Ingics iGS03W Manual de usuario
INGICS TECHNOLOGY
Guide
Ver.01a
Beacon Gateway
iGS03W/E/M User
Manual
iGS03W/E/M is a gateway to bridge the local BLE( Bluetooth® Low Energy) tags,
sensors, or beacons to remote server/cloud by WiFi, Ethernet or LTE-M. Through an
easy web UI interface, user can configure the Internet access to upload reports to
cloud server by TCP, HTTP(S), or MQTT(S). This guide is to help the user to figure out
how to operate and configure the iGS03.
Contents:
Overview
Block Diagram
SIM
WiFi
Ethernet
BLE
GNSS
Example case 1: The device is in fixed position:
Example case 2: The device is moving:
Payload Format
BLE
GPS
Button
Reset to Default
WPS
LEDs
Configuration
Web User Interface
System
Wi-Fi
AP Mode
Station Mode
Network
WiFi Address
DHCP Server (WiFi AP)
Applications
TCP Server
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
1
INGICS TECHNOLOGY
TCP Client
HTTP Client
HTTPS
MQTT Client
MQTTS
Common Settings
Content Type
Keep Alive
Append Timestamp
Request Interval
Cache full handling
Throttle Control
Cloud IoT Helper
Advanced
BLE Configuration
BLE-5 PHY Mode
Active Scan Mode
BLE Filter
RSSI Threshold
Payload Whitelist
BLE MAC Whitelist
Security
Device Key/Certification/Server CA Upload
LTE
LET Settings
APN
Auth
Username/Password
GNSS Settings
NTP Setting
Certification
Bluetooth SIG Qualification
Japan MIC Reaulatory
FCC Regulatory
FCC Statements
CE Regulatory
Revision History
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
2
INGICS TECHNOLOGY
Overview
The iGS03 BLE gateway scans beacons(like iBeacon or Eddystone), proprietary tags, or BLE
sensors then sends the payload to TCP, HTTP or MQTT server. Users can configure the transmit period
and server endpoint through a simple web UI. There are three models, iGS03W, iGS03E and iGS03M,
representing different uploading interfaces, WiFi, Ethernet and LTE-M.
Block Diagram
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
3
INGICS TECHNOLOGY
SIM
To use iGS03M (LTE-M Model), you have to put a Cat-M1 micro SIM card into the socket of
iGS03M. Please open the bottom cover to insert the SIM card. The steps to open the bottom cover are
as below,
Step 1. Remove external BLE antenna
Step 2. Remove the screw from bottom cover
Step 3. Use finger to press and hold the arrow
part
Step 4. Pull out the bottom cover
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
4
INGICS TECHNOLOGY
WiFi (iGS03W/iGS03M)
The 2.4G WiFi AP connection is used to configure the unit through web UI. iGS03 works as an
WiFi Access Point(AP) supporting DHCP. Users must connect to this AP to configure the unit.
Ethernet (iGS03E)
It supports 10BASE-T and 100BASE-TX with HP Auto-MDIX. Through the Ethernet, the gateway
can bridge your BLE devices to the local TCP server or cloud server for management.
BLE
The BLE subsystem operates in listening mode. It collects the messages advertised by BLE
devices. These messages are then sent to the cloud server configured by the user.
iGS03 supports two BLE modes
1. LE 1M PHY: including BLE4.2(Legacy)/BLE5, 1M in 100% duty cycle
2. LE Coded PHY: BLE5, 125K(Long Range) in 100% duty cycle
The default PHYMODE is 1, LE 1M PHY mode.
Users can use webUI or telnet command to configure the mode.
GNSS (iGS03M)
The GNSS function is turned “off” by default. Users can use webUI to enable or disable GNSS.
For detail settings, use below telnet commands to manage the GNSS behavior:
GNSS ENABLE Enable/Disable GNSS, default off
GNSS FIXCOUNT Number of attempts for positioning, 0 indicates continuous positioning.
default 0
GNSS FIXRATE The interval time between the first and second time positioning, default 1 (1
second)
GNSS RPTRATE The interval time for sending GPSR report, default 600 (10 minutes)
GNSS INFO To get latest GPS status
Example case 1: The device is in fixed position:
e.g.
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
5
INGICS TECHNOLOGY
GNSS ENABLE 1
GNSS FIXCOUNT 5
GNSS FIXRATE 60
GNSS RPTRATE 60
Then GNSS will be enabled and get positioned for 5 times with a 60 seconds interval.
GNSS will be off automatically after getting position for 5 times.
Example case 2: The device is moving:
e.g.
GNSS ENABLE 1
GNSS FIXCOUNT 0
GNSS FIXRATE 1
GNSS RPTRATE 60
Then GNSS will be enabled and continuously get position with 1 second interval, and it will send
a GPSR report every 60 sec.
You can also use the "GNSS INFO" command to get the latest coordinates.
Payload Format
There are several kinds of payload format that iGS03 will send to the server.
BLE
General format:
$<report type>,<tag id>,<gateway id>,<rssi>,<raw packet content>,*<unix epoch timestamp>\r\n
<report type>
Different report type to distinguish the source of the report.
<tag id>
MAC address or ID of tag/beacon
<gateway id>
MAC address of gateway
<rssi>
RSSI of tag/beacon
<raw packet content>
Raw packet received by the gateway
<unix epoch timestamp>
Optional timestamp configured in applications page
Report Type:
$GPRP BLE4.2 General Purpose Report
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
6
INGICS TECHNOLOGY
$RSPR BLE4.2 Scan Response Report
$LRAD BLE5 Long Range ADV
$LRSR BLE5 Long Range Scan Response
$1MAD BLE5 1M ADV
$1MSR BLE5 1M Scan Response
Examples:
$GPRP,CCB97E7361A4,CB412F0C8EDC,-49,1309696773206D65736820233220285445535429020106,1574921085
$GPRP,E5A706E3923A,CB412F0C8EDC,-87,0201041AFF590002150112233445566778899AABBCCDDEEFF0000100C3BB,157
4921085
$LRAD,51A88AD374B7,CC4B73906F96,-87,02010212FF0D0083BC280100AAAAFFFF000010030000,1574921085
$GPRP,0C61CFC1452E,E7DAE08E6FC3,-44,0201061AFF4C000215B9A5D27D56CC4E3AAB511F2153BCB9670001452ED6
(iBeacon, UUID: B9A5D27D56CC4E3AAB511F2153BCB967, Major: 0001, Minor: 452E)
GNSS (iGS03M)
General format:
$GPSR,<tag_mac>,<reader_mac>,<rssi>,yymmdd,hhmmss.ss,latitude,longitude,speed,hdop(,timestamp)
●"$GPSR,<tag_mac>,<reader_mac>,<rssi>" fields are for compatibility with other reports. The
tag_mac is always the same as reader_mac and the rssi is always -127.
●yymmdd,hhmmss.ss is the UTC time when the position is acquired.
●speed: The unit is knots.
●hdop: Horizontal dilution of position
Example:
$GPSR,CC4B73906F96,CC4B73906F96,-127,191127,233821.00,24.993631,121.423264,0.0,2.4,1574897900
Button
One button is located on the back panel. It is used for WPS function or Reset to default settings.
Function
Trigger Condition
WPS (iGS03W/M)
short press for over 1sec and release
Reset to default settings
long press for over 3 sec
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
7
INGICS TECHNOLOGY
Reset to Default
Pressing the reset button on your device for over 3 secs to retrieve the default setting. While the
network status LED turns into red light, release the button, and the iGS03M will reboot with its default
settings.
WPS
Users can use the WPS button to join iGS03W/M to the WiFi Access Point. First press the WPS
button on your Access Point, when it is ready, then press the WPS button for over 1 sec on the iGS03M
device to join the Access Point.
LEDs
There are two LEDs indicating the current status. The left one is BLE status LED and the right one
is Network status. Below are their behaviors.
On
Flash
BLE
Status
LED
find tag/beacon in range
BLE transmission
happening
Network
Status
LED
WiFi/LTE-M connection
success
(This only implies the network
is connected. It doesn’t mean
the server is connected)
Green: WiFi/LTE-M
network transmission
happening
Orange:
If IGS03M does not insert
SIM card and being used
as WiFi device
Network Status LED behavior
Description
Status
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
8
INGICS TECHNOLOGY
ORANGE LED on (500ms)
Boot start
Booting
RED LED blink (100ms on/off)
Joining AP (If WiFi in STA mode)
Booting
RED LED blink (500ms on/off)
LTE connecting carrier
Booting
GREEN/ORANGE LEDs blink interleaved
(100ms)
WPS enrollee
WPS
GREEN LED on
Network ready
Ready/Idle
ORANGE LED on
Network ready (If SIM card is not inserted)
Ready/Idle
GREEN LED blink (200ms on/off)
Network is transfering data
(If SIM card is not used on iGS03M, shows
ORANGE LED blink instead)
Busy
RED LED ON (1sec)
Connect failure
Error
RED LED blink (5sec on/off)
Misconfiguration
Error
RED LED ON (5sec)
LTE init failure
Error
Configuration
iGS03W & iGS03M
To configure the unit, you have to connect it through the WiFi interface. When it is powered on,
you could scan its native AP and connect it with the WiFi of your NB/PC/Mac/Tablet/Smartphone. It’s
SSID is just like the below figure with part of the mac address. The default key to connect with it is
“12345678”. You can change it later when you get into the web UI.
After connection, enter IP address 192.168.10.1 in your browser. The default account/password
are both “admin”. The following sections describe details of the web UI.
iGS03E
iGS03E is a DHCP client by default. To configure it, you have to connect it to a router with DHCP
enabled. The first thing is to find iGS03E’s IP address in this network so that you can get into it’s webUI
for configuration. If you don’t know the IP address, you may need to use some tool to find it.(For
example, “Fing” APP in Android & iOS. Join your smartphone or tablet with “Fing” in the same network.
And use it to scan all the devices in this network)
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
9
INGICS TECHNOLOGY
Web User Interface
You can review current configuration or modify it on the web UI. There are various function
groups listed on the top of UI.
Any change in the page needs to be saved first before switching to another page, otherwise the
modification will be lost. And after all changes made, click reboot to make the changes effective.
System
Display firmware and device information, including MAC address and IP address in station mode
are shown here.
Wi-Fi
Users can configure iGS03M’s WiFi device as an WiFi AP or join to the other AP. The related
settings can be managed on this page.
AP Mode
SSID: The default name is IGS03 plus
the last digits of the mac address.
Security: Open, WPA-PSK, WPA2-PSK
and WPA-PSK/WPA2-PSK are
supported. WPA2-PSK is
recommended.
Password: 8-63 characters can be
input
Channel: 1~11(ch12 and ch13 could be supported by request)
Station Mode
This mode is used for transferring
data by *WiFi.
Scan: Click it to scan available APs.
INGICS TECHNOLOGY CO., LTD. • [email protected] • WWW.INGICS.COM
10
Otros manuales para iGS03W
3
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Puerta de Ingics
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
