Impex MARCY MWB CR 4 Manual de usuario

MARCY CORNER GYM

CR 4

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

info@impex-fitness.com

NOTE:

Please read all instructions

carefully before using this

product

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

How to Use

Warranty

Ordering Parts

Model

MWB CR 4

Retain This

Manual for

Reference

6-18-01

OWNER'S

MANUAL

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE IDENTIFIER.....…....................................................................... 3

ASSEMBLY INSTRUCTIONS........................................................................... 4

PARTS LIST…………………………………………………………….…………….21

RESISTANT CHART…………………………………………………………………22

HOW TO USE…………………………………………………………………………23

WARRANTY.................................................................................................… 24

ORDERING PARTS......................................................................................... 24

BEFORE YOU BEGIN

Thank you for selecting the MARCY CR4 PERSONAL TRAINER by IMPEX

FITNESS PRODUCTS. For your safety and benefit, read this manual carefully

before using the machine. As a manufacturer, we are committed to provide you

complete customer satisfaction. If you have any questions, or find there are

missing or damaged parts, we guarantee you complete satisfaction through

direct assistance from our factory. To avoid unnecessary delays, please call

our TOO-FREE customer service number. Our Customer Service Agents will

provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. –Fri. 9 a.m. –5 p.m. PST

www.impex-fitness.com

info@impex-fitness.com

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you

operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or

operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN

IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine

near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear

robes or other clothing that could become caught in the machine. Running

or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or

physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to

properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.

THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS

WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING

ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL

INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS

PRODUCT.

SAVE THESE INSTRUCTIONS.

ASSEMBLY INSTRUCTION

Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches

NOTE: It is strongly recommended this machine be assembled by two or more people to

avoid possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#1) and Left Base Frame (#2) on the floor, at a right angle to each

other. Attach the Rear Vertical Beam (#5) to the joint and align the holes. Secure the top hole

with a M10 x 2 ¾” Carriage Bolt (#90), ∅3/4” Washer (#106) and M10 Aircraft Nut (#110). Secure

the bottom hole with a M10 x 2 ½” Allen Bolt (#97) and∅¾” Washer (#106). DO NOT tighten all

the nuts and bolts yet.

B.) Attach the Guide Rod Base (#24) diagonally to the two Base Frames. Secure it with a M10 x 2 ½”

Allen Bolt (#97) and∅1 ¼” Washer (#104) on each side on the Base.

C.) Attach the Right Vertical Beam (#3) to the Right Base Frame (#1). Secure it with two M10 x 2 ¾”

Carriage Bolts (#90), ∅3/4” Washers (#106), and M10 Aircraft Nuts (#110). Repeat the same

procedure to install the Left Vertical Beam (#4).

Diagram 1

STEP 2 (See Diagram 2)

A.) Attach the Right Upper Frame (#6) to the top of the Right Vertical Beam (#3). Secure it with two

M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two∅3/4” Washers (#106), and two

M10 Aircraft Nuts (#110).

B.) Attach the Left Upper Frame (#7) to the Left Vertical Beam (#4). Secure it with one M10 x 2 ½”

Allen Bolt (#97), ∅¾” Washer (#106), and 4” x 2” Bracket (#39) into the upper hole. Secure the

bottom hole with one M10 x 2 ¾” Carriage Bolt (#90), ∅¾” Washer (#106), and M10 Aircraft Nut

(#110).

C.)Attach both Left and Right Upper Frame (#7) & (#6) to the Rear Vertical Beam (#5). Secure it with

a M10 x 2 ½” Allen Bolt (#97) and∅¾” Washer (#106) to the upper hole. Secure the bottom hole

with a M10 x 2 ¾” Carriage Bolt (#90), ∅¾” Washer (#106) and M10 Aircraft Nut (#110).

D.)Align two Rubber Bumpers (#63) to the holes on the Guide Rod Base (#24). Push two Guide

Rods (#31) into the holes. Slide the Selector Stem (#44) onto the Guide Rods. Slide the Selector

Stem over the Selector Rod (#43). Please note this machine comes with 14 plates. You can

purchase another 5 more plates in the future to increase the weights. For now, drop the Selector

Stem down on the Selector Rod so there are 14 grooves underneath it. Secure it with a M10 x 1 ¾”

Allen Bolt (#98). DO NOT install the plates yet.

E.) Place the Top Socket Assembly (#25) over the top of the two Guide Rods. Secure it with two M6 x

5/8” Allen Bolts (#103).

F.) Secure the Top Socket Assembly (#25) to both Upper Frames (#6) & (#7) with a M10 x 2 ½” Allen

Bolt (#97) and∅1 ¼” Washer (#104) on each side.

G.)Securely tighten all nuts and bolts previously installed.

STEP 3 (See Diagram 3)

A.) Attach the Seat Support Frame (#14) to the Right Vertical Beam (#3). Secure it with two M10 x 2

¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two∅¾” Washers (#106) and two M10 Aircraft

Nuts (#110).

B.) Attach two Vertical Supports (#16) to the front of the Seat Support (#14). Secure them with two

M10 x 2 ¾” Carriage Bolts (#90), ∅¾” Washers (#106), and M10 Aircraft Nuts (#110).

DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach four ∅1” x ½” Bushings (#55) to the Leg Press Pivot Arm (#18). Attach the Pivot Arm to the

bracket on the Right Base Frame (#1). Secure it with one M12 x 3 1/8” Hex Head Bolt (#91), two

∅1” Washers (#105), and one M12 Aircraft Nut (#109).

B.) Attach two ∅1”x1/2” Bushings (#55) to the tube on the Leg Press Frame (#19). Attach the Leg

Press Frame (#19) to the top of the Pivot Arm (#18). Secure it with one M12 x 3 1/8” Hex Head

Bolt (#91), two∅1” Washers (#105), and one M12 Aircraft Nut (#109).

C.)Attach two ∅1”x1/2” Bushings (#55) to the pivot tube on the Right Base Frame (#1).

D.)Attach four D-Shaped Bushings (#57) to the top and bottom holes on the Leg Press Crank (#17).

Repeat for the other Crank. Attach the two Cranks to the pivot tube on the Right Base Frame (#1).

Secure them with a M12 x 5 11/16” Bolt (#94), two∅1” Washers (#105), and one M12 Aircraft Nut

(#109).

E.) Repeat the same procedure D above to install the Cranks to the Leg Press Frame (#19).

DIAGRAM 4

STEP 5 (See Diagram 5)

A.) Insert the Chromed Adjustment Tube (#20) into the Leg Press Frame (#19). Secure it with a

Quick Release Pin (#62).

B.) Attach the Foot Plate (#21) to the Chromed Tube (#20) and secure it with a L-Shaped Pin (#112).

C.)Attach the Bench Press Frame (#11) to the pivot tube on the Right Base Frame (#1). Insert a M10

x 8 5/8” Axle (#82) through the holes. Secure it with two ∅¾” Washers (#106) and M10 Aircraft

Nuts (#110) on both sides. Close the ends with two Round Caps (#108).

D.)Attach two Bench Press Handles (#12) to the Bench Press Frame (#11). Secure them with two

Quick Release Pins (#62).

E.) Attach the Seat (#40) to the Seat Support Frame (#14). Secure it with two∅5/8” Washers (#107)

and M8 x 2 ½” Allen Bolts (#101).

F.) Attach the Backrest Board (#41) to the Right Vertical Beam (#3). Secure it with two∅5/8”

Washers (#107) and M8 x 2 ½” Allen Bolts (#101).

DIAGRAM 5

Tabla de contenidos

Otros manuales de Gimnasio en casa de Impex

Impex

Impex APEX Manual de usuario

Impex

Impex TR-2 Manual de usuario

Impex

Impex MARCY SM-1000 Manual de usuario

Impex

Impex MARCY MCB-346 Manual de usuario

Impex

Impex Marcy Pro NS-6023RW Instrucciones de instalación y funcionamiento

Impex

Impex MARCY MWB-70500 Manual de usuario

Impex

Impex APEX TC-3502 Manual de usuario

Impex

Impex CB 555 Manual de usuario

Impex

Impex Marcy SB-685 Manual de usuario

Impex

Impex MARCY TC-3508 Manual de usuario

Impex

Impex Iron Grip Strength IGS-43 Manual de usuario

Impex

Impex Marcy Diamond MD-8861 Manual de usuario

Impex

Impex MARCY DIAMOND ELITE SM-1050 Manual de usuario

Impex

Impex OLYMPIAN Manual de usuario

Impex

Impex 120727 Manual de usuario

Impex

Impex MARCY DIAMOND MD-1559 Manual de usuario

Impex

Impex Marcy SB-350 Manual de usuario

Impex

Impex Iron Grip Strength IGS-705 Manual de usuario

Impex

Impex MARCY MKB-367RH Manual de usuario

Impex

Impex CB-204 Manual de usuario

Impex

Impex Marcy Diamond MD-859 Manual de usuario

Impex

Impex MWM 2001 Manual de usuario

Impex

Impex IRON GRIP STRENGTH TSA-5682 Manual de usuario

Impex

Impex Competitor CB 610 Manual del propietario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Weider

Weider 8300 Hard Drive Manual de usuario

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Weider

Weider 8700 I Guía de inicio rápido

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Weider

Weider WEMC10161 Manual de usuario

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario