Innoband AV 200P-I1 Manual de usuario

HomePlug AV 200P-I1

User Manual

Issue 2.0

15th, March, 2010

- 2 -

User Manual

INNOBAND HOMEPLUG AV 200P-I1

Information in this document is subject to change without notice and does not represent a

commitment on the part of Innoband Technologies, Inc. The software described in this document is

furnished under a license agreement and may be used or copied only in accordance with the terms

of the license agreement. It is against the law to copy the software on any other medium except as

specifically allowed in the license agreement. The licensee may make one copy of the software for

backup purposes. No part of this manual may be reproduced or transmitted in any form or by any

means, electronic or mechanical, including photocopying and recording, for any purpose without the

written permission of Innoband Technologies, Inc.

Manual Version 1.0

July 2010

Innoband™ is a trademark of Innoband Technologies, Inc. The trademarks, logos and service marks

(“Marks”) displayed on this manual are the property of Innoband or other third parties. Users are not

permitted to use these Marks without the prior written consent of Innoband or such third party that

may own the Marks. IBM is a registered trademark of International Business Machines Corporation.

Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and

the Windows logo are registered trademarks of Microsoft Corporation. All other products are

trademarks or registered trademarks of their respective owners.

- 3 -

Table of Contents

USER MANUAL .........................................................................................................................................................2

PRODUCT INTRODUCTION...................................................................................................................................4

FEATURES & SPECIFICATIONS...........................................................................................................................5

GETTING STARTED.................................................................................................................................................6

FEATURES -HOMEPLUG AV 200P-I1 ETHERNET BRIDGE.............................................................................................6

HARDWARE OVERVIEW ................................................................................................................................................7

HomePlug AV 200P-I1..........................................................................................................................................7

Sync Button Function: ...........................................................................................................................................8

HomePlug AV 200P-I1 Application Scenarios:.....................................................................................................8

Application Illustration........................................................................................................................................10

INSTALLATION PROCEDURES..........................................................................................................................11

HOMEPLUG AV 200P-I1 UTILITY INSTALLATION........................................................................................................13

STARTING HOMEPLUG AV 200P-I1 UTILITY.................................................................................................19

UNDERSTANDING 200P-I1 UTILITY............................................................................................................................20

Main Tab .............................................................................................................................................................20

Password Setup Procedure:.......................................................................................................................................... 22

To add a new device to a network:............................................................................................................................... 23

Privacy Tab..........................................................................................................................................................24

Diagnostics Tab...................................................................................................................................................25

About Tab ............................................................................................................................................................27

TROUBLESHOOTING............................................................................................................................................28

APPENDIX A - WARRANTIES..............................................................................................................................29

APPENDIX B - REGULATION ..............................................................................................................................31

APPENDIX C – CONTACT INFORMATION......................................................................................................32

- 4 -

Product Introduction

Innoband HomePlug AV 200P-I1 is a networking device that utilizes the existing wiring system

as a path to transmit data signal through the inter-conversion between digital and analog signal.

With this functionality, 200P-I1 can be plugged into an electrical socket to draw power and at the

same time establishing a network connection between two or more Ethernet devices.

The Innoband HomePlug AV 200P-I1 can be used to bridge any Ethernet device to your

Powerline network in your home or office. With this technology, Ethernet devices in your home or

office can equally share high speed data transmission rate without the need to spend excessive

time and money installing expensive Ethernet cable. It can be plugged into an Ethernet port on a

router to equip a network with Powerline capabilities and take advantage of the router features.

The 200P-I1 can also be plugged directly into a cable or DSL modem that allows instant internet

access over home Powerline to each computer equipped with a HomePlug AV certified Powerline

network adapter. Innoband HomePlug AV 200P-I1 makes high-speed modem sharing as fast and

simple as plugging the devices in the wall.

- 5 -

Features & Specifications

Protocol TDMA, CSMA/CA

Standard Ethernet specification: IEEE 802.3, IEEE 802.3x,

IEEE 802.3u, Auto MDI/MDIX

Transmission speed 200Mbps

Optimal Coverage Range 200M

Modulation Supports OFDM - 1155 carriers,1024 / 256/64

QAM, QPSK, BPSK and ROBO

Frequency Band 2MHz ~ 30MHz

Security 128-bit AES encryption over household power supplier

grid

Device port Ethernet RJ-45

Operation System Windows 98_SE / Me / 2000 /XP(32 and 64 bit)/ Vista (32

and 64 bit)

RAM 128Mb

Power Supplier Specification Input: 100~240V AC, 50~60Hz

Physical Interface • Interface: Ethernet 10/100M (MDI/MDIX) switch

• Sync button

• Reset button

• Power AC Plug

• LED display:

- 1.0 DET LED

- POWER LED

- PLC (Powerline Link/Act) LED

- ETH (Ethernet Link/Act) LED

Dimension 112.35 X 77.70 X44.50 mm

Power Saving Reduce power consumption by at least 60% during power

saving mode.

Operating Temperature /

Humidity

• Operating temperature: 0 ~ 400C

•Storage temperature: -20 ~ 700C

• Humidity: 5~95% non-condensing

- 6 -

Getting Started

Safety Warnings

1. Do not use the adapter in high humidity or high temperature environment.

2. Do not open or repair the case yourself.

3. Avoid using this product and all its accesories outdoor.

4. Place the adapter on a stable surface.

5. Only “HomePlug AV” compliant Powerline Communication (PLC) adapter for remote

access is necessary.

Features - HomePlug AV 200P-I1 Ethernet Bridge

1. Physical layer data rate up to 200Mbps over existing Powerline.

2. Uses powerline technology that takes advantage of the unused bandwidth of the

electrical wiring in the home.

3. Ideal for Triple Play applications such as IPTV, VoIP telephony and high-speed

Internet access.

4. Support 10/100 (MDI/MDIX) Ethernet switching.

5. Compliant with the HomePlug Powerline Alliance Industry specification HomePlug

AV.

6. Power supplier design inside.

7. Ideal for Residential Users.

8. Power Saving mode: When PC or other Ethenet devices are completely power off,

Innoband HomePlug device will automatically enter power saving mode which will

help to reduce approximately 60% of power consumption.

- 7 -

Hardware Overview

HomePlug AV 200P-I1

The Description of each labeled part is described in the table below.

1.0 DET LED Blink when detect the presence of other HomePlug 1.0

devices that have the transmission rate of 14 or 85 Mbps.

Note: Due to the incompatibility of HomePlug AV 200 with

HomePlug 1.0 devices, the presence of the HomePlug 1.0

devices within the powerline network will thus reduce the

performance of your powerline network.

Power LED Lit when the power is on.

PLC (Powerline Link/Act) LED Lit when a network has been established. Blink when

powerline data is transmitted or received.

ETH (Ethernet Link/Act) LED Lit when an Ethernet data signal is transmitted or received.

Sync Button Used to establish a LAN network with other Ethernet devices.

Reset Button Press this button to restore the device configuration to factory

default.

Ethernet Port Connect the HomePlug AV device with an Ethernet device

(eg. PC or modem router) with the Ethernet cable included.

Power Plug / AC Power Cord Plug into an electric socket to draw power and to form a

powerline network with other HomePlug AV devices.

PLC LED

Power LED

1.0 DET LED

ETH LED

Sync Button

Reset Button

Power Plug

Ethernet Port

- 8 -

Sync Button Function:

There are 3 types of Sync Button trigger states:

1. Broadcast State: A 200P-I1 device can provide information for another 200P-I1

device to join its powerline network group (works even if it is currently the only

device existing within the network group).

2. Join State: For an ungrouped 200P-I1 device to join an existing powerline network

group.

3. Press the Sync Button on the first 200P-I1 device to turn it to Broadcast State. Then

press the Sync Button of an ungrouped 200P-I1 device to turn it to a Join State.

4. Ungroup State: Press the Sync Button for more than 10 seconds to separate the

device from its current attached network group.

HomePlug AV 200P-I1 Application Scenarios:

Scenario 1: A 200P-I1 device A wants to form a network group with another 200P-I1 device

You can allocate whichever device (A or B) to be the Broadcast State and the Join State.

Example:

1. Hold down the Sync Button of device A for 1~3 seconds to turn it into Broadcast

State.

2. Hold down the Sync Button of device B for 1~3 seconds to turn it into Join State.

3. Wait for the Sync LED of both devices to light up then you will now have both

devices being in the same network group.

Note: Once the device is plugged into the electric socket, connect it with an Ethernet cable

within 60 seconds to prevent the device from Auto Power Off.

Scenario 2: A 200P-I1 device wants to join an existing network group BC

Device A wants to join a network group “BC” currently consisting of device B and device C. Any

devices within the “BC” group can become the “Broadcast State” and device A will be the “Join

State”.

Example:

1. Hold down the Sync Button of device B or C from the BC network group for 1~3

seconds to turn it into Broadcast State.

2. Hold down the Sync Button of device A for 1~3 seconds to turn it into Join State.

3. Wait for the Sync LED of both devices A and (B or C) to light up then you will now

have device A join the BC network group.

Note: Once the device is plugged into the electric socket, connect it with an Ethernet cable

within 60 seconds to prevent the device from Auto Power Off.

- 9 -

Scenario 3: A 200P-I1 device A of network group AD wants to join an existing network

group BC.

For a device which already belongs to a network group is to join with a different network group,

that device has to be ungrouped from its current attached group first.

Example:

1. Hold down the Sync Button of device A for more than 10 seconds to ungroup it from

network group AD.

2. Then hold down the Sync Button of device (B or C) of network group BC for 1~3

seconds to turn it to Broadcast State.

3. Hold down the Sync Button of device A again for 1~3 seconds to turn it to Join State.

4. Wait for the Sync LED of both devices A and (B or C) to light up. Now you will have

device A join the network group BC.

Note: Once the device is plugged into the electric socket, connect it with an Ethernet cable

within 60 seconds to prevent the device from Auto Power Off.

- 10 -

Application Illustration

Tabla de contenidos

Otros manuales de Enrutador de red de Innoband

Innoband

Innoband 8012-B1 Manual de usuario

Innoband

Innoband 8012-R2 Manual de usuario

Innoband

Innoband 8520-B1 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad