Infineon PSoC 62S4 Manual de usuario

1 KitProg3 status LED (D10)

2 KitProg3 USB connector (J10)

3 PSoC 5LP programming header (J7)*

4 2.5 V selection jumper (J14)

5 PSoC 6 MCU power selection jumper (J12)

6 PSoC 5LP based KitProg3 programmer

and debugger (CY8C5868LTI-LP039, U7)

7 PSoC 6 MCU current measurement jumper (J13)

8 KitProg3 programming mode selection button (SW3)

9 Power LED (D14)

10 PSoC 6 MCU reset button (SW1)

11 Arduino™ UNO R3 compatible power header (J1)

12 PSoC 6 MCU 10-pin SWD/JTAG program and debug header (J8)

13 User LEDs (D12 and D13)

14 Arduino UNO R3 compatible I/O headers (J2, J3 and J4)

15 PSoC 6 MCU user button/hibernate wakeup (SW2)

16 PSoC 6 MCU (CY8C6244LQI-S4D92, U8)

17 CapSense™ buttons and slider (CSB1, CSB2 and CSS1)

18 Thermistor (TH1)

19 Ambient light sensor (Q8)

20 QSPI NOR flash (S25FL512SAGMFIR10, U9)

21 PSoC 6 MCU USB connector (J5)

22 PSoC 6 MCU extended I/O header (J11)*

23 External power supply connector (J9)*

* Footprint only, not populated on the board

PSoC 62S4 pioneer board details

PSoC 62S4 pioneer board pinout details

www.cypress.com/CY8CKIT-062S4

Quick start guide

PSoC™ 62S4 pioneer kit

CY8CKIT-062S4

The PSoCTM 62S4 pioneer kit (CY8CKIT-062S4) is a low-cost hardware

platform that enables you to design and debug applications using

the PSoC 62 MCU.

Kit contents

PSoC 62S4 pioneer board

USB type-A to micro-B cable

Six jumper wires (five inches each)

Quick start guide (this document)

›

10 11 12 14

13 15 16

1921 20142223

P6_4/SCL

P6_5/SDA

VREF/AREF

GND/GND

P2_2/D13

P2_1/D12

P2_0/D11

P2_3/D10

P2_6/D9

P2_4/D8

P6_3/D7

P6_2/D6

P5_7/D5

P5_6/D4

P5_1/D3

P5_0/D2

P0_3/D1

P0_2/D0

P8_1

P8_0

P7_3

P7_2

P7_1

P7_0

P2_7

P2_5

P0_4

P0_5

Arduino Uno R3 I/Os

LEGEND

PSoC 6 MCU I/Os

VTARG/IOREF

XRES/RESET

V 3.3/3.3 V

V 5.0/5 V

GND/GND

VIN/Vin

P10_0/A0

P10_1/A1

P10_2/A2

P10_3/A3

P10_4/A4

P10_5/A5

P10_6

P10_7

P9_0

P9_1

P9_2

P9_3

P3_0

P3_1

Before you start

› Ensure that you have the following:

• PC with USB port

• UART terminal soware such as Tera Term

or Minicom

›

Visit the kit website to download and install the

required soware.

› Ensure the jumper J12 is at position 2-3 to select 3.3 V.

› Connect the KitProg3 USB connector (J10) to your PC.

› Wait for the driver installation to complete.

Step 1: Connect the kit with UART terminal soware

› Open the UART terminal soware and connect to

the kit’s USB-UART COM port with the following settings:

• Baud rate: 115200 bps

• Data: 8 bit

• Parity: None

• Stop bit: 1 bit

• Flow control: None

› Press the XRES switch (SW1) to reset the device.

Step 2: Run the pre-programmed code example

› Follow the instructions displayed on the UART

terminal to use the pre-programmed

code example.

Step 3: Observe the user LED (D13) brightness variation

› Observe the state of the user LED (D13) with the variation

of ambient light intensity. The LED turns ON when the

ambient light intensity is lower than 45% and turns OFF

when higher than 55%.

Quick start guide

PSoC 62S4 pioneer board

USB-UART COM port setup

Instructions displayed on the UART terminal

Observe the brightness in LED (D13)

Document Number: 002-30749 Rev. *C

Este manual sirve para los siguientes modelos

Otros manuales de Hardware de computadora de Infineon

Infineon

Infineon XMC7200 Manual de usuario

Infineon

Infineon EZ-PD PMG1 Manual de usuario

Infineon

Infineon CYSBSYSKIT-DEV-01 Manual de usuario

Infineon

Infineon CDM10V Manual de usuario

Infineon

Infineon TRAVEO T2G Manual de usuario

Infineon

Infineon SPI F-RAM FM33256B Manual de usuario

Infineon

Infineon TRAVEO II Manual de usuario

Infineon

Infineon AIROC CYBLE-343072-EVAL-M2B Manual de usuario

Infineon

Infineon TLE493D-P2B6 MS2GO Manual de usuario

Infineon

Infineon EVAL-XMC4800PSOC6M5 Manual de usuario

Infineon

Infineon AIROC CYW20829 Manual de usuario

Infineon

Infineon ICL8001G Manual de instrucciones

Infineon

Infineon FingerTIP FTF 1100 MF1 Manual de usuario

Infineon

Infineon TLE4972 Manual de usuario

Infineon

Infineon REF-Vacuum-C101-2ED Manual de usuario

Infineon

Infineon Cypress S6SATU01A Series Manual de usuario

Infineon

Infineon Traveo II CPU board Manual de usuario

Infineon

Infineon BTN9970 Manual de usuario

Infineon

Infineon EZ-PD PAG2S-2P Manual de usuario

Infineon

Infineon XMC1400 Manual de usuario

Infineon

Infineon AURIX TC 4 Series Manual de usuario

Infineon

Infineon BGT60LTR11AIP EBG Manual de usuario

Infineon

Infineon AN230264 Manual de usuario

Infineon

Infineon AIROC CYW9 907 Series Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario