrucciones:

1. Apague todos los dispositivos periféricos conectados al sistema.

2. Apague el sistema presionando el interruptor encendido/apagado.

3. Desconecte todos los cables de alimentación CA del sistema o de las tomas de corriente alterna.

4. Identifique y desconecte todos los cables enchufados a los conectores E/S o a los puertos

situados en la parte posterior del sistema.

5. Cuando manipule los componentes, es importante protegerse contra la descarga electrostática

(ESD). Puede hacerlo si utiliza una muñequera antiestática sujetada a la toma de tierra del chasis

- o a cualquier tipo de superficie de metal sin pintar.

6. No ponga en marcha el sistema si se han extraído las tapas del chasis.

iv Intel® RAID Controller SRCSAS18E User’s Guidel

WARNUNG: Deutsch

Wichtige Sicherheitshinweise

Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor Sie eine der

Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu Intel-Serverplatinen und -

Servergehäusen auf der Ressourcen-CD oder unter

http:\\support.intel.com\support\motherboards\server\sb\cs-010770.htm.

Si el sistema ha estado en funcionamiento, el microprocesador y el disipador de calor pueden estar

aún calientes. También conviene tener en cuenta que en el chasis o en el tablero puede haber

piezas cortantes o punzantes. Por ello, se recomienda precaución y el uso de guantes protectores.

SICHERHEISMASSNAHMEN: Immer wenn Sie die Gehäuseabdeckung abnehmen um an das

Systeminnere zu gelangen, sollten Sie folgende Schritte beachten:

1. Schalten Sie alle an Ihr System angeschlossenen Peripheriegeräte aus.

2. Schalten Sie das System mit dem Hauptschalter aus.

3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus der Steckdose.

4. Auf der Rückseite des Systems beschriften und ziehen Sie alle Anschlußkabel von den I/O

Anschlüssen oder Ports ab.

5. Tragen Sie ein geerdetes Antistatik Gelenkband, um elektrostatische Ladungen (ESD) über blanke

Metallstellen bei der Handhabung der Komponenten zu vermeiden.

6. Schalten Sie das System niemals ohne ordnungsgemäß montiertes Gehäuse ein.

Der Mikroprozessor und der Kühler sind möglicherweise erhitzt, wenn das System in Betrieb ist.

Außerdem können einige Platinen und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten

an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie sollten Schutzhandschuhe tragen.

Intel® RAID Controller SRCSAS18E User’s Guidel v

AVERTISSEMENT: Français

Consignes de sécurité

Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce document avant de

suivre toute instruction. Consultez Intel Server Boards and Server Chassis Safety Information sur le CD

Resource CD ou bien rendez-vous sur le site http:\\support.intel.com\support\motherboards\server\sb\cs-

010770.htm.

AVVERTENZA: Italiano

CONSIGNES DE SÉCURITÉ: Lorsque vous ouvrez le boîtier pour accéder à l’intérieur du système,

suivez les consignes suivantes:

1. Mettez hors tension tous les périphériques connectés au système.

2. Mettez le système hors tension en mettant l’interrupteur général en position OFF (bouton-

poussoir).

3. Débranchez tous les cordons d’alimentation c.a. du système et des prises murales.

4. Identifiez et débranchez tous les câbles reliés aux connecteurs d’E-S ou aux accès derrière le

système.

5. Pour prévenir les décharges électrostatiques lorsque vous touchez aux composants, portez une

bande antistatique pour poignet et reliez-la à la masse du système (toute surface métallique non

peinte du boîtier).

6. Ne faites pas fonctionner le système tandis que le boîtier est ouvert.

Le microprocesseur et le dissipateur de chaleur peuvent être chauds si le système a été sous tension.

Faites également attention aux broches aiguës des cartes et aux bords tranchants du capot. Nous

vous recommandons l’usage de gants de protection.

PASSI DI SICUREZZA: Qualora si rimuovano le coperture del telaio per accedere all’interno del

sistema, seguire i seguenti passi:

1. Spegnere tutti i dispositivi periferici collegati al sistema.

2. Spegnere il sistema, usando il pulsante spento/acceso dell’interruttore del sistema.

3. Togliere tutte le spine dei cavi del sistema dalle prese elettriche.

4. Identificare e sconnettere tutti i cavi attaccati ai collegamenti I/O od alle prese installate sul retro

del sistema.

5. Qualora si tocchino i componenti, proteggersi dallo scarico elettrostatico (SES), portando un

cinghia anti-statica da polso che è attaccata alla presa a terra del telaio del sistema - qualsiasi

superficie non dipinta.

6. Non far operare il sistema quando il telaio è senza le coperture.

Se il sistema è stato a lungo in funzione, il microprocessore e il dissipatore di calore potrebbero

essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e

sul telaio. È consigliabile l’uso di guanti di protezione.

vi Intel® RAID Controller SRCSAS18E User’s Guidel

When Using Your Computer System

As you use your computer system, observe the following safety guidelines:

Caution: Do not operate your computer system with any cover(s) (such as computer covers, bezels,

filler brackets, and front-panel inserts) removed:

• To help avoid damaging your computer, be sure the voltage selection switch on the

power supply is set to match the alternating current (AC) power available at your

location:

— 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far

Eastern countries such as Japan, South Korea, and Taiwan

— 230 V/50 Hz in most of Europe, the Middle East, and the Far East. Also be sure

your monitor and attached peripherals are electrically rated to operate with the

AC power available in your location.

• To help avoid possible damage to the server board, wait five seconds after turning off

the system before removing a component from the server board or disconnecting a

peripheral device from the computer.

• To help prevent electric shock, plug the computer and peripheral power cables into

properly grounded power sources. These cables are equipped with 3-prong plugs to

ensure proper grounding. Do not use adapter plugs or remove the grounding prong

from a cable. If you must use an extension cable, use a 3-wire cable with properly

grounded plugs.

• To help protect your computer system from sudden, transient increases and decreases

in electrical power, use a surge suppressor, line conditioner, or uninterruptible power

supply.

• Be sure nothing rests on your computer system’s cables and that the cables are not

located where they can be stepped on or tripped over.

• Do not spill food or liquids on your computer. If the computer gets wet, consult the

documentation that came with it.

• Do not push any objects into the openings of your computer. Doing so can cause fire

or electric shock by shorting out interior components.

• Keep your computer away from radiators and heat sources. Also, do not block cooling

vents. Avoid placing loose papers underneath your computer; do not place your

computer in a closed-in wall unit or on a rug.

When Working Inside Your Computer

Note: Do not attempt to service the computer system yourself, except as explained in this guide

and elsewhere in Intel documentation. Always follow installation and service instructions

closely.

1. Turn off your computer and any peripherals.

2. Disconnect your computer and peripherals from their power sources. Also disconnect

any telephone or telecommunications lines from the computer.

Doing so reduces the potential for personal injury or shock.

Intel® RAID Controller SRCSAS18E User’s Guidel vii

Also note these safety guidelines:

• When you disconnect a cable, pull on its connector or on its strain-relief loop, not on

the cable itself. Some cables have a connector with locking tabs; if you are

disconnecting this type of cable, press in on the locking tabs before disconnect the

cable. As you pull connectors apart, keep them evenly aligned to avoid bending any

connector pins. Also, before you connect a cable, make sure both connectors are

correctly oriented and aligned.

• Handle components and cards with care. Don’t touch the components or contacts on a

card. Hold a card by its edges or by its metal mounting bracket. Hold a component

such as a microprocessor chip by its edges, not by its pins.

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside your computer. To prevent static

damage, discharge static electricity from your body before you touch any of your

computer’s electronic components, such as the microprocessor. You can do so by

touching an unpainted metal surface, such as the metal around the card-slot openings at

the back of the computer.

As you continue to work inside the computer, periodically touch an unpainted metal

surface to remove any static charge your body may have accumulated. In addition to the

preceding precautions, you can also take the following steps to prevent damage from

electrostatic discharge (ESD):

• When unpacking a static-sensitive component from its shipping carton, do not remove

the component from the antistatic packing material until you are ready to install the

component in your computer. Just before unwrapping the antistatic packaging, be sure

to discharge static electricity from your body.

• When transporting a sensitive component, first place it in an antistatic container or

packaging.

• Handle all sensitive components in a static-safe area. If possible, use antistatic floor

pads and workbench pads.

viii Intel® RAID Controller SRCSAS18E User’s Guidel

Regulatory and Certification Information

Product Regulatory Compliance

This RAID Controller Card complies with the following safety and electromagnetic

compatibility (EMC) regulations.

Product Safety Compliance

• UL 1950 - CSA 950 (US/Canada)

• EN 60 950 (European Union)

• IEC60 950 (International)

• CE - Low Voltage Directive (73/23/EEC) (European Union)

Product EMC Compliance - Class B

• FCC /ICES-003 (USA/Canada)

• CISPR 22 (International)

• EN55022 (Europe)

• EN55024 (Europe)

• CE - EMC Directive 89/336/EEC (Europe)

• VCCI (Japan)

• AS/NZS 3548 (Australia / New Zealand)

• BSMI CNS13438 (Taiwan)

• RRL, MIC Notice No. 1997-41 (EMC) & 1997-42 (EMI) (Korea)

Product Regulatory Compliance Markings

The RAID controller card is marked with the following compliance markings. Some

marking information may be provided on the packaging and/or in the product

documentation due to limited marking space on the product.

• ETL NRTL Mark (US/Canada)

• FCC Mark (US)

• ICES-003 (Canada)

• CE Mark (Europe)

• VCCI Mark (Japan)

• MIC Mark (Korea)

• BSMI DOC Mark (Taiwan)

• ACS C-Tick Mark (Australia)

Intel® RAID Controller SRCSAS18E User’s Guidel ix

Regulatory Compliance Country Marking

cULus Listing Marks USA/Canada

ETL (NRTL) Mark USA/Canada

CE Mark Europe

FCC Marking (Class A) USA This device complies with Part 15 of the

FCC Rules. Operation of this device is

subject to the following two conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any interference

received, including interference that may

cause undesired operation.

FCC Marking (Class B) USA

EMC Marking (Class A) Canada CANADA ICES-003 CLASS A

CANADA NMB-003 CLASSE A

EMC Marking (Class B) Canada CANADA ICES-003 CLASS B

CANADA NMB-003 CLASSE B

VCCI Marking (Class A) Japan

VCCI Marking (Class B) Japan

xIntel® RAID Controller SRCSAS18E User’s Guidel

BSMI Marking (Class A or

B) and Class A EMC

Warning

Taiwan

RRL MIC Mark Korea

C-Tick Mark Australia

Regulatory Compliance Country Marking

Tabla de contenidos

Otros manuales de Hardware de computadora de Intel

Intel

Intel IB840 Manual de usuario

Intel

Intel Pentium III Processor 512K Guía

Intel

Intel 80C188EC Manual de usuario

Intel

Intel RES2SV240 Manual de instalación

Intel

Intel Pentium 4 mPGA478 Manual de usuario

Intel

Intel SRCU42X Manual de instalación

Intel

Intel BX80571E5300 - Pentium 2.6 GHz Processor Manual de usuario

Intel

Intel BX80623I52500K Manual de usuario

Intel

Intel ECM-APL Manual de usuario

Intel

Intel RS2WC040 Manual de instalación

Intel

Intel SL8K2 - Pentium 4 3.20EGHz 800MHz 1MB Socket 478... Manual de usuario

Intel

Intel RMS3CC080 Manual de usuario

Intel

Intel RMS25PB080 Manual de instalación

Intel

Intel DG45ID - CARACTERISTIQUES TECHNIQUES Manual de usuario

Intel

Intel NUC Kit NUC1ATKPE Manual de usuario

Intel

Intel D5005 Manual de usuario

Intel

Intel CORE 2 DUO MOBILE - THERMAL DESIGN GUIDE... Guía

Intel

Intel WPC2011NA - Pro/wireless 2011 Pccard Wireless... Manual de instalación y operación

Intel

Intel PENTIUM PRO Manual de usuario

Intel

Intel 440GX Guía

Intel

Intel 80C186EA Manual de usuario

Intel

Intel 8XC251SA Guía

Intel

Intel HH80552PG0962M - Pentium 4 3.4 GHz Processor Manual de usuario

Intel

Intel NUC7i5BNH Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario

Jupiter

Jupiter RAM PACK Manual de usuario