Ingenico ICMP Manual de usuario

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2

Service Manual

ingenico iCMP

Wireless EMV Reader

to Voyager Connection Reset

Tech Guide

18805 Adams Ct., #110 ~ Morgan Hill, CA 95037, USA ~ +1-408.924.0808 ~ www.washlinksystems.com ~ support@washlinksystems.com

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2 of

1 7

This tech guide should be followed in the event your Ingenico iCMP Wireless EMV

reader fails to connect to the Washlink Systems Voyager Saleslink terminal.

Follow this guide’s steps in order. If the current step fails, proceed to the next step. If

itsucceeds, you may stop reading and carry on with processing transactions as

normal.

If you reach the end of this guide and still the iCMP will not connect, contact Washlink

Systems support; +1-408-924-0808, support@washlinksystems.com

This tech guide should be followed in the event your Ingenico iCMP Wireless EMV

reader fails to connect to the Washlink Systems Voyager Saleslink terminal.

Follow this guide’s steps in order. If the current step fails, proceed to the next step. If

itsucceeds, you may stop reading and carry on with processing transactions as

normal.

If you reach the end of this guide and still the iCMP will not connect, contact Washlink

Systems support; +1-408-924-0808, support@washlinksystems.com

• The image above is what the iCMP will show when connected and in standby

mode. Note: this message may vary depending on your configuration.

• The iCMP connects to the Voyager terminal using Bluetooth

• Out of the box and after fully booted, the iCMP’s default message shows

“LISTENING FOR INPUT”. This text can be changed via the RCM software.

• The image above is what the iCMP will show when connected and in standby

mode. Note: this message may vary depending on your configuration.

• The iCMP connects to the Voyager terminal using Bluetooth

• Out of the box and after fully booted, the iCMP’s default message shows

“LISTENING FOR INPUT”. This text can be changed via the RCM software.

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2 of

2 7

If your iCMP has the message shown in either of the above images, the iCMP has

timed out and has lost it’s connection to the Voyager terminal. Follow the steps within

this guide until the iCMP is reconnected.

If your iCMP has the message shown in either of the above images, the iCMP has

timed out and has lost it’s connection to the Voyager terminal. Follow the steps within

this guide until the iCMP is reconnected.

If you see no text, the iCMP may be powered off. Press the power button for

approximately one second. The iCMP will reboot. This may take several minutes.

If the device does not power on, jump to the Troubleshooting section of this document

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2 of

3 7

If the screen indicates the iCMP has timed out, the first and easiest thing to try is to

briefly press the power button on the right side ofthe reader. Typically this will wake

up the reader and force it to attempt a reconnect to the Voyager terminal. When you

see your usual home screen (Welcome or your own custom message) the iCMP is

connected. You may now continue processing credit card transactions as normal.

If pressing the power button doesn’t wake up the iCMP or it’s awake and credit card

transactions time out, it’s possible the iCMP is still not connected to Voyager. Continue

following along with this document.

If the screen indicates the iCMP has timed out, the first and easiest thing to try is to

briefly press the power button on the right side ofthe reader. Typically this will wake

up the reader and force it to attempt a reconnect to the Voyager terminal. When you

see your usual home screen (Welcome or your own custom message) the iCMP is

connected. You may now continue processing credit card transactions as normal.

If pressing the power button doesn’t wake up the iCMP or it’s awake and credit card

transactions time out, it’s possible the iCMP is still not connected to Voyager. Continue

following along with this document.

Step 1:

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2 of

4 7

Step 2:

• Fully reboot the iCMP.

• To turn off the reader, press the Yellow button and the # button at the same time.

This will turn the iCMP completely off.

• Now turn the iCMP on by pressing the power button for approximately one second.

The reader will reboot. This may take several minutes.

• Upon reboot, the Bluetooth connection icon on the iCMP will be visible indicating

ithas reconnected to the terminal .

Powering cycling the iCMP in this manner should result in a reconnection. If it doesn’t

or you’re still unable to process credit card transactions, continuing reading this

document.

• Fully reboot the iCMP.

• To turn off the reader, press the Yellow button and the # button at the same time.

This will turn the iCMP completely off.

• Now turn the iCMP on by pressing the power button for approximately one second.

The reader will reboot. This may take several minutes.

• Upon reboot, the Bluetooth connection icon on the iCMP will be visible indicating

ithas reconnected to the terminal .

Powering cycling the iCMP in this manner should result in a reconnection. If it doesn’t

or you’re still unable to process credit card transactions, continuing reading this

document.

• Fully reboot the iCMP.

• To turn off the reader, press the Yellow button and the # button at the same time.

This will turn the iCMP completely off.

• Now turn the iCMP on by pressing the power button for approximately one second.

The reader will reboot. This may take several minutes.

• Upon reboot, the Bluetooth connection icon on the iCMP will be visible indicating

ithas reconnected to the terminal .

Powering cycling the iCMP in this manner should result in a reconnection. If it doesn’t

or you’re still unable to process credit card transactions, continuing reading this

document.

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2 of

5 7

Step 3:

• On Voyager, right click on the RCM icon in the system tray in the lower right

hand side of the terminal (by the clock).

• Click on “Device Configure”.

• Press “Test” or “Load Forms to Device”.

• Follow the steps on both the RCM and iCMP. If the test is successful, you should

now see the Welcome message or your custom text on the iCMP. You may now

process transactions as usual.

If the test fails, continuing reading this document.

• On Voyager, right click on the RCM icon in the system tray in the lower right

hand side of the terminal (by the clock).

• Click on “Device Configure”.

• Press “Test” or “Load Forms to Device”.

• Follow the steps on both the RCM and iCMP. If the test is successful, you should

now see the Welcome message or your custom text on the iCMP. You may now

process transactions as usual.

If the test fails, continuing reading this document.

RCMRCM

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2 of

6 7

Step 4:

• Reboot Voyager. This combined with the previous steps you’ve already taken

should reestablish the connection between Voyager and the iCMP.

• First close Saleslink and any other programs running on Voyager.

• Now go to the lower left side of the windows menu screen and select “Shut down”.

You may also choose “Reboot”.

• If you chose to Shut Down, go to the upper left side of the Voyager terminal and

press the power button. Wait for the terminal to reboot.

• If the iCMP still fails to connect, repeat the steps of this document in order.

If after rebooting and rerunning the steps in this document you’re still unable to

process transactions as normal, continue reading this document.

• Reboot Voyager. This combined with the previous steps you’ve already taken

should reestablish the connection between Voyager and the iCMP.

• First close Saleslink and any other programs running on Voyager.

• Now go to the lower left side of the windows menu screen and select “Shut down”.

You may also choose “Reboot”.

• If you chose to Shut Down, go to the upper left side of the Voyager terminal and

press the power button. Wait for the terminal to reboot.

• If the iCMP still fails to connect, repeat the steps of this document in order.

If after rebooting and rerunning the steps in this document you’re still unable to

process transactions as normal, continue reading this document.

Shut Down Windows

(same as any typical Windows computer)

Power button

Ingenico iCMP wireless EMV Reader: TechGuide

Document Revision: v1.1.2 of

7 7

Troubleshooting:

• If the screen looks like the image above (blank/no text) it’s possible that the EMV

reader needs charging. Attach a micro USB cable into a charging device and the

screen should light up. Let it charge until the screen indicates full charge (typically

3 hours from empty to full charge). Then repeat this document if necessary.

• If after a few minutes having plugged in to a charging source you get the same

blank screen try a different cable/charging source and try again.

• At that point if the screen is still blank contact Washlink Support.

• If you get this far and still cannot process transactions as usual, contact Washlink

support and our team will help from here.